Consider building your tabletop out of boards about 6" wide (1x6 or 2x6), or close in size (I use x4 and x8 boards on occasion). If you go smaller, you'll be adding more joints, which means more pocket holes and more sanding. If you go with a wider board, the board itself may cup over time, creating high and low points on your tabletop. I personally find x6 boards to be that happy medium.
Your monster of a table is going to be HEAVY, so I strongly recommend moving it to its final destination in two pieces–lay a blanket down in your dining room, put the top on it upside down, then the frame upside down on top of that. Attach a couple 2×4 supports across the frame for good measure, then begin the frustrating process of centering the frame on the top. Once you have the top centered, attach your brackets–I did two on each end and three on each side.
Build your own platform bed frame at your home by following the source linked tutorial given above. The source link also includes more pictures that can help you to build a better bed frame. You can see a step by step set of instructions and guidelines to follow with real life pictures, as well as you can download a PDF file detailing the list of materials and tools you’ll need, know about the length of every board, and most importantly color-coded illustrations of the building process.
Ridgid has a new C-style close-quarter tubing cutter that slices through both 1/2-in. and 3/4-in. tubing, which means one less tool to carry and fumble around for. The cutting wheel is spring loaded so it needs no adjustment as you spin the cutter, and the outside surface has screwdriver slots for getting leverage in tight spaces. The 1/2 – 3/4 Rigid tubing cutter costs $32 and is available at plumbing supply stores and online retailers.
Turning over the sturdy tabletop, I felt a thrill of vindication. Clearly, it wasn’t a mistake in the end to use all three stains for the same project. Before I could consider the job done, though, I would need to apply sealer—Minwax Helmsman Spar Urethane—to protect the wood from moisture, UV rays, and the wear and tear of day-to-day life. This was my first time experimenting with a spray-application sealer, and I loved it. Obviously, it’s important to have proper ventilation in your work area, and you’ve got to shake the can vigorously before spraying, but so long as you remember the basics, spraying couldn’t be more straightforward. Holding the Helmsman Spar Urethane can about a foot from the surface, spray in a series of even strokes, always in the same direction, until you’ve completed the first coat. Let the sealer dry for about four hours before applying any additional coats, and for best results, sand the entire surface before each application of a new layer.
For starters, this DIY wood table is for my son to keep his Lego projects and erector set buildings on. Secretly, it’s for me because, in turn, it will keep the Legos from being scattered all over my house. We decided on measurements of 60″ long x 18″ deep for the table top. Now that I know how big I want our homemade table to be I reached out to Osborne Wood Products to find out what the next step is for building a table. They were super helpful and made it very easy to order the table base kit. We let them know the measurements for the table top as well as how much of an overhang. We then choose the traditional dining table legs in soft maple along with a 4″ wood skirt also in soft maple. The furniture kit came well packaged and rather quickly.
Reclaimed Wood from Corn Crib HOW TO DESIGN AND BUILD AN ENTRY WAY COAT RACK AND BENCH There was a door in granddad’s home the client wanted to preserve and wondered, if they provided the wood, could I build an entryway coat rack and bench using the door as part of the build. The wood they wanted to provide, well, that was from the family owned Tennessee corn crib that had been torn down and they didn’t want to lose the wood or the memories. Not only was this a corncrib but it was eventually used by the great grandchildren as a play house. So for the client there are as many memories in this build as there are colors. THIS PROJECT TRULY DEFINES THE “CUSTOM” in BAYNE CUSTOM WOODWORKING. I spent some time to design a simple layout in @sketchup_official so the client could approve the idea I had in mind. The wood showed up in two deliveries so we stacked it outside because this was the first time I worked with barn wood. I did not want to introduce possible termites to my shop. So my first call was to my pest guy asking how I would treat the wood for termites. Much to my relief he said I had nothing to worry about. This was “real” wood! Not nominal at all, nominal is how we buy our wood at a local hardware store. Where a 2×4 is actually 1 ½ x 3 ½ . These 2×4’s were at least 2”x4”’s if not more and were hard, heavy and dusty, did I say heavy? After cutting to length on my handy @DewaltTough miter saw, I had to take them to my @ridgidpowertools table saw and square up the bottoms only. I was very careful not to lose any of the original saw marks and character because that would ruin the entire purpose. For someone who likes clean, crisp edges, this was a bit of a challenge. I used @kregjig Kreg Jig® K4 Master System to join all the pieces of the base, the seat frame and the supports to join the two together. I was very careful to hide all of the pocket holes so they could not be seen from any angle. I used Titebond Products original interior wood glue to join all the pieces together. The next item was to assemble the back which included grandad’s door as the center piece. The door was only 71 ½ tall which determined the overall height of the project. Part of this back also includes two live edge pieces that we picked to use as the “L” shaped wings or side walls. The door measured 24” which left me with 6” on each side to make up the final size of 36”. So I chose two of the straightest boards that were closest to 6” and cut them to width so as not to waste any wood or lose any character. I used the Kreg Jig® K4 Master System
I've worn this apron in my studio/workshop several times now, and I really like it. It's more expensive than some, but the materials and construction are first-rate. I rarely give five stars, but the workmanship on this apron is impressive. The fabric is substantial and, although a bit stiff at present, comfortable to wear. The strap and grommet system is pretty clever, allowing a good fit for most, I would think. I'm a 5'-7" not-skinny woman, and I'm able to cross the straps at the small of my back and then tie them in front, so I'm guessing there would be plenty of strap length for bigger men. The straps sit comfortably on my shoulders. And all the pockets are great!
Rachel Teodoro and Holy-Craft.com, 2010-present. Unauthorized use and/or duplication of this material without express and written permission from this site’s author and/or owner is strictly prohibited. Excerpts and links may be used and up to one photo can posted, provided that full and clear credit is given to Rachel Teodoro and Holy Craft with appropriate and specific direction to the original content.