The most commonly purchased claw hammer is the 20 oz. size. It’s heavy enough to easily drive nails but easily manipulated when pulling nails. While wooden handles are picturesque, they may not stand up to the strain if you have to pull a lot of nails. Hammers with a steel handle, or even fiberglass, will be stronger. However, these won’t absorb the vibrations from driving nails the way a hickory handle will. You’ll also need to make sure the fiberglass and metal handles have a rubberized grip for control and comfort. If you’re going to be driving a lot of nails, the wooden handled hammer will be better for reducing stress on your hand, and wrist, too.
This time I surprised one of my favorite dice games and took it outside. I made a set of wooden dice in just a few hours, and instead of sitting in the room and doing nothing, we are taking our dice game out into the yard. With this set of wooden dice, dice games are becoming our favorite backyard game. Check out the step by step tutorial below so you can make your own.
Woodworking power tools include various saws for cutting the wood to size and drills for creating holes. Sand pieces down to the finish you want before you sand with portable sanders. Use drivers to install woodworking fasteners for a durable final piece. Cleverly designed rotary tools feature removable bits that can drill, drive, sand, cut and more, so you can use a single tool to accomplish virtually every task of your project. For a production-level project, nail guns can save you hours or even days depending on the work involved.
Photographer/filmmaker Brett Foxwell, who has expertise with both stop-motion and time-lapse techniques, created this very surprising video by shaving logs down layer-by-layer, then stitching still shots of the cross-sections together: WoodSwimmer from bfophoto on Vimeo.Writes Foxwell: I became fascinated with the possibilities of a sci-fi world based on the
This time I surprised one of my favorite dice games and took it outside. I made a set of wooden dice in just a few hours, and instead of sitting in the room and doing nothing, we are taking our dice game out into the yard. With this set of wooden dice, dice games are becoming our favorite backyard game. Check out the step by step tutorial below so you can make your own.
Example Entertainment Center: $25 for plans + $750 for materials + $1200 for good quality tools = $1975. Less than a few grand! Of course you don't have to buy brand new tools; search the sale lists online (i.e. Craigslist, Freecycle.org, etc.) in your area. You are sure to find some good deals on power tools and even materials! (A good set of tools includes a table saw, miter saw, nail gun and compressor and four piece cordless tool set.)

Slice, dice and serve in style on this easy, attractive board. We’ll show you a simple way to dry-fit the parts, scribe the arc and then glue the whole thing together. We used a 4-ft. steel ruler to scribe the arcs, but a yardstick or any thin board would also work. Find complete how-to instructions on this woodworking crafts project here. Also, be sure to use water-resistant wood glue and keep your board out of the dishwasher or it might fall apart. And one more thing: Keep the boards as even as possible during glue-up to minimize sanding later. For great tips on gluing wood, check out this collection.


Online packages also allow you to build at a convenient pace, whether you want to build one bench per week or want to try every new furniture plan available – and more importantly, the use of clear instructions will enable you to build under a comfortable environment without any pressure. That way, you do not face disappointment that you would otherwise experience if you buy hard-to-understand furniture plans or can’t find the specific project that you’re looking for. If you think that a plan outline is simple, you can find a more difficult one and begin practicing new skills and techniques. That way, you are able to build more things faster than if you bought each plan individually and had to search for it each time.


When you buy the wood, look for pieces that aren’t warped, excessively longer or shorter than the others, and, if you can get lucky, don’t carry the telltale “new wood” planer marks. We purchased the most inexpensive wood that we could find. You’ll likely find them in 2- and 4-ft pieces. If you have a saw at home, you might consider getting the 4 ft pieces to decrease the cost of your project a bit.
Diablo's 6-piece Starter Bit Set includes a variety Diablo's 6-piece Starter Bit Set includes a variety of profiles ideal for the beginning woodworker. Featuring TiCo carbide with titanium these bits provide a long cutting life and ultra-fine finish. Perma-Shield Diablo's high performance coating reduces friction and build-up on the bits. The bits kick-back reducing design allows for safer ...  More + Product Details Close
By completing a form on this website, you will be able to receive email correspondence from Canadian Woodworking.   These emails may include information on upcoming events or special offers for subscribers. If you do not wish to receive email correspondence please email orderdesk@canadianwoodworking.com  and ask to be removed from our email list. Every email that we send to you will include an "opt-out" from receiving future email correspondence. 
I've worn this apron in my studio/workshop several times now, and I really like it. It's more expensive than some, but the materials and construction are first-rate. I rarely give five stars, but the workmanship on this apron is impressive. The fabric is substantial and, although a bit stiff at present, comfortable to wear. The strap and grommet system is pretty clever, allowing a good fit for most, I would think. I'm a 5'-7" not-skinny woman, and I'm able to cross the straps at the small of my back and then tie them in front, so I'm guessing there would be plenty of strap length for bigger men. The straps sit comfortably on my shoulders. And all the pockets are great! 

