I started by doing some searches around the ol’ internet to find other folks who’ve built their own tables. Using the images and information I found, I started drawing up plans. My table is approximately 6’x44″x31″ (LxWxH). You may find different dimensions work better for you (31″ is pretty tall)–so make your plans however you like. I also built leaves that make the table 8.5’ long.
Open rafters and trusses are an endless source of falling dust. So if you’re working under an open ceiling, hang plastic sheeting above. Keep the plastic at least 12 in. from light fixtures or remove the bulbs. Sometimes, adding plastic ‘walls’ is a lot easier than cleaning up the entire area. If you’re using oil-based finishes, hang the sheets about a foot from the floor to allow for ventilation.
Build this handy stool in one hour and park it in your closet. You can also use it as a step to reach the high shelf. All you need is a 4 x 4-ft. sheet of 3/4-in. plywood, wood glue and a handful of 8d finish nails. Cut the plywood pieces according to the illustration. Spread wood glue on the joints, then nail them together with 8d finish nails. First nail through the sides into the back. Then nail through the top into the sides and back. Finally, mark the location of the two shelves and nail through the sides into the shelves. Don’t have floor space to spare? Build these super simple wall-mounted shoe organizers instead!
We call them strongbacks and we use them on every tabletop we build. It's just a scrap strip of 3/4" plywood, with 3/4" pocket holes drilled about ever few inches. The strongback is attached to the bottom of the tabletop as the glue dries. The square edge of the plywood prevents the tabletop from warping or cupping as it dries. Then we remove the strongbacks (and save them for the next tabletop) when we attach the tabletop to the base.

Angel Crafts | Baby Crafts | Basketry | Beading | Candle & Soap Making | Computer Crafts | Crochet | Knitting | Doll-Making | Drawing & Painting | Family Tree | Felt Food | Felt Flower | Floral | Gardening Crafts | Greeting Cards | Jewelry & Beading | Kids Crafts | Preschool Printables | Locker Hooking | Nail Art | Nature Crafts | Needlework | Owl Crafts | Painting | Paint Chips | Patriotic Crafts | Pennants & Buntings | Plastic Canvas | Quilting | Rubber Stamps | Scrapbooking | Sewing | Shoe Crafts | Silhouette | Soap Making | Tatting | Wedding Crafts | Woodworking

Okay, let’s stain this beast. I should explain that we used Rustoleum’s Dark Walnut Ultimate Wood Stain, but we did it wrong. We failed to mix it well before applying it, resulting in a color we really liked–but not the color this stain is designed to create. When we came back to do a second coat, we stirred it well, resulting in a coat that looked like purple paint. I had to sand it off and start over. So, don’t follow my lead here–follow the can’s directions and TEST before staining all of your new masterpiece!
I had been looking forward to this part—applying the Minwax Gel Stain. First, I tested the stains on a leftover board to confirm my suspicion that, used together, the three stains would complement one another perfectly. When the test confirmed my suspicions, I proceeded to stir each stain until it developed a creamy, smooth consistency—nothing like the watery liquid you might be used to. With its thicker formulation, Minwax Gel Stain has been specially designed to be user-friendly and easy to apply. With either a foam brush or a rag, the Gel Stain goes on in a controlled way, and you don’t have to worry about drips; just let it sit on the wood for about three minutes and wipe away the excess with a rag. Once I had finished staining all the wood pieces in alternating colors—Hickory, Cherrywood, and Honey Maple—I let about eight hours of dry time elapse. Though it wasn’t strictly necessary, I decided to darken the stain colors a bit by applying a second coat, using the same technique I’d used with the first.
After your table is pieced together, you will flip it over {remember, you've been working on it upside down} and sand it.  My husband isn't a big fan of the planks and worried about cups and plates getting stuck and spilled on the uneven parts of the boards, so he went to town with the sander. You can keep more of the plank look by sanding it less.
Using pocket holes to attach the stool base to the stool top prevents the top from moving during seasonal changes. It’s also not a good idea to drive screws through the edge of the apron into the table top. Over time the top could crack or the top could have enough force to push or pull the joints of the base apart. Skate over to Mistakes with Wood Can Cause Your DIY Furniture to Crack to see more about how I incorrectly attached the top on the stool.
There are lots of clear finishes. But for a combination of usability and durability, you can’t beat polyurethane. Oil-based poly, which dries slower than water-based, is best for beginners because it allows more working time. The other important difference is clarity: Water-based poly is absolutely colorless, while oil-based has an amber tone, which can be good or bad depending on the look you want.

