Keep your woodworking tools and knives razor-sharp with our wide variety of sharpening supplies and accessories. We have what you need for jointer and planer knife sharpening. For sharpening plane irons and chisels, we supply a variety of diamond and waterstones, the Infinity Sandpaper Sharpening System, and honing guides. Our power sharpening systems include the Worksharp Knife Sharpeners, Ken Onion edition for the sharpest knives in the drawer.
We will suggest you select the simple Birdhouse if you are new at woodworking but be sure to select its design with respect to the place where you are going to hang/place it. One of our simple Birdhouse tutorials will help you building one. We have managed to include a source tutorial below that will help you to understand illustrates and the instruction to building a simple Birdhouse.
Some tools required to build a picture frame are a table saw, miter saw, measuring tape, wood glue etc. A table saw with a backing board and miter gauge can be used to get the right angle and lengths of picture frame every time. You can use builders square to arrange the final cut pieces before nailing, screwing or gluing. Check out the video tutorial below for more details.

Turning over the sturdy tabletop, I felt a thrill of vindication. Clearly, it wasn’t a mistake in the end to use all three stains for the same project. Before I could consider the job done, though, I would need to apply sealer—Minwax Helmsman Spar Urethane—to protect the wood from moisture, UV rays, and the wear and tear of day-to-day life. This was my first time experimenting with a spray-application sealer, and I loved it. Obviously, it’s important to have proper ventilation in your work area, and you’ve got to shake the can vigorously before spraying, but so long as you remember the basics, spraying couldn’t be more straightforward. Holding the Helmsman Spar Urethane can about a foot from the surface, spray in a series of even strokes, always in the same direction, until you’ve completed the first coat. Let the sealer dry for about four hours before applying any additional coats, and for best results, sand the entire surface before each application of a new layer.
Using shelving in your room or kitchen is a great way to arrange and de-clutter space… I know, such ground-breaking term it is. Do not write me off yet, I just want to show you how you can build some clean floating corner shelving that appears to have no brackets. You can create them at no cost, and the hardest part of the plan is figuring out what you are going to put on these shelves when you are finished.

In stock expedited shipments will ship the same day, or the next business day for orders placed on a weekend, if the order is placed before 12 PM Central Time. Non-expedited orders are processed for shipment within two business days of payment verification, excluding holidays. You will receive a shipping confirmation e-mail once your order has shipped. The e-mail will provide your tracking number and link to the shipping carrier’s tracking page.
Photographer/filmmaker Brett Foxwell, who has expertise with both stop-motion and time-lapse techniques, created this very surprising video by shaving logs down layer-by-layer, then stitching still shots of the cross-sections together: WoodSwimmer from bfophoto on Vimeo.Writes Foxwell: I became fascinated with the possibilities of a sci-fi world based on the

