If you bought this superb polished table in a store, it would cost you a fortune, but our detailed instructions will help you make one for less than $100. And it looks like highly polished stone, but no-one would know it’s actually made from concrete with a wooden base. Also, you can embellish the top with leaf prints, like the table shown here, or personalize it with glass or mosaic tiles or imprints of seashells.
Carefully lay the top down and attach pipe clamps at roughly 1' intervals. Slowly tighten each pipe clamp in a consistent fashion until the gaps disappear. Small amounts of glue can be removed when dry; scrape up any puddled glue with a plastic putty knife. To minimize sanding later, avoid working glue into the top of the wood. Let the top set overnight.

Google is probably the first place where most people would start searching for woodworking plans, but often the top results can be a mix of articles and how-to pieces that just aren’t detailed enough. Sometimes they’ll link to the plans (like we try to here at Lifehacker), but other times, they’re just showing off a cool project. There are better, more precise ways of finding what you’re looking for.
Example Entertainment Center: $25 for plans + $750 for materials + $1200 for good quality tools = $1975. Less than a few grand! Of course you don't have to buy brand new tools; search the sale lists online (i.e. Craigslist, Freecycle.org, etc.) in your area. You are sure to find some good deals on power tools and even materials! (A good set of tools includes a table saw, miter saw, nail gun and compressor and four piece cordless tool set.)
Clean wooden gutters of any loose debris and cut to a manageable length. Miter down to form an approximately 40" x 94" rectangle. Coat the corners with wood glue and fasten together with 15-gauge finish nails. If miters are tight 45-degree cuts, box should be square. Double check diagonal measurements before fastening completely. The two diagonal measurements should be as close to equal as possible.

When a fluorescent bulb goes dark, the problem can actually be one of three things: the bulb, the ballasts, or the pins. By touching the bulb with its extending wand, this niche diagnostic tool can isolate the problem. You probably don’t need one for your basement lights, but the guy who works maintenance in a 12-story office building loves this thing.
A super simple iPad Dock/stand made out of a single block of wood features an angled groove which gets to support the tablet device and a cut in a hole to revise access to the home button of your iPad. It’s possible to drill an access channel in the stand through which you can run a charging cable, although this mini stripped back iPad stand may have very limited functions.
Example Entertainment Center: $25 for plans + $750 for materials + $1200 for good quality tools = $1975. Less than a few grand! Of course you don't have to buy brand new tools; search the sale lists online (i.e. Craigslist, Freecycle.org, etc.) in your area. You are sure to find some good deals on power tools and even materials! (A good set of tools includes a table saw, miter saw, nail gun and compressor and four piece cordless tool set.)
And the fact is that you can make your own patio chair with several old but still good pallets. Here we are providing a tutorial that everybody can follow easily – it is very well-written and also self-explanatory, which is great for those who are a beginner at woodworking and have never completed a DIY project before. As you don’t need to be a professional woodworker or a handyman to complete this project, so it is not a difficult task – all you need is a bit of determination!​
Diablo's Adjustable Rail and Stile Router Bit Sets Diablo's Adjustable Rail and Stile Router Bit Sets create perfect fitting rail and stile doors for 5/8 in. to 1-1/4 in. stock. Featuring TiCo carbide with titanium these bits provide a long cutting life and ultra-fine finish. Perma-shield Diablo's high performance coating reduces friction and build-up on the bits. The ...  More + Product Details Close
I've worn this apron in my studio/workshop several times now, and I really like it. It's more expensive than some, but the materials and construction are first-rate. I rarely give five stars, but the workmanship on this apron is impressive. The fabric is substantial and, although a bit stiff at present, comfortable to wear. The strap and grommet system is pretty clever, allowing a good fit for most, I would think. I'm a 5'-7" not-skinny woman, and I'm able to cross the straps at the small of my back and then tie them in front, so I'm guessing there would be plenty of strap length for bigger men. The straps sit comfortably on my shoulders. And all the pockets are great!
This is another wood table but this time with a more elaborate design. Instead of using a large log, this time you’ll need several small ones. The idea is to cut them to the same height and to try to create a mosaic with them. You can glue them together and you can also wrap a piece of rope or something similar around them. You should be able to create an original coffee table.
A few days back, I was searching for some cool DIY plans. So, I got to work and ended up coming up with some easy to follow project and an awesome new ice chest cooler to have out on the deck! It was going to be perfect for summer hangouts and barbecues. It was a fun and practical plan to work on and I know you will have fun tackling select a design from this plan and start building your own. Enjoy learning how you can build a rustic cooler also sing the video tutorial and source tutorial plan!