Consider building your tabletop out of boards about 6" wide (1x6 or 2x6), or close in size (I use x4 and x8 boards on occasion). If you go smaller, you'll be adding more joints, which means more pocket holes and more sanding. If you go with a wider board, the board itself may cup over time, creating high and low points on your tabletop. I personally find x6 boards to be that happy medium.
This is a very colorful and fun project. The idea is to use an old table with a top that you don’t really like and to give it a makeover. You don’t need paint for this project, just a lot of colored tape. Use it to make stripes to cover the entire surface of the tabletop. You can also wrap the edges in tape. You can also cover it with lacquer or add plexiglass on top to protect the design. 

Copyright 2018 by Cut The Wood. CutTheWood.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Additionally, CutTheWood.com participates in various other affiliate programs, and we sometimes get a commission through purchases made through our links.
If you can beg or borrow a pocket hole jig you dont have to predrill holes. I haven’t done a table top other than a workbench(Plywood!) but I have done cabinets and beds. The Kreg jig makes joining easy. A lighter stain colour would cut down on the grain marks, or a heavier application like an espresso stain. I will throw you a pic when I finish my table and show you what I mean.
After all slots are cut, stand each board on end and coat the edge of jointed side with wood glue. Next coat the biscuits with glue. Insert biscuits in one side only of each board, then insert glued biscuits in the empty joint of the next board. Assemble planks in order until the top is complete. Don't worry about small gaps. Next, carefully lay the top down and attach pipe clamps at roughly 1' intervals. Slowly tighten each pipe clamp in a consistent fashion until the gaps disappear*. Small amounts of glue can be removed when dry; scrape up any puddled glue with a plastic putty knife. To minimize sanding later, avoid working glue into the top of the wood. Let the top set overnight.
Nightstand table plans have everything you need to create a bedside table to keep every needy thing at reach at night time. This Nigh Stand plan is quite different in design from the most of the other plans. This stand has not only the three regular drawers but also having a hidden drawer that uses a secret locking mechanism to keep contents securely.
No, it’s not a blood pressure tester. It’s an inflatable shim sold by Calculated industries. What in the world would you do with an Air Shim? Well, you could hold a window in position (by yourself) while setting the permanent shims, or prop up a door slab during installation without scratching the hardwood floor. Use it to align base cabinets or level appliances. You could even trick your big, burly buddy by betting him that your 10-year-old can pick him up off the ground… you will win that bet because the Air Shim is easy enough for anyone to pump and it holds up to 300-lbs. Deflate it as slow as you want for uber precision adjustments.

Using pocket holes to attach the stool base to the stool top prevents the top from moving during seasonal changes. It’s also not a good idea to drive screws through the edge of the apron into the table top. Over time the top could crack or the top could have enough force to push or pull the joints of the base apart. Skate over to Mistakes with Wood Can Cause Your DIY Furniture to Crack to see more about how I incorrectly attached the top on the stool.


Work at a place where you’re required to wear a steel-toe boot? Then listen up. Wolverine just introduced a new boot that’s much more comfortable but still offers solid impact protection. Instead of steel, CarbonMAX boots have a protective cap made of carbon nanotubes, making them lighter and thinner. And if anyone knows about making comfortable work boots, it’s Wolverine—they’ve been making them for more than 130 years.
It’s important to have an understanding of wood when building DIY furniture projects. Not just how to cut, and assemble with wood but also to understand how it works. In Mistakes with Wood Can Cause Your DIY Furniture to Crack we talked about how wood is hygroscopic. Simply put, hygroscopic means it absorbs moisture from the air. Seasonal changes cause wood to absorb and release moisture.