The table tops are double-sided – two for one! – and are 2 feet square. The cost of the project will vary based on items you might already have but the biggest expense is the wood at about $25 – that’s $12.50 per “table” – not too shabby at all, especially when you think about the alternative of actually buying an entire table. Or the gigantic house you’d need to store all that extra furniture!
If you want your table top -- any table top -- to actually ast without bowing/cupping/twisting, you MUST attach it in a manner that allows for seasonal wood movement. Wood is an organic product, and it naturally expands and contracts with changes in temperature and humidity. I'll post link below to a couple of options that you can cheaply buy which will allow you to securely attach a tabletop while still giving the wood the flexibility to move with the seasons. When you buy decently-made furniture at a store, they all accommodate for this one way or another. Don't just screw the top down to the legs or the skirt...you'll regret it later on.
The next part of the custom woodworking transaction is a visitation to the actual site where the furniture is going to be placed. The woodworker determines if the design is doable. If it is, he advises the client of the final cost. Once the design is approved and the contract is signed, the construction of the project can begin. Some woodworkers require advance payment before the construction can commence.
This DIY has a bit of a backstory: In my basement workshop—as a byproduct of about a half dozen previous projects—I’d managed to accumulate a small mountain of scrap wood. Though the pieces varied in size, most were 2×4 boards. For weeks, I pondered the question of how to use them. There wasn’t enough material to build anything substantial, but at the same time, this was much more wood than I would feel comfortable chucking or committing to kindling. I suddenly seized on the idea of turning those leftover boards into a rustic tabletop, but then I let the project momentum slow to a creep, and in the blink of an eye another few weeks had gone zooming by. Things finally came to a head one day when I was scanning the local giveaway listings. There, I discovered that one of my neighbors was trying to get rid of an old metal garden table. Upon seeing the pictures, I knew immediately that this would be a great table to top with the scrap wood surface I’d been planning to make with all those 2x4s!
Let’s start with perhaps the most basic tool in every household – the claw hammer. The claw on one side of the head should be well counterbalanced by the finished head, which should be somewhat rounded. The other kind of head is the waffle-head. Most commonly used in construction, it leaves a distinctive waffle mark on the wood when you drive the nail. This, of course, is not the proper nail for woodworking.
The table tops are double-sided – two for one! – and are 2 feet square. The cost of the project will vary based on items you might already have but the biggest expense is the wood at about $25 – that’s $12.50 per “table” – not too shabby at all, especially when you think about the alternative of actually buying an entire table. Or the gigantic house you’d need to store all that extra furniture!
Building a table is one of the most deceptively simple woodworking projects going. What could be easier than gluing up a few boards and applying a finish, right? But reality is often surprising, because building a top for that table can go wrong in ways you might not realize until it’s too late.  Here are my favourite tabletop construction tips, plus advice on how to avoid trouble. 

Ridgid has a new C-style close-quarter tubing cutter that slices through both 1/2-in. and 3/4-in. tubing, which means one less tool to carry and fumble around for. The cutting wheel is spring loaded so it needs no adjustment as you spin the cutter, and the outside surface has screwdriver slots for getting leverage in tight spaces. The 1/2 – 3/4 Rigid tubing cutter costs $32 and is available at plumbing supply stores and online retailers.
She has permanently glued and screwed the tabletop within that four-sided, mitered frame. Attaching the skirt to the long edges of the wide boards is no problem, but fastening them to the end grain of the wide boards, as shown in the photo above, is. The builder has constricted the wide boards' movement, and as they grow or shrink in width but are held in place by those end-caps, they will warp and split, making this a short-lived piece of furniture.
It is becoming more popular in this DIY age for people to want to make things themselves, and we are seeing a return to woodworking as a hobby or pastime. The garage is transformed into a workshop, with a workbench a set of woodworking tools and of course a beer fridge. Beautiful handmade woodworking projects can be achieved with some practice, a good set of plans and the right woodworking tools.
This could quite possibly be the best tool on this list! Have you ever tried to get your drill in a tight spot where you absolutely had to use it and just couldn’t? Holy Moly has this happened to me like 100 times. Almost nothing is more frustrating! With this flex shaft, you can bend around corners and fit into impossibly tight spaces like a knife through hot butter! Buy this thing!!!!
If you sand through the polyurethane and remove some stain, you can touch up with more stain. But the repair won’t be perfect, so take pains to avoid that mistake. Sand very lightly after the first coat, just enough to remove the dust whiskers. After the second coat, you can sand a little harder to flatten larger flaws. Always be careful around the edges of the table; that’s where it’s easiest to sand through.
If you’re like me, every time you wander through a big-box furniture store, you feel a little insulted. Here you are, a man, staring at relatively simple furniture, being asked to lay down large sums of money for a bookshelf, dining set, or desk. And if you know enough about wood to spot laminate and fiberboard, you’ll quickly see these expensive pieces of furniture have a shelf life (no pun intended) of about two years.
The best thing about the toy chest is that it is very easy to build. All you need is the basic understanding of woodworking and a few tools to get started. You can also modify your kid’s toy chest in any way you want or build in a different design or color different from the one pictured above. You can try some other designs for your plan in the below-mentioned link.
ClickBank is the retailer of products on this site. CLICKBANK® is a registered trademark of Click Sales, Inc., a Delaware corporation located at 917 S. Lusk Street, Suite 200, Boise Idaho, 83706, USA and used by permission. ClickBank's role as retailer does not constitute an endorsement, approval or review of these products or any claim, statement or opinion used in promotion of these products.
As with most websites, we do log web visits. This information, however, does not have a link to you personally. These logs help us understand the needs of our audience and the areas of our site that you do or do not find useful. When you simply browse our site, no personal information is being collected.  We may disclose this non-personal information to third parties such as sponsors, clients or advertisers.
What makes this JCB Teleskid machine unique is it’s one-of-a-kind telescoping boom, which gives it the ability to reach a variety of places. The Teleskid’s telescoping boom gives you eight feet of outward reach. Plus, its one armed design gives you 60 percent more visibility than similar twin-armed machines. With a fully extended boom the Teleskid can lift up to 1600 pounds. With the boom retracted that weight capacity goes up to an impressive 3695 pounds. To find out more about the Teleskid from JCB, click here.
I’ve been doing a lot of remodeling on my house and this wristband has come in pretty handy. The magnets work very well and able to hold all the screws, washers, and bolts for the different projects I’m working on. The pockets are a great addition too for holding plastic items. In fact, I found it useful for holding a small pencil where I can have quick access to for marking measurements for cuts. Overall it’s a great quality wristband and would definitely recommend.