Thermal imaging systems work great at finding water leaks, electrical hot spots, and insulation gaps in walls. But until recently, thermal imaging systems were not a practical tool for the average contractor because they cost thousands of dollars and were the size of a microwave oven. But now this extremely helpful technology is accessible. FLIR’s new C2 compact imager is pocket-size but has most of the same important features as larger models. The touch screen controls are intuitive to use, and it acts as a regular camera as well, which helps when pointing out to homeowners or coworkers where exactly the trouble spots are. They also make models that work with your smartphone.
With a collection of workshop tools--whether for construction jobs or for around the DIY house projects--it’s top priority to make sure all of your tools are in the best shape and are taken care of. Tools don’t come at a cheap price, so proper care is essential in order for them to last for a long time. Unfortunately, after much usage, wear, tear, and rusting of tools tend to happen. Luckily, at Bora Tools, we sell a vast variety of workshop accessories that are specific to cleaning and restoring needs. From waxes, polishes, rust removers, to covers, racks, and more, we have an abundance of products that are designed to keep your high-quality, expensive tools in prime condition all year round.
Breaking down heavy sheet-goods on a jobsite table saw is difficult, and dang near impossible when working alone. That’s where a track saw comes in handy. A good quality track saw can produce cabinet saw results out on any job. Now, this portable tool is even more portable. The FESTOOL TSC 55 is a cordless saw that has the same features and performs just as well as FESTOOL’s corded saw, including the cut capacity and blade speed. It also has a collection bag that actually works, collecting up to 90% of the dust. The batteries are compatible with other FESTOOL products and the saw runs on their standard tracks.
A lot of woodworkers share their projects through their own blogs or YouTube channels. In fact, we’ve shared many of them here before, including, Woodworking for Mere Mortals, The Wood Whisperer, Matthias Wandel, April Wilkerson, Sawdust Girl, House of Wood, FixThisBuildThat, Pneumatic Addict, Build-Basic, Rogue Engineer, Her Tool Belt, and Ana White. The best YouTube woodworkers create great videos, but also provide a complete blog post with a cut list, tools, materials, and instructions. Find your favorites and save them for when you’re doing your searches.
The owners, webmasters, administrators, authors and editors, expressly disclaim all and any liability to any person, whether a user of this website or not, in respect of anything and of the consequences of anything done or omitted to be done by any such person in reliance, whether whole or partial, upon the whole or any part of the contents of this website. Please exercise caution when working with any tools or machinery. Follow common safety rules and precautions as outlined in any manuals related to the equipment being used. If advice or other expert assistance is required, the services of a competent professional person should be sought.
This DIY has a bit of a backstory: In my basement workshop—as a byproduct of about a half dozen previous projects—I’d managed to accumulate a small mountain of scrap wood. Though the pieces varied in size, most were 2×4 boards. For weeks, I pondered the question of how to use them. There wasn’t enough material to build anything substantial, but at the same time, this was much more wood than I would feel comfortable chucking or committing to kindling. I suddenly seized on the idea of turning those leftover boards into a rustic tabletop, but then I let the project momentum slow to a creep, and in the blink of an eye another few weeks had gone zooming by. Things finally came to a head one day when I was scanning the local giveaway listings. There, I discovered that one of my neighbors was trying to get rid of an old metal garden table. Upon seeing the pictures, I knew immediately that this would be a great table to top with the scrap wood surface I’d been planning to make with all those 2x4s!
A few days back, I was searching for some cool DIY plans. So, I got to work and ended up coming up with some easy to follow project and an awesome new ice chest cooler to have out on the deck! It was going to be perfect for summer hangouts and barbecues. It was a fun and practical plan to work on and I know you will have fun tackling select a design from this plan and start building your own. Enjoy learning how you can build a rustic cooler also sing the video tutorial and source tutorial plan!
A few days back, I was searching for some cool DIY plans. So, I got to work and ended up coming up with some easy to follow project and an awesome new ice chest cooler to have out on the deck! It was going to be perfect for summer hangouts and barbecues. It was a fun and practical plan to work on and I know you will have fun tackling select a design from this plan and start building your own. Enjoy learning how you can build a rustic cooler also sing the video tutorial and source tutorial plan!
Just redid my dining room table with this technique and I an observation/suggestion others might find helpful. The boards did not line up well putting it together upside down, even on a flat concrete floor with me standing on the boards while they were screwed. I would have combined biscuits with the pocket holes to ensure a better alignment of the boards. Lots of sanding was required after assembly, and this might not be a huge deal with pine, but I used hard maple so it was quite a chore even with a belt sander. Also, be aware that the 1x2s around the edge may not line up perfectly -- I had to trim about an eighth inch from each side after assembly to get nice smooth, even edges. Not a big deal, but the top turned out a little smaller than the specifications I was give by SheWhoMustBeObeyed. Otherwise our table now looks great, and thank you for the post!
This is a very colorful and fun project. The idea is to use an old table with a top that you don’t really like and to give it a makeover. You don’t need paint for this project, just a lot of colored tape. Use it to make stripes to cover the entire surface of the tabletop. You can also wrap the edges in tape. You can also cover it with lacquer or add plexiglass on top to protect the design.
Do you have older 18V DeWalt tools that are still near and dear to your heart but need new batteries? Consider firing up those old tools with 21st century technology. Now, 18V tools can be run on powerful 20V lithium Ion batteries with DeWalt’s new battery adapter. The adapter slides into the tool and the battery hooks onto the adapter. It works on most 18V DeWalt tools but not all. It’s sold two ways: the adapter alone (DCA1820), or the adapter with two compact 20V, 2.OAh batteries and charger. Now you’ll be able to hold on to your favorite cordless reciprocating saw forever!
By video tutorial, you will get step by step process instructions of making a nice wooden folding sling chair from scratch. However, my first wooden chair was not the best one, but it was good enough to motivate me to make some more folding chairs like this one. If I can make this, you too can make one yourself. You can browse the internet for more folding sling chairs ideas and start making one now.

