This is a unique and cherished tool in my shop. 30 years ago my brother was a nuclear pipe welder at a federal submarine yard. He made this there and came home with it one day. The blade is submarine hull steel, Nickel Cobalt. I’ve never been able to sharpen it and it’s never really gotten dull. I had a diamond stone but quickly stopped using it as the diamond dust was being stripped off the stone. It has nostalgic and useful meaning to me.

Let’s start with perhaps the most basic tool in every household – the claw hammer. The claw on one side of the head should be well counterbalanced by the finished head, which should be somewhat rounded. The other kind of head is the waffle-head. Most commonly used in construction, it leaves a distinctive waffle mark on the wood when you drive the nail. This, of course, is not the proper nail for woodworking.

Crisp, tight joints are key to any great tabletop, and this is where the jointer comes in. Get help supporting boards longer than about five feet as you work. Also, if some joints don’t come together tightly, despite your best jointing efforts, try moving the boards to new locations if grain patterns permit. Some edges just naturally fit together more tightly than others. Don’t own a jointer? Pieces of planed lumber sometimes fit together just fine without jointing. Try different boards as neighbours to see which ones get along the best.
Cut off a 21-in.-long board for the shelves, rip it in the middle to make two shelves, and cut 45-degree bevels on the two long front edges with a router or table saw. Bevel the ends of the other board, cut dadoes, which are grooves cut into the wood with a router or a table saw with a dado blade, cross- wise (cut a dado on scrap and test-fit the shelves first!) and cut it into four narrower boards, two at 1-3/8 in. wide and two at 4 in.
Just a little nitpick on the tape measure blurb. The hook should not be completely tight. It should move in and out about a 1/16th or the thickness of the hook. This way you get an accurate measurement whether you hook a part to measure or bump up to it. If you want more accurate measurements with a tape measure, “burn” an inch instead of hooking or bumping the part. Just line up what you want to measure with the 1″ mark and subtract that inch from the final measurement.
The Bosch Max FlexiClick 5-in-1 Drill/Driver System has one tool and five attachments. That means it can perform all kinds of tasks, like: screw-driving, drilling, right angle drilling/driving and offset driving close to edges. This tool/tools isn’t going to replace a deck builder’s 20v impact driver and drill, but it might be a great option for those smaller project that require a bunch of different operations, like knocking off a punch list at the end of a build-out. If you’re moving around and don’t have the space to haul around a bunch of dedicated tools this might be just what you’re looking for. The Bosch 5-in-1 Drill Driver System is available online and in home centers for $199.00.
No, it’s not a blood pressure tester. It’s an inflatable shim sold by Calculated industries. What in the world would you do with an Air Shim? Well, you could hold a window in position (by yourself) while setting the permanent shims, or prop up a door slab during installation without scratching the hardwood floor. Use it to align base cabinets or level appliances. You could even trick your big, burly buddy by betting him that your 10-year-old can pick him up off the ground… you will win that bet because the Air Shim is easy enough for anyone to pump and it holds up to 300-lbs. Deflate it as slow as you want for uber precision adjustments.
Here’s a traditional Swedish farm accessory for gunk-laden soles. The dimensions are not critical, but be sure the edges of the slats are fairly sharp?they’re what makes the boot scraper work. Cut slats to length, then cut triangular openings on the side of a pair of 2x2s. A radial arm saw works well for this, but a table saw or band saw will also make the cut. Trim the 2x2s to length, predrill, and use galvanized screws to attach the slats from underneath. If you prefer a boot cleaner that has brushes, check out this clever project.
No, it’s not a blood pressure tester. It’s an inflatable shim sold by Calculated industries. What in the world would you do with an Air Shim? Well, you could hold a window in position (by yourself) while setting the permanent shims, or prop up a door slab during installation without scratching the hardwood floor. Use it to align base cabinets or level appliances. You could even trick your big, burly buddy by betting him that your 10-year-old can pick him up off the ground… you will win that bet because the Air Shim is easy enough for anyone to pump and it holds up to 300-lbs. Deflate it as slow as you want for uber precision adjustments. 

