If you want your table top -- any table top -- to actually ast without bowing/cupping/twisting, you MUST attach it in a manner that allows for seasonal wood movement. Wood is an organic product, and it naturally expands and contracts with changes in temperature and humidity. I'll post link below to a couple of options that you can cheaply buy which will allow you to securely attach a tabletop while still giving the wood the flexibility to move with the seasons. When you buy decently-made furniture at a store, they all accommodate for this one way or another. Don't just screw the top down to the legs or the skirt...you'll regret it later on.
Everybody has a home remedy for sealing partially used tubes of caulk. But what if you had a single product that could seal caulk cartridges, squeeze tubes, glue bottles, felt-tip pens and anything else that has a nozzle? Well, these Little Red Nozzle Caps are just the ticket. Roll the cap down the nozzle to seal out dirt and preserve the remainder of the bottle, tube or cartridge.
The engineering involved in building this garden bench is pretty simple, and we have provided some links to get a full cut list and plans with photos to help you along the way. Additionally, to the stock lumber, you will need wood screws, barrel locks, and hinges to complete the table. A miter saw or hand saw is also extremely helpful for cutting down your stock to the correct angle and length.
The end grain of wood soaks up finishes and often turns much darker than the face grain. Check for this on your test block. If you get an ugly result, pretreat the end grain with a dose of finish that will limit absorption (wood conditioner, sanding sealer, shellac or polyurethane thinned 50 percent). Apply the treatment with an artist’s brush and be careful not to slop onto the face grain.
Touch ‘n Foam’s Gel Foam Subfloor Adhesive might make you want to chuck your caulking gun for good. It comes in a can and dispenses just like the spray-foam insulation everyone is familiar with. It lays down a bead way faster than tube adhesives but without the endless, wrist-busting trigger squeezing. And you’ll be able to keep working up to 10 times longer without stopping to reload. There’s no downtime due to wet or frozen lumber, and the can is reusable up to 15 days. To use Touch ‘n Foam Subfloor Adhesive, you’ll need an applicator gun (the same one used for expanding foam). There’s also a 46-in.-long barrel for the applicator gun that will save your back from a whole lot of bending over.
Work at a place where you’re required to wear a steel-toe boot? Then listen up. Wolverine just introduced a new boot that’s much more comfortable but still offers solid impact protection. Instead of steel, CarbonMAX boots have a protective cap made of carbon nanotubes, making them lighter and thinner. And if anyone knows about making comfortable work boots, it’s Wolverine—they’ve been making them for more than 130 years.
Behind every great woodworking piece is a great woodworking plan. Even the classic furniture makers of the 18th and 19th centuries worked from detailed precision drawn plans. This is how we are able to make such genuine looking reproductions of the works of the famous furniture makers of old; the master woodworker’s plans are still extant. Many different styles and designs are available, from all different periods in history, to modern designs from this century. Working with the right woodworking tools a skilled woodworker can make any piece of furniture; however fancy the detail is, if he has an accurate woodworking plan to work from. Once you have reached a certain skill level in your woodworking techniques, you will be able to create a masterpiece which can be handed down through your family for future generations.
Whether you're new to woodworking or you've been doing it for years, Woodcraft's selection of woodworking projects is one the best places to find your next big project. Whether you're looking to make wooden furniture, pens, toys, jewelry boxes, or any other project in between, the avid woodworker is sure to find his or her next masterpiece here. Find hundreds of detailed woodworking plans with highly accurate illustrations, instructions, and dimensions. Be sure to check out our Make Something blog to learn expert insights and inspiration for your next woodworking project.
Google is probably the first place where most people would start searching for woodworking plans, but often the top results can be a mix of articles and how-to pieces that just aren’t detailed enough. Sometimes they’ll link to the plans (like we try to here at Lifehacker), but other times, they’re just showing off a cool project. There are better, more precise ways of finding what you’re looking for.
You won’t believe what you can create with a bunch of free scraps. A stunning scrap wood table, by Instructables user Wholman for starters! This DIY is a bit time intensive, as the process for laminating wood can take many hours depending on the dimensions of your project, but the end result is nothing short of breathtaking. The natural wood grains, different colors and all the character from each piece of salvaged wood come together to make a show-stopping table. // Wholman on Instructables
A trusty pair of Electrician Scissors is the most used tool of many of the low-voltage electricians that we’ve talked to, and Klein seems to be the go-to brand. If you’ve never heard of electrician scissors, here is a primer: Of course like any scissors, Klein’s new Electrician Scissors can cut through stuff with the blades, but they also have a cable cutting notch so you can rip through wire up to 14 AWG. They’ll strip 19 and 23 AWG wire all day long and have a notch in the tip for de-burring electrical boxes. There’s also a scraper on both blades for convenient wire cleaning. Klein’s All-Purpose Electrician’s Scissors are available online and in home centers for $24.35.
Manufacturers that produce woodworking tools and materials have got into the content creation game, too, and some will share woodworking plans online. Minwax and Ryobi, for example, provides their plans free of charge, and Rockler offers their woodworking plans for a fee. Seek them out along with the other blogs and you’ll have a handy list of resources you can turn to for any project.
Online packages also allow you to build at a convenient pace, whether you want to build one bench per week or want to try every new furniture plan available – and more importantly, the use of clear instructions will enable you to build under a comfortable environment without any pressure. That way, you do not face disappointment that you would otherwise experience if you buy hard-to-understand furniture plans or can’t find the specific project that you’re looking for. If you think that a plan outline is simple, you can find a more difficult one and begin practicing new skills and techniques. That way, you are able to build more things faster than if you bought each plan individually and had to search for it each time.
As with most websites, we do log web visits. This information, however, does not have a link to you personally. These logs help us understand the needs of our audience and the areas of our site that you do or do not find useful. When you simply browse our site, no personal information is being collected. We may disclose this non-personal information to third parties such as sponsors, clients or advertisers.
One of the best stud finders you’ll ever use is the Franklin Sensors ProSensor 710. It’s unique in that there’s a whole bar of red lights that light up whenever it detects a stud. Unlike other sensors, which have a single light that stays on as it passes over the wood, the lights on the 710 tell you exactly where the wood stops and starts. No guesswork. Push a button, drag it over the wall and those hidden mysteries reveal themselves. You won’t even need to read the directions!