There is no cost to use the database. Registering is not required. You should be able to browse the database and click through the links. Having said that, considering the fact there are so many browsers out there being used, this site's software might not allow some visitors to browse, it all depends on the Internet traffic, and your browser's compatibility.
Oh do I need this!! I have been trying to remove the damaged veneer from a great antique table, but after many hours I think I will have to give up and try a new top. I want to make sure I understand……If I have a good base on the table, I just cut the board lengths I need and glue to the origianl table top? Do I need to secure the new top with screws from the bottom? I think the boards will give this table a whole new life. I can’t wait to finish it. Thank you so much for being here TODAY!

Aside from the privacy it offers, a latticework porch trellis is a perfect way to add major curb appeal to your home for $100 or less. The trellis shown here is made of cedar, but any decay-resistant wood like redwood, cypress or treated pine would also be a good option. Constructed with lap joints for a flat surface and an oval cutout for elegance, it’s a far upgrade from traditional premade garden lattice. As long as you have experience working a router, this project’s complexity lies mostly in the time it takes to cut and assemble. Get the instructions complete with detailed illustrations here.
There’s a lot of space above the shelf in most closets. Even though it’s a little hard to reach, it’s a great place to store seldom-used items. Make use of this wasted space by adding a second shelf above the existing one. Buy enough closet shelving material to match the length of the existing shelf plus enough for two end supports and middle supports over each bracket. Twelve-inch-wide shelving is available in various lengths and finishes at home centers and lumberyards. 

Relax and enjoy your outdoor space with this smart patio combo consisting of a sofa and chair. You can adjust the size completely to make it fit perfectly onto your patio or deck, and both the sofa and chair have arms that double as trays for al fresco dining. And you can make your own cushions to fit, or use shop-bought ones and add your own ties, if necessary.
This could quite possibly be the best tool on this list! Have you ever tried to get your drill in a tight spot where you absolutely had to use it and just couldn’t? Holy Moly has this happened to me like 100 times. Almost nothing is more frustrating! With this flex shaft, you can bend around corners and fit into impossibly tight spaces like a knife through hot butter! Buy this thing!!!!
Ridgid has a new C-style close-quarter tubing cutter that slices through both 1/2-in. and 3/4-in. tubing, which means one less tool to carry and fumble around for. The cutting wheel is spring loaded so it needs no adjustment as you spin the cutter, and the outside surface has screwdriver slots for getting leverage in tight spaces. The 1/2 – 3/4 Rigid tubing cutter costs $32 and is available at plumbing supply stores and online retailers.

Drill four 5/8-in.-dia. 1/2-in.-deep holes on the large disc?inside the traced circle?then use 5/8-in. dowel centers to transfer the hole locations to the underside of the small disc. Drill four 1/2-in.-deep holes on the underside of the small disc and a 1/2-in.-deep hole in the center of the top for the dowel handle. Glue in the dowels to join the discs, and glue in the handle. We drilled a wood ball for a handle knob, but a screw-on ceramic knob also provides a comfortable, attractive grip.


For starters, this DIY wood table is for my son to keep his Lego projects and erector set buildings on. Secretly, it’s for me because, in turn, it will keep the Legos from being scattered all over my house. We decided on measurements of 60″ long x 18″ deep for the table top. Now that I know how big I want our homemade table to be I reached out to Osborne Wood Products to find out what the next step is for building a table. They were super helpful and made it very easy to order the table base kit. We let them know the measurements for the table top as well as how much of an overhang. We then choose the traditional dining table legs in soft maple along with a 4″ wood skirt also in soft maple. The furniture kit came well packaged and rather quickly. 
The engineering involved in building this garden bench is pretty simple, and we have provided some links to get a full cut list and plans with photos to help you along the way. Additionally, to the stock lumber, you will need wood screws, barrel locks, and hinges to complete the table. A miter saw or hand saw is also extremely helpful for cutting down your stock to the correct angle and length.