The owners, webmasters, administrators, authors and editors, expressly disclaim all and any liability to any person, whether a user of this website or not, in respect of anything and of the consequences of anything done or omitted to be done by any such person in reliance, whether whole or partial, upon the whole or any part of the contents of this website. Please exercise caution when working with any tools or machinery. Follow common safety rules and precautions as outlined in any manuals related to the equipment being used. If advice or other expert assistance is required, the services of a competent professional person should be sought.
This DIY has a bit of a backstory: In my basement workshop—as a byproduct of about a half dozen previous projects—I’d managed to accumulate a small mountain of scrap wood. Though the pieces varied in size, most were 2×4 boards. For weeks, I pondered the question of how to use them. There wasn’t enough material to build anything substantial, but at the same time, this was much more wood than I would feel comfortable chucking or committing to kindling. I suddenly seized on the idea of turning those leftover boards into a rustic tabletop, but then I let the project momentum slow to a creep, and in the blink of an eye another few weeks had gone zooming by. Things finally came to a head one day when I was scanning the local giveaway listings. There, I discovered that one of my neighbors was trying to get rid of an old metal garden table. Upon seeing the pictures, I knew immediately that this would be a great table to top with the scrap wood surface I’d been planning to make with all those 2x4s!
What makes this JCB Teleskid machine unique is it’s one-of-a-kind telescoping boom, which gives it the ability to reach a variety of places. The Teleskid’s telescoping boom gives you eight feet of outward reach. Plus, its one armed design gives you 60 percent more visibility than similar twin-armed machines. With a fully extended boom the Teleskid can lift up to 1600 pounds. With the boom retracted that weight capacity goes up to an impressive 3695 pounds. To find out more about the Teleskid from JCB, click here.
I've used these to turn a dozen bowls so from everything to Paduk, zebrawood, cherry, olive wood, etc. and They require sharpening maybe once a bowl. They are easy enough to hand sharpen using a work sharp, and generally last me throughout the entire bowl. The only gouge I have used that is much nicer is the Easy Wood Tools replaceable tip gouges that are super sharp and make quick work of any bowl. Those cost as much per gouge as this entire set...so this is definitely a good beginner set to start your turning arsenal. I plan to supplement a few Easy Wood scrapers into my set.
The engineering involved in building this garden bench is pretty simple, and we have provided some links to get a full cut list and plans with photos to help you along the way. Additionally, to the stock lumber, you will need wood screws, barrel locks, and hinges to complete the table. A miter saw or hand saw is also extremely helpful for cutting down your stock to the correct angle and length.
One of the best stud finders you’ll ever use is the Franklin Sensors ProSensor 710. It’s unique in that there’s a whole bar of red lights that light up whenever it detects a stud. Unlike other sensors, which have a single light that stays on as it passes over the wood, the lights on the 710 tell you exactly where the wood stops and starts. No guesswork. Push a button, drag it over the wall and those hidden mysteries reveal themselves. You won’t even need to read the directions!
”Before matches became widely available in the 1860s, long, coiled wood shavings known as spills were used to transfer a flame from one location to another, such as from a fireplace to a candle, lantern or stove. Typically made using a special inverted plane, spills burn more slowly and consistently than paper, and also double as a convenient tinder material. We based the design of our spill plane on an 1850s Edward Preston spill plane in our collection.”

A trusty pair of Electrician Scissors is the most used tool of many of the low-voltage electricians that we’ve talked to, and Klein seems to be the go-to brand. If you’ve never heard of electrician scissors, here is a primer: Of course like any scissors, Klein’s new Electrician Scissors can cut through stuff with the blades, but they also have a cable cutting notch so you can rip through wire up to 14 AWG. They’ll strip 19 and 23 AWG wire all day long and have a notch in the tip for de-burring electrical boxes. There’s also a scraper on both blades for convenient wire cleaning. Klein’s All-Purpose Electrician’s Scissors are available online and in home centers for $24.35.
With a collection of workshop tools--whether for construction jobs or for around the DIY house projects--it’s top priority to make sure all of your tools are in the best shape and are taken care of. Tools don’t come at a cheap price, so proper care is essential in order for them to last for a long time. Unfortunately, after much usage, wear, tear, and rusting of tools tend to happen. Luckily, at Bora Tools, we sell a vast variety of workshop accessories that are specific to cleaning and restoring needs. From waxes, polishes, rust removers, to covers, racks, and more, we have an abundance of products that are designed to keep your high-quality, expensive tools in prime condition all year round. 

Making a garden arched footbridge out of some wood boards can be fun, hard working plan and also it’s quite rewarding. We are providing the project tutorial for how to build an arched footbridge without rails or having rails. If you take your hands of work and have some basic woodworking skills you can easily build this type of bridge. While this garden bridge is too small to walk over but it can make a really stunning addition to your lush yard or garden.

There’s a lot of space above the shelf in most closets. Even though it’s a little hard to reach, it’s a great place to store seldom-used items. Make use of this wasted space by adding a second shelf above the existing one. Buy enough closet shelving material to match the length of the existing shelf plus enough for two end supports and middle supports over each bracket. Twelve-inch-wide shelving is available in various lengths and finishes at home centers and lumberyards.