Pallet tables are very common and very easy to make. To make it you’ll need about half of a wood pallet. Decide the dimensions for the table and then remove some of the boards and cut them to size. Reattach them using nails and then sand the table. Then you can stain or seal the wood if you want. At the end, you can either add legs, casters or leave the table as such.{found on hernewleaf}.
When it comes to choosing a finish there are two main choices. The typical approach of stain and urethane creates a smooth, wipeable surface, but when that finish eventually wears through, there’s no way of repairing it attractively. Sanding back to bare wood and refinishing is the only way to make it respectable again. Oil and wax finishes, on the other hand, take more time to apply initially, but they’re easily repaired and rejuvenated with the tabletop in place. Regular reapplication works just fine.
Using shelving in your room or kitchen is a great way to arrange and de-clutter space… I know, such ground-breaking term it is. Do not write me off yet, I just want to show you how you can build some clean floating corner shelving that appears to have no brackets. You can create them at no cost, and the hardest part of the plan is figuring out what you are going to put on these shelves when you are finished.

Hi Mitchell – Thank you for the heads up… I thought I mentioned that in that in the post, but you’re right, I didn’t. Yes, wood expands across its width, so in order to allow for expansion/contraction there should be a small gap where the edges of the boards meet the apron. You don’t need a gap where the ends of the board meet the apron because wood doesn’t really expand/contract in this direction.
Are you redecorating your home but can’t seem to find the right table to complete your décor? Don’t worry too much because there are plenty of alternatives. There’s always a DIY project that can help you out. For example, we just found these beautiful DIY tables and we’re sure there are plenty more where these came from. Let’s take a look at them and see them closely.
This plan is probably the easiest plan ever added in the list. The one who is working on this project, don’t need any professional skills but just knowing some basics of woodworking will be enough for this DIY. You will get step by step detailed process of this tutorial in the source linked tutorial. This tutorial will surely help you to build this plan quickly.

I am so glad to see this. It is exactly what I have been looking for. I have had a similar idea in my head for years but didn't know how to bring it together, and I wasn't sure how it would actually turn out. Yours is beautiful. It is nice to start with an idea of how the project will actually look when I am done. My table is 25 years old with a laminate top. The reason I want to cover instead of replacing it does that it is the first purchase my husband and I made together. It has seen 25 years of abuse by three little (now big!) boys and by me, the messy crafter. But I cannot imagine ever getting rid of this table. Plus it's not like I'm going to get less messy, so investing in an expensive table would be crazy. I love how I can take this top off and still do the messy damaging things on it. I am bookmarking this and if I ever get around to actually doing it LOL, I will send you pics


She has permanently glued and screwed the tabletop within that four-sided, mitered frame. Attaching the skirt to the long edges of the wide boards is no problem, but fastening them to the end grain of the wide boards, as shown in the photo above, is. The builder has constricted the wide boards' movement, and as they grow or shrink in width but are held in place by those end-caps, they will warp and split, making this a short-lived piece of furniture.
If you bought this superb polished table in a store, it would cost you a fortune, but our detailed instructions will help you make one for less than $100. And it looks like highly polished stone, but no-one would know it’s actually made from concrete with a wooden base. Also, you can embellish the top with leaf prints, like the table shown here, or personalize it with glass or mosaic tiles or imprints of seashells.
Cedar Mini Decorative Planters/Boxes Using Interlocking Dovetail Joints Having a cedar mill within an hour of my shop allows me to work with some very nice wood. While cedar can be brittle, it is wonderful to work with and makes putting these decorative boxes together a breeze. When working with cedar I am always looking for pieces that have what is known as “heartwood”. This is the red portion of the wood. When first planed or sanded, this heartwood is almost pink in color but takes polyurethane or spar finish well giving a vibrant dark red when applied. If left untreated, cedar will turn gray in direct sunlight and a dull red color from normal household light. These boxes have been treated with a wiping polyurethane mix that allows me to apply it with a cotton rag instead of a brush. It’s faster to apply, doesn’t run and dries fast enough to apply two coats in a day. So applying 5-6 coats only takes 2-3 days to accomplish. I assembled the boxes using a dovetail joint which provides both strength and decorative at the same time. A fan shaped tenon that forms a tight interlocking joint when fitted into a corresponding mortise. The dovetails on these boxes are shown on the length of the box and not the end where the handles are located. I use a dovetail jig and a router to make these joints which is more efficient. Depending on how the client will use the box I may or may not drill two holes in the bottom of the box. If they are built to be used as outside planters then I drill 2, half inch holes in the bottom for water to drain. If they are to be used inside as a table center piece or fireplace mantle decorative box, then I do not drill the hole. In the end they are strong, durable and beautiful no matter how they are used.

