There was a big crowd, rocking music, and a lot of excitement over the Extreme Post-it Notes at the 3M booth at the 2018 International Builders Show. Apparently these things stick to wood, hot stuff, cold stuff, wet stuff, brick, metal, plastic pipes, ladders, stair treads, flooring, the side of a truck, copper, tools, siding, co-workers, concrete, tile, drywall, asphalt, house wrap, light fixtures, switches, cabinets, leather belts, windows…well, you get the idea. Post-it Extreme Notes will be available at major retailers beginning in March 2018.
Set biscuit joiner depth to #20. Lay the four best planks out on a flat surface and arrange them in final position. With a pencil and working across two boards at a time, make a mark at every 8-inch point along the seam of two boards. After marks are made, use the joiner to cut the biscuit slots at each location. Align the reference mark on the tool (similar to circular saw) and hold the top plate firmly flat against the board. In one smooth motion, plunge the tool until it hits the stop. Note: Do not cut joints on outside edges of first and last board.
There was a big crowd, rocking music, and a lot of excitement over the Extreme Post-it Notes at the 3M booth at the 2018 International Builders Show. Apparently these things stick to wood, hot stuff, cold stuff, wet stuff, brick, metal, plastic pipes, ladders, stair treads, flooring, the side of a truck, copper, tools, siding, co-workers, concrete, tile, drywall, asphalt, house wrap, light fixtures, switches, cabinets, leather belts, windows…well, you get the idea. Post-it Extreme Notes will be available at major retailers beginning in March 2018.
Hey Cara – We bought MinWax wooden stain in Cherry (the teeny, tiny can) and one other color, but it has been misplaced in the garage somewhere. We picked up sample sized containers of paint in Satin finish (we bought them at Lowe’s so it was Olympic brand). I just found pretty blue and dark red paint chips and the paint counter guy did the rest! Hope that helps – happy to answer questions if you need any more info
The Wilton ATV All-Terrain Vise is a tool for those of you who work out of your pickup at job sites and need a serious on-site vise. And this vise is worth the price! It slips into any 2-in. receiver hitch and has a sizable flat anvil area for pounding. It comes with a bracket for attaching to any sturdy surface, such as a trailer, if you don’t want to use your truck.
By posting on this site and forum, the poster grants to Canadian Woodworking Magazine/Website the unrestricted rights to use of the content of the post for any purpose, including, but not limited to, publishing the posted material, including images, in print or electronic form in a future issue or issues of Canadian Woodworking magazine or related Canadian Woodworking products, and to use the post for promotional purposes without further compensation, as well as the right to use the poster's name in a credit along with the post.
For all of your wood cabinetry and joinery tools and supplies, Infinity Cutting Tools has got you covered. We offer joinery tools and accessories for making box joints, finger joints, pocket holes, dowel joinery, dovetails, and mortise-and-tenon joinery. When it comes to installing cabinet hardware like knobs, pulls, and hinges, check out our cabinet hardware installation solutions.

This super-strong and simple-to-build workbench is may be the project you've been looking for a long time. You have to select some free workbench plans to create yourself a working table in your shed that after you can use it when you are working on your projects and maybe it can provide you some extra storage, depends upon which plan you are choosing to DIY.
No, it’s not a blood pressure tester. It’s an inflatable shim sold by Calculated industries. What in the world would you do with an Air Shim? Well, you could hold a window in position (by yourself) while setting the permanent shims, or prop up a door slab during installation without scratching the hardwood floor. Use it to align base cabinets or level appliances. You could even trick your big, burly buddy by betting him that your 10-year-old can pick him up off the ground… you will win that bet because the Air Shim is easy enough for anyone to pump and it holds up to 300-lbs. Deflate it as slow as you want for uber precision adjustments.
And if you haven’t got a fancy stencil hanging around, you can still give your table a stencil-styled makeover, and it won’t take much.  To make this fun herringbone table, Shark Tails took a boring side table and taped off a herringbone design then spray painted it gold!  It adds a touch of mod glam that’s not overwhelming since it’s in a small dose. // Shark Tails
Here’s a traditional Swedish farm accessory for gunk-laden soles. The dimensions are not critical, but be sure the edges of the slats are fairly sharp?they’re what makes the boot scraper work. Cut slats to length, then cut triangular openings on the side of a pair of 2x2s. A radial arm saw works well for this, but a table saw or band saw will also make the cut. Trim the 2x2s to length, predrill, and use galvanized screws to attach the slats from underneath. If you prefer a boot cleaner that has brushes, check out this clever project.

When you buy the wood, look for pieces that aren’t warped, excessively longer or shorter than the others, and, if you can get lucky, don’t carry the telltale “new wood” planer marks. We purchased the most inexpensive wood that we could find. You’ll likely find them in 2- and 4-ft pieces. If you have a saw at home, you might consider getting the 4 ft pieces to decrease the cost of your project a bit.