If you have been with me for a while then you know that I participate in a monthly Furniture Fixer Uppers share. That is where a few of my creative and talented blogger friends and I have joined together to share what we are working on. This is a new group of Furniture Flipping friends and we will be sharing on the 1st Thursday of each month to bring you even more great furniture makeovers. DIY projects and furniture makeovers are more fun with friends anyway, so the more the merrier, right? Let’s see what my friends are up to! Make sure to click the links below the image to check out all the amazing projects that my bloggy girls are working on this month.
The deep grain lines in woods like oak or walnut will telegraph through the clear finish, no matter how many coats you apply. And that’s fine; it’s part of the character of coarse-grain woods. But if a perfectly smooth surface is the look you want, use a grain filler. You’ll find several products online or at woodworking stores. With most, you wipe on the filler, squeegee off the excess with a plastic putty knife and then sand after it’s dry for a smooth-as-glass surface.
Woodworkers are a social bunch, and there are a few popular forums where people share thoughts on tools, discuss technique at length, and—of course—upload their plans. Some of the most active online woodworking communities include Lumberjocks, Woodworking Talk, Wood Magazine, WoodNet, Kreg, and Sawmill Creek. Search those to see if they have what you’re looking for (either with their built-in search tool or with Google’s site-specific search, e.g. site:lumberjocks.com side table).
Do you enjoy splinters or cuts from metal flashing? Nope me neither. THESE GLOVES ARE THE SHIZ NIT! I have yet to get a splinter when handling my rough-edged plywood. Not only are they cheap but extra reliable. Mom these gloves are for you (My poor mom always gets splinters when she helps me DIY). This is one of the unique tools you’ll be happy you own.
Reclaimed Wood from Corn Crib HOW TO DESIGN AND BUILD AN ENTRY WAY COAT RACK AND BENCH There was a door in granddad’s home the client wanted to preserve and wondered, if they provided the wood, could I build an entryway coat rack and bench using the door as part of the build. The wood they wanted to provide, well, that was from the family owned Tennessee corn crib that had been torn down and they didn’t want to lose the wood or the memories. Not only was this a corncrib but it was eventually used by the great grandchildren as a play house. So for the client there are as many memories in this build as there are colors. THIS PROJECT TRULY DEFINES THE “CUSTOM” in BAYNE CUSTOM WOODWORKING. I spent some time to design a simple layout in @sketchup_official so the client could approve the idea I had in mind. The wood showed up in two deliveries so we stacked it outside because this was the first time I worked with barn wood. I did not want to introduce possible termites to my shop. So my first call was to my pest guy asking how I would treat the wood for termites. Much to my relief he said I had nothing to worry about. This was “real” wood! Not nominal at all, nominal is how we buy our wood at a local hardware store. Where a 2×4 is actually 1 ½  x 3 ½ . These 2×4’s were at least 2”x4”’s if not more and were hard, heavy and dusty, did I say heavy? After cutting to length on my handy @DewaltTough miter saw, I had to take them to my @ridgidpowertools table saw and square up the bottoms only.  I was very careful not to lose any of the original saw marks and character because that would ruin the entire purpose. For someone who likes clean, crisp edges, this was a bit of a challenge. I used @kregjig Kreg Jig® K4 Master System to join all the pieces of the base, the seat frame and the supports to join the two together. I was very careful to hide all of the pocket holes so they could not be seen from any angle. I used Titebond Products original interior wood glue to join all the pieces together. The next item was to assemble the back which included grandad’s door as the center piece. The door was only 71 ½ tall which determined the overall height of the project. Part of this back also includes two live edge pieces that we picked to use as the “L” shaped wings or side walls. The door measured 24” which left me with 6” on each side to make up the final size of 36”. So I chose two of the straightest boards that were closest to 6” and cut them to width so as not to waste any wood or lose any character. I used the Kreg Jig® K4 Master System
You can also use Google image search to research a project. Unlike the PDF search, the image search provides a photo of what the project will look like, which is helpful in determining if you want to pursue building it. By doing an image search for how to build a step stool, you will have a ton of options that all lead to woodworking plans of various quality. (The how to part of these is important—otherwise you’ll just get pictures of step stools.)