Hey Cara – We bought MinWax wooden stain in Cherry (the teeny, tiny can) and one other color, but it has been misplaced in the garage somewhere. We picked up sample sized containers of paint in Satin finish (we bought them at Lowe’s so it was Olympic brand). I just found pretty blue and dark red paint chips and the paint counter guy did the rest! Hope that helps – happy to answer questions if you need any more info

Simply brilliant. Why didn’t I think of this? So we have a nearly 100 year old house. There is always something that needs repair. Thanks to whoever invented this little guy! No more mouth full of nails or screws. No more climbing up and down the ladder to get the damn screwdriver I dropped. Probably won’t hold your 16 oz claw hammer but other than that it is perfect. I love this. Highly recommend. Thanks for reading

If you have some basic carpentry and tool usage skills, take advantage of Ryan's custom woodworking plans and the opportunity to build a custom entertainment center yourself with entertainment center plans, media center plans and woodworking plans designed and published by Ryan. If you don't, now is a great time to start. Its not as difficult as your may think.


Hey Cara – We bought MinWax wooden stain in Cherry (the teeny, tiny can) and one other color, but it has been misplaced in the garage somewhere. We picked up sample sized containers of paint in Satin finish (we bought them at Lowe’s so it was Olympic brand). I just found pretty blue and dark red paint chips and the paint counter guy did the rest! Hope that helps – happy to answer questions if you need any more info 

