Clean wooden gutters of any loose debris and cut to a manageable length. Miter down to form an approximately 40" x 94" rectangle. Coat the corners with wood glue and fasten together with 15-gauge finish nails. If miters are tight 45-degree cuts, box should be square. Double check diagonal measurements before fastening completely. The two diagonal measurements should be as close to equal as possible.
Clamp curved caul edges inwards so they align tabletop boards in the middle, then torque up the main clamps to draw the boards together. If the width of boards you’re using allow it, pre-glue boards for your tabletop in sections that are just narrow enough to fit within your thickness planer. Run these through the planer to clean and level the glue joints, then move back to clamps for final glue up. Working in stages like this reduces the number of glue joints you need to sand smooth and level later.
Here’s another example of a stenciled tabletop.  Remarkably, this table was destined for the dump when Pretty Handy Girl pulled it from a dumpster.  With a stencil, primer and paint, some distressing, glazing and sealing, she gave this beauty a second life – one in which it looks like it came directly from old world Scandinavia. // Pretty Handy Girl
When you buy the wood, look for pieces that aren’t warped, excessively longer or shorter than the others, and, if you can get lucky, don’t carry the telltale “new wood” planer marks. We purchased the most inexpensive wood that we could find. You’ll likely find them in 2- and 4-ft pieces. If you have a saw at home, you might consider getting the 4 ft pieces to decrease the cost of your project a bit.
I’ve been doing a lot of remodeling on my house and this wristband has come in pretty handy. The magnets work very well and able to hold all the screws, washers, and bolts for the different projects I’m working on. The pockets are a great addition too for holding plastic items. In fact, I found it useful for holding a small pencil where I can have quick access to for marking measurements for cuts. Overall it’s a great quality wristband and would definitely recommend.

Or if you are in the search for a protectant that is specifically for woodworking tools, then you should check out the Restore Blade and Bit Cleaner 500. Not only is this cleaner one of the best woodworking accessories, it’s also environmentally friendly and safe to breathe in while using. This cleaner is the perfect companion for circular saws, miter saws, router bits, drill bits, as well as a variety of woodworking tools. While protecting your tools from rust and corrosion, it’s liquid form will not damage any wood materials that you may be working on at the time.
We will suggest you select the simple Birdhouse if you are new at woodworking but be sure to select its design with respect to the place where you are going to hang/place it. One of our simple Birdhouse tutorials will help you building one. We have managed to include a source tutorial below that will help you to understand illustrates and the instruction to building a simple Birdhouse.
It is becoming more popular in this DIY age for people to want to make things themselves, and we are seeing a return to woodworking as a hobby or pastime. The garage is transformed into a workshop, with a workbench a set of woodworking tools and of course a beer fridge. Beautiful handmade woodworking projects can be achieved with some practice, a good set of plans and the right woodworking tools.
We cut the supports 16 in. long, but you can place the second shelf at whatever height you like. Screw the end supports to the walls at each end. Use drywall anchors if you can’t hit a stud. Then mark the position of the middle supports onto the top and bottom shelves with a square and drill 5/32-in. clearance holes through the shelves. Drive 1-5/8-in. screws through the shelf into the supports. You can apply this same concept to garage storage. See how to build double-decker garage storage shelves here.

OK, the Long Ranger’s been around since Marconi. But we love it. Simply put, this Long Ranger III Remote Dust Collector Switch is a remote system for turning on your dust collector out in the shop from whatever tool you’re operating. It plugs into the wall, you plug your dust collector into that and you’re done. Push the button on your remote and it fires right up. It’s saved us about two years and 1,300 miles of walking back and forth to the dust collector switch.
Rolled-on poly looks terrible at first, but the bubbles disappear in minutes, leaving a smoother surface than most of us can achieve with a brush. Beware of ridges formed by the edges of the roller and humps where you start and stop. You can minimize both of those flaws by applying lighter coats. We experimented with several kinds of rollers and got the best results with microfiber mini rollers. We also tried rolling on water-based poly; don’t do it.
By completing a form on this website, you will be able to receive email correspondence from Canadian Woodworking.   These emails may include information on upcoming events or special offers for subscribers. If you do not wish to receive email correspondence please email orderdesk@canadianwoodworking.com  and ask to be removed from our email list. Every email that we send to you will include an "opt-out" from receiving future email correspondence. 

There are lots of clear finishes. But for a combination of usability and durability, you can’t beat polyurethane. Oil-based poly, which dries slower than water-based, is best for beginners because it allows more working time. The other important difference is clarity: Water-based poly is absolutely colorless, while oil-based has an amber tone, which can be good or bad depending on the look you want.
×