The deep grain lines in woods like oak or walnut will telegraph through the clear finish, no matter how many coats you apply. And that’s fine; it’s part of the character of coarse-grain woods. But if a perfectly smooth surface is the look you want, use a grain filler. You’ll find several products online or at woodworking stores. With most, you wipe on the filler, squeegee off the excess with a plastic putty knife and then sand after it’s dry for a smooth-as-glass surface.
Verdict : Ted’s product is EXTREMELY extensive with 16k plans and there are tons of projects to choose from. Not every woodworker online loves it, but it’s cheap and perfect for every level of experience, I love it because this is basically the only resource I need. I highly suggest it. They also offer a really solid money back guarantee if you don’t like it after all.
Keep your woodworking tools and knives razor-sharp with our wide variety of sharpening supplies and accessories. We have what you need for jointer and planer knife sharpening. For sharpening plane irons and chisels, we supply a variety of diamond and waterstones, the Infinity Sandpaper Sharpening System, and honing guides. Our power sharpening systems include the Worksharp Knife Sharpeners, Ken Onion edition for the sharpest knives in the drawer.
Pallet tables are very common and very easy to make. To make it you’ll need about half of a wood pallet. Decide the dimensions for the table and then remove some of the boards and cut them to size. Reattach them using nails and then sand the table. Then you can stain or seal the wood if you want. At the end, you can either add legs, casters or leave the table as such.{found on hernewleaf}.
This Privacy Policy covers CanadianWoodworking.com's treatment of personally identifiable information that CanadianWoodworking.com collects when you are on the CanadianWoodworking.com site, and when you use CanadianWoodworking.com's services. This policy also covers CanadianWoodworking.com's treatment of any personally identifiable information that CanadianWoodworking.com's business partners share with CanadianWoodworking.com.
Be sure wood is dry. Material from a job site or floor joists that existed in a crawlspace may have high moisture content; material from a conditioned space should be dry. Wood can be dried in a kiln (ask your local lumber mill) or stored inside through the winter. If time does not permit, stack wood in a hot dry place with 1" spacers between layers. Allow to dry for a minimum of two weeks.
”Before matches became widely available in the 1860s, long, coiled wood shavings known as spills were used to transfer a flame from one location to another, such as from a fireplace to a candle, lantern or stove. Typically made using a special inverted plane, spills burn more slowly and consistently than paper, and also double as a convenient tinder material. We based the design of our spill plane on an 1850s Edward Preston spill plane in our collection.”
For starters, this DIY wood table is for my son to keep his Lego projects and erector set buildings on. Secretly, it’s for me because, in turn, it will keep the Legos from being scattered all over my house. We decided on measurements of 60″ long x 18″ deep for the table top. Now that I know how big I want our homemade table to be I reached out to Osborne Wood Products to find out what the next step is for building a table. They were super helpful and made it very easy to order the table base kit. We let them know the measurements for the table top as well as how much of an overhang. We then choose the traditional dining table legs in soft maple along with a 4″ wood skirt also in soft maple. The furniture kit came well packaged and rather quickly. 
There is no cost to use the database. Registering is not required. You should be able to browse the database and click through the links. Having said that, considering the fact there are so many browsers out there being used, this site's software might not allow some visitors to browse, it all depends on the Internet traffic, and your browser's compatibility.

There was a big crowd, rocking music, and a lot of excitement over the Extreme Post-it Notes at the 3M booth at the 2018 International Builders Show. Apparently these things stick to wood, hot stuff, cold stuff, wet stuff, brick, metal, plastic pipes, ladders, stair treads, flooring, the side of a truck, copper, tools, siding, co-workers, concrete, tile, drywall, asphalt, house wrap, light fixtures, switches, cabinets, leather belts, windows…well, you get the idea. Post-it Extreme Notes will be available at major retailers beginning in March 2018.

This plan is probably the easiest plan ever added in the list. The one who is working on this project, don’t need any professional skills but just knowing some basics of woodworking will be enough for this DIY. You will get step by step detailed process of this tutorial in the source linked tutorial. This tutorial will surely help you to build this plan quickly.