We recently upgraded a wheelbarrow with Simply Dump It pivoting handles. They slid right over the handles and took about five minutes to install. If you’re tall, you probably hunch over when you roll your wheelbarrow around the yard so you don’t end up nose-diving the wheel guard/brace into the ground, resulting in messy spills and the occasional expletive. The Simply Dump It handles raise the grip location a few inches, which lowers the handles, which in turn raises the front wheel brace. The handles not only prevent sudden stopping syndrome but also make the wheelbarrow easier to control, especially on rough terrain. And the pivoting action all but eliminates the awkward torque on your wrists when you empty the wheelbarrow. You can get Simply Dump It handles online.


Hey Cara – We bought MinWax wooden stain in Cherry (the teeny, tiny can) and one other color, but it has been misplaced in the garage somewhere. We picked up sample sized containers of paint in Satin finish (we bought them at Lowe’s so it was Olympic brand). I just found pretty blue and dark red paint chips and the paint counter guy did the rest! Hope that helps – happy to answer questions if you need any more info
Everybody has a home remedy for sealing partially used tubes of caulk. But what if you had a single product that could seal caulk cartridges, squeeze tubes, glue bottles, felt-tip pens and anything else that has a nozzle? Well, these Little Red Nozzle Caps are just the ticket. Roll the cap down the nozzle to seal out dirt and preserve the remainder of the bottle, tube or cartridge.
Okay, let’s stain this beast. I should explain that we used Rustoleum’s Dark Walnut Ultimate Wood Stain, but we did it wrong. We failed to mix it well before applying it, resulting in a color we really liked–but not the color this stain is designed to create. When we came back to do a second coat, we stirred it well, resulting in a coat that looked like purple paint. I had to sand it off and start over. So, don’t follow my lead here–follow the can’s directions and TEST before staining all of your new masterpiece!
Copyright 2018 by Cut The Wood. CutTheWood.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Additionally, CutTheWood.com participates in various other affiliate programs, and we sometimes get a commission through purchases made through our links.
Be sure wood is dry. Material from a job site or floor joists that existed in a crawlspace may have high moisture content; material from a conditioned space should be dry. Wood can be dried in a kiln (ask your local lumber mill) or stored inside through the winter. If time does not permit, stack wood in a hot dry place with 1" spacers between layers. Allow to dry for a minimum of two weeks.
What makes this JCB Teleskid machine unique is it’s one-of-a-kind telescoping boom, which gives it the ability to reach a variety of places. The Teleskid’s telescoping boom gives you eight feet of outward reach. Plus, its one armed design gives you 60 percent more visibility than similar twin-armed machines. With a fully extended boom the Teleskid can lift up to 1600 pounds. With the boom retracted that weight capacity goes up to an impressive 3695 pounds. To find out more about the Teleskid from JCB, click here.
​Luckily, we have also managed to find a detailed video tutorial of the Barn door project that illustrates the process of building a Barn door of your own. The steps and instructions in the video tutorial are different from the source links listed above. Actually, you can make different types of designs for your Barn door depending on which one you can afford easily and DIY on your own.

I've worn this apron in my studio/workshop several times now, and I really like it. It's more expensive than some, but the materials and construction are first-rate. I rarely give five stars, but the workmanship on this apron is impressive. The fabric is substantial and, although a bit stiff at present, comfortable to wear. The strap and grommet system is pretty clever, allowing a good fit for most, I would think. I'm a 5'-7" not-skinny woman, and I'm able to cross the straps at the small of my back and then tie them in front, so I'm guessing there would be plenty of strap length for bigger men. The straps sit comfortably on my shoulders. And all the pockets are great!


There are lots of clear finishes. But for a combination of usability and durability, you can’t beat polyurethane. Oil-based poly, which dries slower than water-based, is best for beginners because it allows more working time. The other important difference is clarity: Water-based poly is absolutely colorless, while oil-based has an amber tone, which can be good or bad depending on the look you want.
×