Diablo's 6-piece Starter Bit Set includes a variety Diablo's 6-piece Starter Bit Set includes a variety of profiles ideal for the beginning woodworker. Featuring TiCo carbide with titanium these bits provide a long cutting life and ultra-fine finish. Perma-Shield Diablo's high performance coating reduces friction and build-up on the bits. The bits kick-back reducing design allows for safer ...  More + Product Details Close
Turning over the sturdy tabletop, I felt a thrill of vindication. Clearly, it wasn’t a mistake in the end to use all three stains for the same project. Before I could consider the job done, though, I would need to apply sealer—Minwax Helmsman Spar Urethane—to protect the wood from moisture, UV rays, and the wear and tear of day-to-day life. This was my first time experimenting with a spray-application sealer, and I loved it. Obviously, it’s important to have proper ventilation in your work area, and you’ve got to shake the can vigorously before spraying, but so long as you remember the basics, spraying couldn’t be more straightforward. Holding the Helmsman Spar Urethane can about a foot from the surface, spray in a series of even strokes, always in the same direction, until you’ve completed the first coat. Let the sealer dry for about four hours before applying any additional coats, and for best results, sand the entire surface before each application of a new layer.
This was not actually a tutorial post to the woodworking plan ideas but the aim of the post was to give some easy and free woodworking ideas to the readers. If you have some time to entertain yourself and also willing to add some new stuff to your furniture you can take any idea from the list and start working on it. Be sure to see both post tutorial and video tutorials of the plan you have selected, it will make you understand everything nicely.
This is another very interesting project. To make a similar table you need to have textured spray paint, matte black spray paint, lumber, wood boards, wheels, stain, sand paper, corner pieces, nails, bolts, nuts, washers, clamps and L brackets. First make the measurements and spray paint all the hardware including the wheels. Then make the basic box and sue nails to hold the wood pieces in place. Then use L brackets to keep them sturdy and add the bolts. Tighten the nuts into the bolts and attach the wheels.Then add the corner pieces sing nails{found on theblissfulbeeblog}.
Check out our most recent woodworking tools and accessory reviews below. We have thousands of satisfied customers that use our router bits, shaper cutters, router tables, and many more fine woodworking tools every day. Take a minute to read what your fellow woodworkers have to say about their experience with our company and our quality woodworking tools. All reviews are from real customers of Infinity Tools who were polled by our partners at ShopperApproved.com. More third party reviews can be found at Shopper Approved's website.
She has permanently glued and screwed the tabletop within that four-sided, mitered frame. Attaching the skirt to the long edges of the wide boards is no problem, but fastening them to the end grain of the wide boards, as shown in the photo above, is. The builder has constricted the wide boards' movement, and as they grow or shrink in width but are held in place by those end-caps, they will warp and split, making this a short-lived piece of furniture. 

Rachel Teodoro and Holy-Craft.com, 2010-present. Unauthorized use and/or duplication of this material without express and written permission from this site’s author and/or owner is strictly prohibited. Excerpts and links may be used and up to one photo can posted, provided that full and clear credit is given to Rachel Teodoro and Holy Craft with appropriate and specific direction to the original content.

Personally identifying information is information that can be used to identify who you are such as: name, mailing address, email address. To enter certain areas of the site, you will be required to register and provide information about yourself. This information is for the purposes of Canadian Woodworking and helps us to tailor the site to best meet the needs of our audience. 
There are lots of clear finishes. But for a combination of usability and durability, you can’t beat polyurethane. Oil-based poly, which dries slower than water-based, is best for beginners because it allows more working time. The other important difference is clarity: Water-based poly is absolutely colorless, while oil-based has an amber tone, which can be good or bad depending on the look you want.