If you don’t intend to finish the wood, you can probably safely skip this step. But for me, it was crucial to sand each board, not only to ensure a level tabletop, but also to give the stain a surface to which it could easily adhere. Of course, no matter how much sanding you do, some woods (2x4s included) are not milled for finish work and may never get totally smooth. But that was fine with me, as I figured that any imperfections that remained in the end would work to underline the rustic quality of the piece. It was in that same spirit that, in the process of sanding the boards (with fine-grit paper, always in the same direction), I opted not to sand down a few of the chatter marks left by the sawmill. I knew the stain would take to the wood a bit differently in those spots than elsewhere, lending the tabletop a further layer of charm—or so I hoped. Once I was done sanding, after thoroughly cleaning each board with a moist tack cloth, I let enough time pass for the wood to dry out completely.

A super simple iPad Dock/stand made out of a single block of wood features an angled groove which gets to support the tablet device and a cut in a hole to revise access to the home button of your iPad. It’s possible to drill an access channel in the stand through which you can run a charging cable, although this mini stripped back iPad stand may have very limited functions.
​Luckily, we have also managed to find a detailed video tutorial of the Barn door project that illustrates the process of building a Barn door of your own. The steps and instructions in the video tutorial are different from the source links listed above. Actually, you can make different types of designs for your Barn door depending on which one you can afford easily and DIY on your own.
From the source tutorial, you can get illustrates to the instruction about the plan. Everything is fairly described as diagrams, images, the list of supplies and tools need etc. The process to this plan is very easy to understand and follow for if you are having some basic woodworking knowledge. Make sure to collect all the supplies you need before you start with the project. You may even ask any question directly in the comment section of the tutorial post and also comment the images of your final product if you have completed it. Either way, I hope that you will manage to build this one nicely.​
Using pocket holes to attach the stool base to the stool top prevents the top from moving during seasonal changes. It’s also not a good idea to drive screws through the edge of the apron into the table top. Over time the top could crack or the top could have enough force to push or pull the joints of the base apart. Skate over to Mistakes with Wood Can Cause Your DIY Furniture to Crack to see more about how I incorrectly attached the top on the stool.