Hey Cara – We bought MinWax wooden stain in Cherry (the teeny, tiny can) and one other color, but it has been misplaced in the garage somewhere. We picked up sample sized containers of paint in Satin finish (we bought them at Lowe’s so it was Olympic brand). I just found pretty blue and dark red paint chips and the paint counter guy did the rest! Hope that helps – happy to answer questions if you need any more info
Aside from the privacy it offers, a latticework porch trellis is a perfect way to add major curb appeal to your home for $100 or less. The trellis shown here is made of cedar, but any decay-resistant wood like redwood, cypress or treated pine would also be a good option. Constructed with lap joints for a flat surface and an oval cutout for elegance, it’s a far upgrade from traditional premade garden lattice. As long as you have experience working a router, this project’s complexity lies mostly in the time it takes to cut and assemble. Get the instructions complete with detailed illustrations here.
And if you haven’t got a fancy stencil hanging around, you can still give your table a stencil-styled makeover, and it won’t take much.  To make this fun herringbone table, Shark Tails took a boring side table and taped off a herringbone design then spray painted it gold!  It adds a touch of mod glam that’s not overwhelming since it’s in a small dose. // Shark Tails
I used a dry brush, barely dipped it in paint, and then lightly brushed it over the wood. If you get too much coverage with the paint, sandpaper is your best friend! You can stain the wood if you want a darker look peeking out from underneath. Check out the stain in this DIY post, it’s a great way to get that aged look quickly: http://www.jasonandshawnda.com/foodiebride/archives/11310
Look at the amazing masterpiece Domestic Imperfection made out of her plain Jane dining table!  Using a stencil and white paint, you can create this design or similar, then tone it down and make it look slightly aged by staining the wood right over the top of the painted design!  Very clever stenciled and stained table redo. // Domestic Imperfection
These tweezers are perfect. They’re nice and small and infinitely better than the cheap ones sold out of fishbowls at the home-center checkout lane. Their sharp, sturdy precision tips can grab even the tiniest sliver. Put them on your key chain and you’ll have a really high-quality stainless steel tweezers ready for the next time you have to perform a little surgery on the battlefield. They fold up like a pocketknife, so the business end doesn’t get wrecked. They’re available only at pocketweez.com.
When you buy the wood, look for pieces that aren’t warped, excessively longer or shorter than the others, and, if you can get lucky, don’t carry the telltale “new wood” planer marks. We purchased the most inexpensive wood that we could find. You’ll likely find them in 2- and 4-ft pieces. If you have a saw at home, you might consider getting the 4 ft pieces to decrease the cost of your project a bit.
With a pencil and a protractor, divide the larger disc into 30-degree wedges to create 12 center lines for the bottle indents. Center and trace the smaller disc on top of the larger disc. Next, with a drill press, drill 3/8-in.-deep holes on the 12 center lines with the 1-7/8-in. Forstner bit, spacing them between the disc’s outer edge and the traced circle. Next, divide the smaller disc into 60-degree wedges and drill six more 3/8-in.-deep holes with the Forstner bit. 

Woodworking power tools include various saws for cutting the wood to size and drills for creating holes. Sand pieces down to the finish you want before you sand with portable sanders. Use drivers to install woodworking fasteners for a durable final piece. Cleverly designed rotary tools feature removable bits that can drill, drive, sand, cut and more, so you can use a single tool to accomplish virtually every task of your project. For a production-level project, nail guns can save you hours or even days depending on the work involved.
I’ve been toying with the idea of building a new table top. The legs of my dining table are hardwood. But the table top is not; it’s covered in veneer which is coming off in strips. I thought of removing the table top completely and utilizing the existing legs with a newly built hardwood top. But you’re solution seems easier! However, my tabletop is much thicker than yours, a 1 x 1 inch lip would not suffice. Can I just adjust the size of the lip, 1 x 2 inch? Or do I have to adjust the size of all boards used? Thanks!
Your monster of a table is going to be HEAVY, so I strongly recommend moving it to its final destination in two pieces–lay a blanket down in your dining room, put the top on it upside down, then the frame upside down on top of that. Attach a couple 2×4 supports across the frame for good measure, then begin the frustrating process of centering the frame on the top. Once you have the top centered, attach your brackets–I did two on each end and three on each side.
There are lots of clear finishes. But for a combination of usability and durability, you can’t beat polyurethane. Oil-based poly, which dries slower than water-based, is best for beginners because it allows more working time. The other important difference is clarity: Water-based poly is absolutely colorless, while oil-based has an amber tone, which can be good or bad depending on the look you want.
×