With a pencil and a protractor, divide the larger disc into 30-degree wedges to create 12 center lines for the bottle indents. Center and trace the smaller disc on top of the larger disc. Next, with a drill press, drill 3/8-in.-deep holes on the 12 center lines with the 1-7/8-in. Forstner bit, spacing them between the disc’s outer edge and the traced circle. Next, divide the smaller disc into 60-degree wedges and drill six more 3/8-in.-deep holes with the Forstner bit.
I started by doing some searches around the ol’ internet to find other folks who’ve built their own tables. Using the images and information I found, I started drawing up plans. My table is approximately 6’x44″x31″ (LxWxH). You may find different dimensions work better for you (31″ is pretty tall)–so make your plans however you like. I also built leaves that make the table 8.5’ long.
Copyright 2018 by Cut The Wood. CutTheWood.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Additionally, CutTheWood.com participates in various other affiliate programs, and we sometimes get a commission through purchases made through our links.
Do you have older 18V DeWalt tools that are still near and dear to your heart but need new batteries? Consider firing up those old tools with 21st century technology. Now, 18V tools can be run on powerful 20V lithium Ion batteries with DeWalt’s new battery adapter. The adapter slides into the tool and the battery hooks onto the adapter. It works on most 18V DeWalt tools but not all. It’s sold two ways: the adapter alone (DCA1820), or the adapter with two compact 20V, 2.OAh batteries and charger. Now you’ll be able to hold on to your favorite cordless reciprocating saw forever!
We call them strongbacks and we use them on every tabletop we build. It's just a scrap strip of 3/4" plywood, with 3/4" pocket holes drilled about ever few inches. The strongback is attached to the bottom of the tabletop as the glue dries. The square edge of the plywood prevents the tabletop from warping or cupping as it dries. Then we remove the strongbacks (and save them for the next tabletop) when we attach the tabletop to the base.
This could quite possibly be the best tool on this list! Have you ever tried to get your drill in a tight spot where you absolutely had to use it and just couldn’t? Holy Moly has this happened to me like 100 times. Almost nothing is more frustrating! With this flex shaft, you can bend around corners and fit into impossibly tight spaces like a knife through hot butter! Buy this thing!!!!
Finding the right diy woodworkers project ideas via the internet is simple if you know where to look. If you are a beginner, you might want to look for packages that provide a huge variety ofoptions. The best ones will include clear instructions, text, diagrams, and tips. A good online plan will help you learn the skills you need much more quickly, so you can maintain speed and keep making fun projects.

Now that you have the tools, you can build anything you want whenever you want at a fraction of the cost. Install molding, update your window casings and trimwork, build a custom closet, some laundry room shelves or whatever! Not to mention, now you can start making gifts for friends and family or building a small business. The opportunities are set by your imagination.


As your interest in woodworking grows, you’ll want to subscribe to a woodworking magazine. This will help feed your new found obsession with articles on tools, techniques, and woodworking plans. As a print magazine subscriber you’ll also gain access to their database of plans on their websites. Popular magazines include, Woodworkers Journal, Fine Woodworking, and Popular Woodworking.
One of the best stud finders you’ll ever use is the Franklin Sensors ProSensor 710. It’s unique in that there’s a whole bar of red lights that light up whenever it detects a stud. Unlike other sensors, which have a single light that stays on as it passes over the wood, the lights on the 710 tell you exactly where the wood stops and starts. No guesswork. Push a button, drag it over the wall and those hidden mysteries reveal themselves. You won’t even need to read the directions!
Behind every great woodworking piece is a great woodworking plan. Even the classic furniture makers of the 18th and 19th centuries worked from detailed precision drawn plans. This is how we are able to make such genuine looking reproductions of the works of the famous furniture makers of old; the master woodworker’s plans are still extant. Many different styles and designs are available, from all different periods in history, to modern designs from this century. Working with the right woodworking tools a skilled woodworker can make any piece of furniture; however fancy the detail is, if he has an accurate woodworking plan to work from. Once you have reached a certain skill level in your woodworking techniques, you will be able to create a masterpiece which can be handed down through your family for future generations.
There are lots of clear finishes. But for a combination of usability and durability, you can’t beat polyurethane. Oil-based poly, which dries slower than water-based, is best for beginners because it allows more working time. The other important difference is clarity: Water-based poly is absolutely colorless, while oil-based has an amber tone, which can be good or bad depending on the look you want.
Some tools required to build a picture frame are a table saw, miter saw, measuring tape, wood glue etc. A table saw with a backing board and miter gauge can be used to get the right angle and lengths of picture frame every time. You can use builders square to arrange the final cut pieces before nailing, screwing or gluing. Check out the video tutorial below for more details.
​Luckily, we have also managed to find a detailed video tutorial of the Barn door project that illustrates the process of building a Barn door of your own. The steps and instructions in the video tutorial are different from the source links listed above. Actually, you can make different types of designs for your Barn door depending on which one you can afford easily and DIY on your own.