Oh do I need this!! I have been trying to remove the damaged veneer from a great antique table, but after many hours I think I will have to give up and try a new top. I want to make sure I understand……If I have a good base on the table, I just cut the board lengths I need and glue to the origianl table top? Do I need to secure the new top with screws from the bottom? I think the boards will give this table a whole new life. I can’t wait to finish it. Thank you so much for being here TODAY!


One of the best stud finders you’ll ever use is the Franklin Sensors ProSensor 710. It’s unique in that there’s a whole bar of red lights that light up whenever it detects a stud. Unlike other sensors, which have a single light that stays on as it passes over the wood, the lights on the 710 tell you exactly where the wood stops and starts. No guesswork. Push a button, drag it over the wall and those hidden mysteries reveal themselves. You won’t even need to read the directions!

Aside from the privacy it offers, a latticework porch trellis is a perfect way to add major curb appeal to your home for $100 or less. The trellis shown here is made of cedar, but any decay-resistant wood like redwood, cypress or treated pine would also be a good option. Constructed with lap joints for a flat surface and an oval cutout for elegance, it’s a far upgrade from traditional premade garden lattice. As long as you have experience working a router, this project’s complexity lies mostly in the time it takes to cut and assemble. Get the instructions complete with detailed illustrations here.
Cedar Mini Decorative Planters/Boxes Using Interlocking Dovetail Joints Having a cedar mill within an hour of my shop allows me to work with some very nice wood. While cedar can be brittle, it is wonderful to work with and makes putting these decorative boxes together a breeze. When working with cedar I am always looking for pieces that have what is known as “heartwood”. This is the red portion of the wood. When first planed or sanded, this heartwood is almost pink in color but takes polyurethane or spar finish well giving a vibrant dark red when applied. If left untreated, cedar will turn gray in direct sunlight and a dull red color from normal household light. These boxes have been treated with a wiping polyurethane mix that allows me to apply it with a cotton rag instead of a brush. It’s faster to apply, doesn’t run and dries fast enough to apply two coats in a day. So applying 5-6 coats only takes 2-3 days to accomplish. I assembled the boxes using a dovetail joint which provides both strength and decorative at the same time. A fan shaped tenon that forms a tight interlocking joint when fitted into a corresponding mortise. The dovetails on these boxes are shown on the length of the box and not the end where the handles are located. I use a dovetail jig and a router to make these joints which is more efficient. Depending on how the client will use the box I may or may not drill two holes in the bottom of the box. If they are built to be used as outside planters then I drill 2, half inch holes in the bottom for water to drain. If they are to be used inside as a table center piece or fireplace mantle decorative box, then I do not drill the hole. In the end they are strong, durable and beautiful no matter how they are used.