Whether you're new to woodworking or you've been doing it for years, Woodcraft's selection of woodworking projects is one the best places to find your next big project. Whether you're looking to make wooden furniture, pens, toys, jewelry boxes, or any other project in between, the avid woodworker is sure to find his or her next masterpiece here. Find hundreds of detailed woodworking plans with highly accurate illustrations, instructions, and dimensions. Be sure to check out our Make Something blog to learn expert insights and inspiration for your next woodworking project.


The Wilton ATV All-Terrain Vise is a tool for those of you who work out of your pickup at job sites and need a serious on-site vise. And this vise is worth the price! It slips into any 2-in. receiver hitch and has a sizable flat anvil area for pounding. It comes with a bracket for attaching to any sturdy surface, such as a trailer, if you don’t want to use your truck.


It’s important to have an understanding of wood when building DIY furniture projects. Not just how to cut, and assemble with wood but also to understand how it works. In Mistakes with Wood Can Cause Your DIY Furniture to Crack we talked about how wood is hygroscopic. Simply put, hygroscopic means it absorbs moisture from the air. Seasonal changes cause wood to absorb and release moisture.

Nightstand table plans have everything you need to create a bedside table to keep every needy thing at reach at night time. This Nigh Stand plan is quite different in design from the most of the other plans. This stand has not only the three regular drawers but also having a hidden drawer that uses a secret locking mechanism to keep contents securely.
California Air Tools makes great air compressors. One of their most popular models is the 2010A. The aluminum tank makes it light (35-lbs.) and eliminates those stains from rusty water draining from rusty tanks. The oil-free dual-piston pump provides a fast recovery time—fast enough to run a framing gun. It also draws less power and performs well in cold weather. There’s no doubt that you’re going to like all the features of this compressor, but you’re going to love how quiet it is. It runs at about 60-dB, which is about the same as a conversation in a restaurant. So, no more hollering at coworkers or cranking up the radio to hear the music over a screaming compressor.
As with most websites, we do log web visits. This information, however, does not have a link to you personally. These logs help us understand the needs of our audience and the areas of our site that you do or do not find useful. When you simply browse our site, no personal information is being collected.  We may disclose this non-personal information to third parties such as sponsors, clients or advertisers.
Holy Craft came up with a genius solution for a scratched and worn dining table!  If your table looks a little worse for wear, but you still plan on using it for messy situations like painting and crafting, you’ll love this wood plank tabletop cover.  Slide it on for nice dinners and entertaining company, and tuck it away when your kids use play dough! // Holy Craft on Remodelaholic
A dispensing gun allows you to save foam if the job requires less than a full can. Once the job is finished, just set the gun aside until the next time you need it. Leave the can on the gun if you know it will be used in less than 30 days, or pull the can off, cap it and then clean out the gun with cleaning solution. Besides saving you money on foam, the dispensing gun provides much greater control because you’re not working with a flimsy straw, and the trigger can be adjusted with a turning setscrew to control the rate of flow—nice! Spray foam dispensing guns are available online and at home centers.
×