Look at the amazing masterpiece Domestic Imperfection made out of her plain Jane dining table!  Using a stencil and white paint, you can create this design or similar, then tone it down and make it look slightly aged by staining the wood right over the top of the painted design!  Very clever stenciled and stained table redo. // Domestic Imperfection


Drill pocket holes from the outer boards to the inner board. Drilling the holes before adding screws prevents the boards from cracking. To create the holes, measure along the sides of the center board. Mark it about every 7 in (18 cm). You will need to use a very long drill bit, about 3 in (7.6 cm) wide, called a pocket hole drill bit. Drill at an angle down through the side boards and into the side of the center board every 7 in (18 cm).[4]
Personally identifying information is information that can be used to identify who you are such as: name, mailing address, email address. To enter certain areas of the site, you will be required to register and provide information about yourself. This information is for the purposes of Canadian Woodworking and helps us to tailor the site to best meet the needs of our audience. 
For this project you need a table base. An old table with no top would be perfect. The idea is to create a new wood top with an original design. Since this project is for an outdoor table, you can also include an ice bucket in the middle. Find some large pieces of wood and put them together to make a top. Make a hole for the bucket if you want one and insert it. Then, to make the edges of the table, use a belt sander. Get creative until you’re happy with the results and, at the end, stain the table.{found on thehuntedinterior}.
Just redid my dining room table with this technique and I an observation/suggestion others might find helpful. The boards did not line up well putting it together upside down, even on a flat concrete floor with me standing on the boards while they were screwed. I would have combined biscuits with the pocket holes to ensure a better alignment of the boards. Lots of sanding was required after assembly, and this might not be a huge deal with pine, but I used hard maple so it was quite a chore even with a belt sander. Also, be aware that the 1x2s around the edge may not line up perfectly -- I had to trim about an eighth inch from each side after assembly to get nice smooth, even edges. Not a big deal, but the top turned out a little smaller than the specifications I was give by SheWhoMustBeObeyed. Otherwise our table now looks great, and thank you for the post!
Hanging upper cabinets is a tough task for one person. Having a lifting buddy to help is usually a good idea but costs extra. Little Hands HD is perfect for the guy who mostly works alone. The 6 x 6-in. base keeps the cabinets stable, and each lift can handle 150 lbs. The lever action can be raised a tiny fraction of an inch at a time, but sneak up on your target height because lowering the lifts isn’t quite as easy.

If you have some basic carpentry and tool usage skills, take advantage of Ryan's custom woodworking plans and the opportunity to build a custom entertainment center yourself with entertainment center plans, media center plans and woodworking plans designed and published by Ryan. If you don't, now is a great time to start. Its not as difficult as your may think.
After you've used one of these free coffee table plans to build your dream coffee table, check out these other free woodworking plans for bookcases, TV stands, dressers, nightstands, step stools, entertainment centers, farmhouse tables, desks, jewelry boxes, dining room tables, wine racks, picnic tables, kitchen islands, home bars, bunk beds, toy boxes, and even dog houses.

Google is probably the first place where most people would start searching for woodworking plans, but often the top results can be a mix of articles and how-to pieces that just aren’t detailed enough. Sometimes they’ll link to the plans (like we try to here at Lifehacker), but other times, they’re just showing off a cool project. There are better, more precise ways of finding what you’re looking for.


Diablo's 6-piece Starter Bit Set includes a variety Diablo's 6-piece Starter Bit Set includes a variety of profiles ideal for the beginning woodworker. Featuring TiCo carbide with titanium these bits provide a long cutting life and ultra-fine finish. Perma-Shield Diablo's high performance coating reduces friction and build-up on the bits. The bits kick-back reducing design allows for safer ...  More + Product Details Close


