One of the best stud finders you’ll ever use is the Franklin Sensors ProSensor 710. It’s unique in that there’s a whole bar of red lights that light up whenever it detects a stud. Unlike other sensors, which have a single light that stays on as it passes over the wood, the lights on the 710 tell you exactly where the wood stops and starts. No guesswork. Push a button, drag it over the wall and those hidden mysteries reveal themselves. You won’t even need to read the directions!

Aside from this being a fun gadget to own it is one of the most versatile tools for use around the house. You can look down your garbage disposal for the ring you just dropped, inside your car engine to see where the leak is and on and on. I love to see whats clogging my gutters both in the gutter and in the drain. One of the more unique tools. It’s going to be your new favorite.
Some moisture meters have pins that penetrate the surface of the wood. This can leave tiny holes that mar the surface and require filling. Others are pin-less. They have sensing plates that scan the wood beneath. However, not all pinless moisture meters are the same – look for one that uses technology that is not affected by the surface moisture in the wood, such as Wagner Meters IntelliSense™ Technology Moisture Meters.

For all of your wood cabinetry and joinery tools and supplies, Infinity Cutting Tools has got you covered. We offer joinery tools and accessories for making box joints, finger joints, pocket holes, dowel joinery, dovetails, and mortise-and-tenon joinery. When it comes to installing cabinet hardware like knobs, pulls, and hinges, check out our cabinet hardware installation solutions. 

No sadly, as I mentioned above, my table top ended up splitting, starting at a knot on the edge and going clear across the top (pre-drill those holes!!!), so I had to come up with another solution.  I didn’t want to go to the trouble of making another table top like this one, so I did a much easier and quicker solution…stain-grade plywood with decorative moulding attached to the edges. 
Bought 2 of these, one for the wife and one for me. We have a project we are doing that required cutting lots of MDF(medium density fiberboard) which is not good for you to breathe or get in your eyes (very tiny particles). I picked these because people said they worked well with glasses (which i wear) and because they had full protection from flying debris and also from the airborne dust.

We cut the supports 16 in. long, but you can place the second shelf at whatever height you like. Screw the end supports to the walls at each end. Use drywall anchors if you can’t hit a stud. Then mark the position of the middle supports onto the top and bottom shelves with a square and drill 5/32-in. clearance holes through the shelves. Drive 1-5/8-in. screws through the shelf into the supports. You can apply this same concept to garage storage. See how to build double-decker garage storage shelves here.


If planks are slightly cupped or twisted, have them planed at a local millwork shop or borrow a tabletop planer and tackle the job yourself. If planing yourself, first check planks for and remove nails and excess dirt*. Run planks though the planer, stripping a small amount of wood from each side as you plane. While the board is going through the planer, manually adjust the depth of the cut to compensate for irregular thickness (or twist) over the board’s length. You can hurt yourself or damage the board or planer if you do not manually adjust as you go. Keep running boards through the planer until the blade has lightly stripped each surface. Next, rip boards on a table saw to create straight edges; planks do not have to be identical in width.
You can also use Google image search to research a project. Unlike the PDF search, the image search provides a photo of what the project will look like, which is helpful in determining if you want to pursue building it. By doing an image search for how to build a step stool, you will have a ton of options that all lead to woodworking plans of various quality. (The how to part of these is important—otherwise you’ll just get pictures of step stools.)
When you buy the wood, look for pieces that aren’t warped, excessively longer or shorter than the others, and, if you can get lucky, don’t carry the telltale “new wood” planer marks. We purchased the most inexpensive wood that we could find. You’ll likely find them in 2- and 4-ft pieces. If you have a saw at home, you might consider getting the 4 ft pieces to decrease the cost of your project a bit.
Rachel Teodoro and Holy-Craft.com, 2010-present. Unauthorized use and/or duplication of this material without express and written permission from this site’s author and/or owner is strictly prohibited. Excerpts and links may be used and up to one photo can posted, provided that full and clear credit is given to Rachel Teodoro and Holy Craft with appropriate and specific direction to the original content.
×