To save money, we keep the temp in our shop down low when we’re not in it and crank up the heat when we return. But even when the air temperature hits 70 degrees F, the concrete floor is still Minnesota-cold. We tried a space heater under the bench, but it broiled the shins and still left us with cold feet. So we recently bought a foot-warming mat, and now our feet stay toasty warm. Plus, it uses a fraction of the electricity and is a lot safer than a space heater. The mat is produced by Cozy Products. The good folks over at Cozy suggest putting a chunk of cardboard underneath it if you use it on flooring that could fade from the heat, like carpet or wood.
Your monster of a table is going to be HEAVY, so I strongly recommend moving it to its final destination in two pieces–lay a blanket down in your dining room, put the top on it upside down, then the frame upside down on top of that. Attach a couple 2×4 supports across the frame for good measure, then begin the frustrating process of centering the frame on the top. Once you have the top centered, attach your brackets–I did two on each end and three on each side.
Aside from the privacy it offers, a latticework porch trellis is a perfect way to add major curb appeal to your home for $100 or less. The trellis shown here is made of cedar, but any decay-resistant wood like redwood, cypress or treated pine would also be a good option. Constructed with lap joints for a flat surface and an oval cutout for elegance, it’s a far upgrade from traditional premade garden lattice. As long as you have experience working a router, this project’s complexity lies mostly in the time it takes to cut and assemble. Get the instructions complete with detailed illustrations here.
For starters, this DIY wood table is for my son to keep his Lego projects and erector set buildings on. Secretly, it’s for me because, in turn, it will keep the Legos from being scattered all over my house. We decided on measurements of 60″ long x 18″ deep for the table top. Now that I know how big I want our homemade table to be I reached out to Osborne Wood Products to find out what the next step is for building a table. They were super helpful and made it very easy to order the table base kit. We let them know the measurements for the table top as well as how much of an overhang. We then choose the traditional dining table legs in soft maple along with a 4″ wood skirt also in soft maple. The furniture kit came well packaged and rather quickly. 
Stanley produced this all-in-one layout tool between 1888 and the 1930s. It looks like a directional arrow from a street sign and was originally advertised as 10 tools in one (including level, depth gauge, try square, and compass). There are a few companies that make replicas, but originals can still be found on eBay for a couple hundred dollars apiece.
Even a small tabletop presents a challenge if the boards you glued together  have stepped-shaped misalignments where they meet because of warping. Yes, you can sand these off, but the more topographical sanding you need to do, the less flat and regular your finished tabletop will be. The flatter and better aligned your boards are when they’re in the clamps, the happier you’ll be later. This is where end clamps and gluing cauls can help.
Hi Mitchell – Thank you for the heads up… I thought I mentioned that in that in the post, but you’re right, I didn’t. Yes, wood expands across its width, so in order to allow for expansion/contraction there should be a small gap where the edges of the boards meet the apron. You don’t need a gap where the ends of the board meet the apron because wood doesn’t really expand/contract in this direction.
A magnetized screwdriver or driver bit makes starting screws a lot easier. It’s like having an extra hand to hold the screw. We also like to magnetize a screwdriver when working with tiny screws that are nearly impossible to find if you drop them (been there?). You can use a magnetic bit holder in most cases, but not in tight quarters. Instead, you can just magnetize the bit. We’ve even magnetized tweezers to help pick up tiny parts.
It might sound weird but you can actually turn an old window into a lovely coffee table. You just need to attach four legs and a handle and you have an original coffee table with a clever storage space inside. If the window already has the dimensions you wanted then it’s perfect. If not, you can adjust your project. You can also feel free to repaint everything.{found on ohgloryvintage}.
Google is probably the first place where most people would start searching for woodworking plans, but often the top results can be a mix of articles and how-to pieces that just aren’t detailed enough. Sometimes they’ll link to the plans (like we try to here at Lifehacker), but other times, they’re just showing off a cool project. There are better, more precise ways of finding what you’re looking for.
Breaking down heavy sheet-goods on a jobsite table saw is difficult, and dang near impossible when working alone. That’s where a track saw comes in handy. A good quality track saw can produce cabinet saw results out on any job. Now, this portable tool is even more portable. The FESTOOL TSC 55 is a cordless saw that has the same features and performs just as well as FESTOOL’s corded saw, including the cut capacity and blade speed. It also has a collection bag that actually works, collecting up to 90% of the dust. The batteries are compatible with other FESTOOL products and the saw runs on their standard tracks.
Most chisels are beveled on the 2 sides and on the cutting edge, but specialty chisels may only be beveled at the cutting edge. This bevel will be at 20 to 25 degrees down the length of the blade on one side, and flat on the backside. The blade will be between 4” and 7” long. Make sure you get chisels with a grip that fits your hand. If the grip is too small, you won’t be able to hold the chisel steady as you work. Be sure to use a mallet or wood hammer when you work, so that you don’t destroy the head on your chisel. Keep track of the edge caps, keep them sharp, and oil the metal now and then after you’ve used them, and they should be good for years. If you don’t have the edge caps, get a roll to keep them in. This will prevent them from bouncing around in your tool box drawers and getting damaged.
I’ve got two sets sitting under heavy books right now drying overnight. Thank you so much for this! I bought the 8 planks of wood like you said but when I put them together it was uneven so I used 3 wide and 2 small for a perfect 2ft square table. Because of the extra I have enough for another set! I’m so excited I’m just starting to get into food photography so I found your blog just in time . Thanks!!
Thermal imaging systems work great at finding water leaks, electrical hot spots, and insulation gaps in walls. But until recently, thermal imaging systems were not a practical tool for the average contractor because they cost thousands of dollars and were the size of a microwave oven. But now this extremely helpful technology is accessible. FLIR’s new C2 compact imager is pocket-size but has most of the same important features as larger models. The touch screen controls are intuitive to use, and it acts as a regular camera as well, which helps when pointing out to homeowners or coworkers where exactly the trouble spots are. They also make models that work with your smartphone.
Diablo's 3 piece Adjustable Cabinet Router Bit Set Diablo's 3 piece Adjustable Cabinet Router Bit Set features a rail and stile bit set and a Double Shear raised panel bit. Featuring TiCo carbide with titanium these bits provide a long cutting life and ultra-fine finish. Perma-Shield Diablo's high performance coating reduces friction and build-up on the bits. The ...  More + Product Details Close
×