A magnetized screwdriver or driver bit makes starting screws a lot easier. It’s like having an extra hand to hold the screw. We also like to magnetize a screwdriver when working with tiny screws that are nearly impossible to find if you drop them (been there?). You can use a magnetic bit holder in most cases, but not in tight quarters. Instead, you can just magnetize the bit. We’ve even magnetized tweezers to help pick up tiny parts.
This could quite possibly be the best tool on this list! Have you ever tried to get your drill in a tight spot where you absolutely had to use it and just couldn’t? Holy Moly has this happened to me like 100 times. Almost nothing is more frustrating! With this flex shaft, you can bend around corners and fit into impossibly tight spaces like a knife through hot butter! Buy this thing!!!!
The Bosch Max FlexiClick 5-in-1 Drill/Driver System has one tool and five attachments. That means it can perform all kinds of tasks, like: screw-driving, drilling, right angle drilling/driving and offset driving close to edges. This tool/tools isn’t going to replace a deck builder’s 20v impact driver and drill, but it might be a great option for those smaller project that require a bunch of different operations, like knocking off a punch list at the end of a build-out. If you’re moving around and don’t have the space to haul around a bunch of dedicated tools this might be just what you’re looking for. The Bosch 5-in-1 Drill Driver System is available online and in home centers for $199.00.
Every student requires help with homework from time to time. Somebody works part-time and doesn’t have enough time to do all the assignments. Others are not good writing essays and always experience difficulties when they have to complete one more paper. Sometimes, even the best students become too exhausted and don’t have enough energy to write a quality paper. In such moments everybody needs a little help, and Homeworkfor.me is always ready to lend a hand with any academic problem.

The Milwaukee REDSTICK can be used to screed, smooth, and level. Once you’re done, the level is preposterously easy to wipe clean. The REDSTICK also has all the great features you would expect from a Milwaukee level. SHARPSITE Vial Technology makes the magnified bubble easy to read and the REDSTICK’s magnesium core keeps the level from breaking down. The Milwaukee REDSTICK Concrete Levels are available in 24-in., 48-in. and 72-in. lengths starting at $99.99.
Slice, dice and serve in style on this easy, attractive board. We’ll show you a simple way to dry-fit the parts, scribe the arc and then glue the whole thing together. We used a 4-ft. steel ruler to scribe the arcs, but a yardstick or any thin board would also work. Find complete how-to instructions on this woodworking crafts project here. Also, be sure to use water-resistant wood glue and keep your board out of the dishwasher or it might fall apart. And one more thing: Keep the boards as even as possible during glue-up to minimize sanding later. For great tips on gluing wood, check out this collection. 

I had been looking forward to this part—applying the Minwax Gel Stain. First, I tested the stains on a leftover board to confirm my suspicion that, used together, the three stains would complement one another perfectly. When the test confirmed my suspicions, I proceeded to stir each stain until it developed a creamy, smooth consistency—nothing like the watery liquid you might be used to. With its thicker formulation, Minwax Gel Stain has been specially designed to be user-friendly and easy to apply. With either a foam brush or a rag, the Gel Stain goes on in a controlled way, and you don’t have to worry about drips; just let it sit on the wood for about three minutes and wipe away the excess with a rag. Once I had finished staining all the wood pieces in alternating colors—Hickory, Cherrywood, and Honey Maple—I let about eight hours of dry time elapse. Though it wasn’t strictly necessary, I decided to darken the stain colors a bit by applying a second coat, using the same technique I’d used with the first.

There are lots of clear finishes. But for a combination of usability and durability, you can’t beat polyurethane. Oil-based poly, which dries slower than water-based, is best for beginners because it allows more working time. The other important difference is clarity: Water-based poly is absolutely colorless, while oil-based has an amber tone, which can be good or bad depending on the look you want.

×