The Stanley 32050 FatMax Power Claw is a clever power strip built into a clamp. It can grab on to a stud, rafter, sawhorse or ladder. Hang it wherever you need power. This strip works great at keeping extension cord connections off the ground. That’s convenient, but it makes even more sense if you’re working outside on a wet surface. The Power Claw has three grounded outlets and a 15-amp breaker.
Whether you're new to woodworking or you've been doing it for years, Woodcraft's selection of woodworking projects is one the best places to find your next big project. Whether you're looking to make wooden furniture, pens, toys, jewelry boxes, or any other project in between, the avid woodworker is sure to find his or her next masterpiece here. Find hundreds of detailed woodworking plans with highly accurate illustrations, instructions, and dimensions. Be sure to check out our Make Something blog to learn expert insights and inspiration for your next woodworking project.

PROCESSING NOTES: No matter how easy I have tried to make following these media center plans and constructing them, if you find it overwhelming to attempt the project or operate the basic tools necessary for completion, get help. Contact your local supplier to see if sheet goods can be ripped to fit your car trunk. The possibility of ordering all the parts ready for assembly is also available. Most importantly, when you set off to build your project, help is only an email message away. 

I've worn this apron in my studio/workshop several times now, and I really like it. It's more expensive than some, but the materials and construction are first-rate. I rarely give five stars, but the workmanship on this apron is impressive. The fabric is substantial and, although a bit stiff at present, comfortable to wear. The strap and grommet system is pretty clever, allowing a good fit for most, I would think. I'm a 5'-7" not-skinny woman, and I'm able to cross the straps at the small of my back and then tie them in front, so I'm guessing there would be plenty of strap length for bigger men. The straps sit comfortably on my shoulders. And all the pockets are great!
Just redid my dining room table with this technique and I an observation/suggestion others might find helpful. The boards did not line up well putting it together upside down, even on a flat concrete floor with me standing on the boards while they were screwed. I would have combined biscuits with the pocket holes to ensure a better alignment of the boards. Lots of sanding was required after assembly, and this might not be a huge deal with pine, but I used hard maple so it was quite a chore even with a belt sander. Also, be aware that the 1x2s around the edge may not line up perfectly -- I had to trim about an eighth inch from each side after assembly to get nice smooth, even edges. Not a big deal, but the top turned out a little smaller than the specifications I was give by SheWhoMustBeObeyed. Otherwise our table now looks great, and thank you for the post!
Using shelving in your room or kitchen is a great way to arrange and de-clutter space… I know, such ground-breaking term it is. Do not write me off yet, I just want to show you how you can build some clean floating corner shelving that appears to have no brackets. You can create them at no cost, and the hardest part of the plan is figuring out what you are going to put on these shelves when you are finished.
After your table is pieced together, you will flip it over {remember, you've been working on it upside down} and sand it.  My husband isn't a big fan of the planks and worried about cups and plates getting stuck and spilled on the uneven parts of the boards, so he went to town with the sander. You can keep more of the plank look by sanding it less.
The most commonly purchased claw hammer is the 20 oz. size. It’s heavy enough to easily drive nails but easily manipulated when pulling nails. While wooden handles are picturesque, they may not stand up to the strain if you have to pull a lot of nails. Hammers with a steel handle, or even fiberglass, will be stronger. However, these won’t absorb the vibrations from driving nails the way a hickory handle will. You’ll also need to make sure the fiberglass and metal handles have a rubberized grip for control and comfort. If you’re going to be driving a lot of nails, the wooden handled hammer will be better for reducing stress on your hand, and wrist, too.
A super simple iPad Dock/stand made out of a single block of wood features an angled groove which gets to support the tablet device and a cut in a hole to revise access to the home button of your iPad. It’s possible to drill an access channel in the stand through which you can run a charging cable, although this mini stripped back iPad stand may have very limited functions.
Hanging upper cabinets is a tough task for one person. Having a lifting buddy to help is usually a good idea but costs extra. Little Hands HD is perfect for the guy who mostly works alone. The 6 x 6-in. base keeps the cabinets stable, and each lift can handle 150 lbs. The lever action can be raised a tiny fraction of an inch at a time, but sneak up on your target height because lowering the lifts isn’t quite as easy.
Some tools that are required for this project are Miter saw, drilling machine, pencil, tape measure, screws, etc. Those, who prefer a video tutorial instead, can visit the below link to a YouTube video tutorial that illustrates the process of creating a DIY Beer Bottle Crate. The video tutorial explains every step properly so that anyone can make a Beer bottle crate easily.
After your table is pieced together, you will flip it over {remember, you've been working on it upside down} and sand it.  My husband isn't a big fan of the planks and worried about cups and plates getting stuck and spilled on the uneven parts of the boards, so he went to town with the sander. You can keep more of the plank look by sanding it less.
This plan is probably the easiest plan ever added in the list. The one who is working on this project, don’t need any professional skills but just knowing some basics of woodworking will be enough for this DIY. You will get step by step detailed process of this tutorial in the source linked tutorial. This tutorial will surely help you to build this plan quickly.
From the source tutorial, you can get illustrates to the instruction about the plan. Everything is fairly described as diagrams, images, the list of supplies and tools need etc. The process to this plan is very easy to understand and follow for if you are having some basic woodworking knowledge. Make sure to collect all the supplies you need before you start with the project. You may even ask any question directly in the comment section of the tutorial post and also comment the images of your final product if you have completed it. Either way, I hope that you will manage to build this one nicely.​
But when you get a much larger tabletop (especially ones with small aprons or no plywood underneath)- you've got more opportunity for movement. A small cupping across each board can become substantial across an entire tabletop. Consider attaching your tabletop with tabletop fastners. You just make a small cut in the aprons with a circular saw, insert the tabletop fastner (also called Z-Clip) in the cut, and attach other end to the underside of the tabletop.
And if you haven’t got a fancy stencil hanging around, you can still give your table a stencil-styled makeover, and it won’t take much.  To make this fun herringbone table, Shark Tails took a boring side table and taped off a herringbone design then spray painted it gold!  It adds a touch of mod glam that’s not overwhelming since it’s in a small dose. // Shark Tails
If you have already graduated from college or university and are searching for a good job, you need to have a persuasive resume to impress your future employer. Our team of writers who provide this type of assistance will be glad to make a job-winning resume for you. If you need a cover letter, we can help with it too. Tell our expert about your experience, skills, and goals, and become a step closer to the job of your dream.
This could quite possibly be the best tool on this list! Have you ever tried to get your drill in a tight spot where you absolutely had to use it and just couldn’t? Holy Moly has this happened to me like 100 times. Almost nothing is more frustrating! With this flex shaft, you can bend around corners and fit into impossibly tight spaces like a knife through hot butter! Buy this thing!!!!
PROCESSING NOTES: No matter how easy I have tried to make following these media center plans and constructing them, if you find it overwhelming to attempt the project or operate the basic tools necessary for completion, get help. Contact your local supplier to see if sheet goods can be ripped to fit your car trunk. The possibility of ordering all the parts ready for assembly is also available. Most importantly, when you set off to build your project, help is only an email message away.
Consider building your tabletop out of boards about 6" wide (1x6 or 2x6), or close in size (I use x4 and x8 boards on occasion). If you go smaller, you'll be adding more joints, which means more pocket holes and more sanding. If you go with a wider board, the board itself may cup over time, creating high and low points on your tabletop. I personally find x6 boards to be that happy medium.
×