What makes this JCB Teleskid machine unique is it’s one-of-a-kind telescoping boom, which gives it the ability to reach a variety of places. The Teleskid’s telescoping boom gives you eight feet of outward reach. Plus, its one armed design gives you 60 percent more visibility than similar twin-armed machines. With a fully extended boom the Teleskid can lift up to 1600 pounds. With the boom retracted that weight capacity goes up to an impressive 3695 pounds. To find out more about the Teleskid from JCB, click here.
This is a well built bag that does a good job of consolidating tools. It opens up very wide and is surprisingly compact when closed. I use mine doing HVAC installation to avoid schlepping power tools one at a time. Holds a circular saw, reciprocating saw, angle grinder, hammer drill and the associated bits/discs/blades/batteries/grips. Also have a two foot level and 18" bar folder in there and it still zips closed with zero issues.
Clean wooden gutters of any loose debris and cut to a manageable length. Miter down to form an approximately 40" x 94" rectangle. Coat the corners with wood glue and fasten together with 15-gauge finish nails. If miters are tight 45-degree cuts, box should be square. Double check diagonal measurements before fastening completely. The two diagonal measurements should be as close to equal as possible.
These unique clamps will save you time and aggravation in too many ways to list! MatchFit clamps slide anywhere along a groove routed with a common 1/2" - 14 degree dovetail bit and leave one surface of your work clear of obstructions. Use these clamps to create customizable clamping tables and for attaching table extensions, sub fences, stop blocks, hold downs, and more to your machinery and work tables. Imported.
It is becoming more popular in this DIY age for people to want to make things themselves, and we are seeing a return to woodworking as a hobby or pastime. The garage is transformed into a workshop, with a workbench a set of woodworking tools and of course a beer fridge. Beautiful handmade woodworking projects can be achieved with some practice, a good set of plans and the right woodworking tools.

If you can beg or borrow a pocket hole jig you dont have to predrill holes. I haven’t done a table top other than a workbench(Plywood!) but I have done cabinets and beds. The Kreg jig makes joining easy. A lighter stain colour would cut down on the grain marks, or a heavier application like an espresso stain. I will throw you a pic when I finish my table and show you what I mean.


For starters, this DIY wood table is for my son to keep his Lego projects and erector set buildings on. Secretly, it’s for me because, in turn, it will keep the Legos from being scattered all over my house. We decided on measurements of 60″ long x 18″ deep for the table top. Now that I know how big I want our homemade table to be I reached out to Osborne Wood Products to find out what the next step is for building a table. They were super helpful and made it very easy to order the table base kit. We let them know the measurements for the table top as well as how much of an overhang. We then choose the traditional dining table legs in soft maple along with a 4″ wood skirt also in soft maple. The furniture kit came well packaged and rather quickly. 
No sadly, as I mentioned above, my table top ended up splitting, starting at a knot on the edge and going clear across the top (pre-drill those holes!!!), so I had to come up with another solution.  I didn’t want to go to the trouble of making another table top like this one, so I did a much easier and quicker solution…stain-grade plywood with decorative moulding attached to the edges. 
Rolled-on poly looks terrible at first, but the bubbles disappear in minutes, leaving a smoother surface than most of us can achieve with a brush. Beware of ridges formed by the edges of the roller and humps where you start and stop. You can minimize both of those flaws by applying lighter coats. We experimented with several kinds of rollers and got the best results with microfiber mini rollers. We also tried rolling on water-based poly; don’t do it.
Hanging upper cabinets is a tough task for one person. Having a lifting buddy to help is usually a good idea but costs extra. Little Hands HD is perfect for the guy who mostly works alone. The 6 x 6-in. base keeps the cabinets stable, and each lift can handle 150 lbs. The lever action can be raised a tiny fraction of an inch at a time, but sneak up on your target height because lowering the lifts isn’t quite as easy.
This time I surprised one of my favorite dice games and took it outside. I made a set of wooden dice in just a few hours, and instead of sitting in the room and doing nothing, we are taking our dice game out into the yard. With this set of wooden dice, dice games are becoming our favorite backyard game. Check out the step by step tutorial below so you can make your own.
×