Clamp curved caul edges inwards so they align tabletop boards in the middle, then torque up the main clamps to draw the boards together. If the width of boards you’re using allow it, pre-glue boards for your tabletop in sections that are just narrow enough to fit within your thickness planer. Run these through the planer to clean and level the glue joints, then move back to clamps for final glue up. Working in stages like this reduces the number of glue joints you need to sand smooth and level later.
Bought 2 of these, one for the wife and one for me. We have a project we are doing that required cutting lots of MDF(medium density fiberboard) which is not good for you to breathe or get in your eyes (very tiny particles). I picked these because people said they worked well with glasses (which i wear) and because they had full protection from flying debris and also from the airborne dust.

Aside from this being a fun gadget to own it is one of the most versatile tools for use around the house. You can look down your garbage disposal for the ring you just dropped, inside your car engine to see where the leak is and on and on. I love to see whats clogging my gutters both in the gutter and in the drain. One of the more unique tools. It’s going to be your new favorite.

Furnishing and decorating your patio is not an easy task – but then again, it has to be done! Your patio is obviously one of the most important rooms in your home, as you can easily turn it into your little piece of Heaven, your “safe spot” in your home where you can retreat whenever you want to ignore the world and just spend some time alone all by yourself.
To save money, we keep the temp in our shop down low when we’re not in it and crank up the heat when we return. But even when the air temperature hits 70 degrees F, the concrete floor is still Minnesota-cold. We tried a space heater under the bench, but it broiled the shins and still left us with cold feet. So we recently bought a foot-warming mat, and now our feet stay toasty warm. Plus, it uses a fraction of the electricity and is a lot safer than a space heater. The mat is produced by Cozy Products. The good folks over at Cozy suggest putting a chunk of cardboard underneath it if you use it on flooring that could fade from the heat, like carpet or wood.
Adirondack Chairs in Tennessee Cedar Wood Growing up in Central New York and spending years in the Adirondack Mountains, I grew up seeing all types of Adirondack chairs. But it was not until I moved to middle Tennessee that I attempted to build Adirondack chairs myself. I found plans that gave me the basic design to build the adult chairs. I made some adjustments in order to fit them into my style and the type of wood that I have available. I found a cedar mill within an hour of my shop that allows me to purchase rough cut lumber. Because of the nature of rough lumber I am buying wood that is actually thicker, wider and longer than wood purchased at a brick front store.  Where a nominal 2”x 4”x 96” bought at a local lumber store is actually 1.5 x 3.5 x 96. The cedar I purchase is 2 ¼ x 4 ¼ x 102 inches. Once run through the surface planer to clean up the roughness and sanded, I am able to build with actual 2” x 4” or 2” x 6” lumber. This makes the chairs heavier, sturdier and more durable. Because of the size of the wood I assemble the legs and main supports with 3/8” carriage bolts. The arms, seat boards and backs are all assembled with 2” to 3” exterior screws. I predrill all the holes prior to inserting any screws. I do this because cedar, or any wood for that matter, can split at any time. The actual finished chair stands 38” tall x 39” long and 33” wide. They weigh about 35 lbs. and can seat a large adult very well but also comfortable for my tiny framed wife. The rise of the seat from the knees to the ground for your feet is 13 ½ inches. The seat reclines backward naturally but not so much that it is hard to stand from a seated position. The back is curved to support the natural curve of your back allowing for a more comfortable fit. The back is 32” tall to support even a taller person. The arms have been described as looking like whales so they are narrow where they fasten to the back of the chair and wide in the front for a cup, a book or even a laptop if you choose to work outside. *DISCLOSURE: Some of the links below are affiliate links. If you chose to click through and make a purchase I will earn a commission but there is no additional cost to you. It helps compensates the business for the time spent creating these posts. THANK YOU! Child’s Chair: The smaller child chairs are added to match the adult chairs to finish the family. These also are made with rough cedar milled and sanded to size to make the chairs sturdy. As with the adult chairs the wood will be thicker, wider and stronger than nominal wood. I use all true 1” lumber for the 
×