Adirondack Chairs in Tennessee Cedar Wood Growing up in Central New York and spending years in the Adirondack Mountains, I grew up seeing all types of Adirondack chairs. But it was not until I moved to middle Tennessee that I attempted to build Adirondack chairs myself. I found plans that gave me the basic design to build the adult chairs. I made some adjustments in order to fit them into my style and the type of wood that I have available. I found a cedar mill within an hour of my shop that allows me to purchase rough cut lumber. Because of the nature of rough lumber I am buying wood that is actually thicker, wider and longer than wood purchased at a brick front store.  Where a nominal 2”x 4”x 96” bought at a local lumber store is actually 1.5 x 3.5 x 96. The cedar I purchase is 2 ¼ x 4 ¼ x 102 inches. Once run through the surface planer to clean up the roughness and sanded, I am able to build with actual 2” x 4” or 2” x 6” lumber. This makes the chairs heavier, sturdier and more durable. Because of the size of the wood I assemble the legs and main supports with 3/8” carriage bolts. The arms, seat boards and backs are all assembled with 2” to 3” exterior screws. I predrill all the holes prior to inserting any screws. I do this because cedar, or any wood for that matter, can split at any time. The actual finished chair stands 38” tall x 39” long and 33” wide. They weigh about 35 lbs. and can seat a large adult very well but also comfortable for my tiny framed wife. The rise of the seat from the knees to the ground for your feet is 13 ½ inches. The seat reclines backward naturally but not so much that it is hard to stand from a seated position. The back is curved to support the natural curve of your back allowing for a more comfortable fit. The back is 32” tall to support even a taller person. The arms have been described as looking like whales so they are narrow where they fasten to the back of the chair and wide in the front for a cup, a book or even a laptop if you choose to work outside. *DISCLOSURE: Some of the links below are affiliate links. If you chose to click through and make a purchase I will earn a commission but there is no additional cost to you. It helps compensates the business for the time spent creating these posts. THANK YOU! Child’s Chair: The smaller child chairs are added to match the adult chairs to finish the family. These also are made with rough cedar milled and sanded to size to make the chairs sturdy. As with the adult chairs the wood will be thicker, wider and stronger than nominal wood. I use all true 1” lumber for the

Here’s an old woodworking adage I enjoy ignoring: “measure twice, cut once.” Honestly, I measure nonce and cut thrice. I often eyeball it. I use pieces I’ve already cut to measure what I need to cut. It’s not a great habit, but I prefer it to measuring everything. And the results usually aren’t that different. At least that’s what I tell myself. I ended up having to sand down the ends of the 2×12’s running the length of the table (where they meet the aprons) because they weren’t exactly the same length.
 THANKS ERIC! A few weeks ago we met Eric and Vicki Rhoten at the Work Bench Conference in Atlanta. We hit it off immediately, as we both have a passion for woodworking. As we were discussing our businesses, Eric mentioned how difficult it is for him to get certain woods in Arizona. We are blessed here in Tennessee to have many mills including a local cedar mill. I offered to send Eric some samples to try and that’s what this video is about. Eric does an awesome job demonstrating how he turned one of the pieces into a beautiful piece. We loved seeing the wood we sent turned into this awesome piece of art. Great job Eric! Need some wood? If you’re interested in getting your own pieces of cedar, we’ve put together some basic options and pricing. Since wood can be pretty heavy the mailing costs can be high, so we’ve found the sweet spot is three pieces of wood in a flat rate USPS box, to get the most wood for the price of mailing it! We’ll have a shopping area up very soon, but meanwhile use this form to contact me.  
Clamp curved caul edges inwards so they align tabletop boards in the middle, then torque up the main clamps to draw the boards together. If the width of boards you’re using allow it, pre-glue boards for your tabletop in sections that are just narrow enough to fit within your thickness planer. Run these through the planer to clean and level the glue joints, then move back to clamps for final glue up. Working in stages like this reduces the number of glue joints you need to sand smooth and level later.
Im am so glad you posted this! I bought a cheap dining room table from good will to use for my desk, it has a leaf in the middle to make it longer. I wanted to glue the leaf to the other two sides and thin fill in the holes with wood filler and I was advised by mom friend that it wouldnt work, but now I have proof cant wait to try it out!!! thanks 🙂

Are you redecorating your home but can’t seem to find the right table to complete your décor? Don’t worry too much because there are plenty of alternatives. There’s always a DIY project that can help you out. For example, we just found these beautiful DIY tables and we’re sure there are plenty more where these came from. Let’s take a look at them and see them closely.

When you buy the wood, look for pieces that aren’t warped, excessively longer or shorter than the others, and, if you can get lucky, don’t carry the telltale “new wood” planer marks. We purchased the most inexpensive wood that we could find. You’ll likely find them in 2- and 4-ft pieces. If you have a saw at home, you might consider getting the 4 ft pieces to decrease the cost of your project a bit.
This time I surprised one of my favorite dice games and took it outside. I made a set of wooden dice in just a few hours, and instead of sitting in the room and doing nothing, we are taking our dice game out into the yard. With this set of wooden dice, dice games are becoming our favorite backyard game. Check out the step by step tutorial below so you can make your own.
×