When it comes to choosing a finish there are two main choices. The typical approach of stain and urethane creates a smooth, wipeable surface, but when that finish eventually wears through, there’s no way of repairing it attractively. Sanding back to bare wood and refinishing is the only way to make it respectable again. Oil and wax finishes, on the other hand, take more time to apply initially, but they’re easily repaired and rejuvenated with the tabletop in place. Regular reapplication works just fine.
Most chisels are beveled on the 2 sides and on the cutting edge, but specialty chisels may only be beveled at the cutting edge. This bevel will be at 20 to 25 degrees down the length of the blade on one side, and flat on the backside. The blade will be between 4” and 7” long. Make sure you get chisels with a grip that fits your hand. If the grip is too small, you won’t be able to hold the chisel steady as you work. Be sure to use a mallet or wood hammer when you work, so that you don’t destroy the head on your chisel. Keep track of the edge caps, keep them sharp, and oil the metal now and then after you’ve used them, and they should be good for years. If you don’t have the edge caps, get a roll to keep them in. This will prevent them from bouncing around in your tool box drawers and getting damaged.
A layout square, or combination square, comes in 6” and 12” sizes. Most woodworkers use the 6” model, simply because it’s easiest to carry around. Also, most of the stock you’ll use will be no bigger than 6” wide, so 12” is overkill. The layout square is a triangle that you can use to mark square cuts on stock. Once you measure the length of the cut, you line up the layout square with the edge of the board. The short side will give you a straight, square cut across the end grain. You can also measure off angles with the layout square. This helps when you’re trying to measure for a bevel on a table saw, or marking a cut for a miter saw. You can even use your layout square to determine an existing angle. Just be sure to buy one made of metal. The plastic ones are not only fragile, but they also can warp, making them pretty useless.
Add the ultimate in convenience, power, and safety to your router lift! JessEm's new soft-start, 3.25hp router motor puts the variable speed control and power switch at your fingertips. The control panel attaches directly to INCRA Router Table Stands and is easily adapted to other router table installations. Compatible with router lifts designed to accept the Porter Cable 7518 motor. This router is not for hand held use.
I've worn this apron in my studio/workshop several times now, and I really like it. It's more expensive than some, but the materials and construction are first-rate. I rarely give five stars, but the workmanship on this apron is impressive. The fabric is substantial and, although a bit stiff at present, comfortable to wear. The strap and grommet system is pretty clever, allowing a good fit for most, I would think. I'm a 5'-7" not-skinny woman, and I'm able to cross the straps at the small of my back and then tie them in front, so I'm guessing there would be plenty of strap length for bigger men. The straps sit comfortably on my shoulders. And all the pockets are great! 

Okay, let’s stain this beast. I should explain that we used Rustoleum’s Dark Walnut Ultimate Wood Stain, but we did it wrong. We failed to mix it well before applying it, resulting in a color we really liked–but not the color this stain is designed to create. When we came back to do a second coat, we stirred it well, resulting in a coat that looked like purple paint. I had to sand it off and start over. So, don’t follow my lead here–follow the can’s directions and TEST before staining all of your new masterpiece!
I've worn this apron in my studio/workshop several times now, and I really like it. It's more expensive than some, but the materials and construction are first-rate. I rarely give five stars, but the workmanship on this apron is impressive. The fabric is substantial and, although a bit stiff at present, comfortable to wear. The strap and grommet system is pretty clever, allowing a good fit for most, I would think. I'm a 5'-7" not-skinny woman, and I'm able to cross the straps at the small of my back and then tie them in front, so I'm guessing there would be plenty of strap length for bigger men. The straps sit comfortably on my shoulders. And all the pockets are great!
While the top is drying, measure the thickest portion. Add 1/16” to this measurement and mark a horizontal line with a framing square across the tops of the table legs. This line marks the gutter structure mounting depth. Legs will protrude 1/16” above the plane of the tabletop. Ask a helper to hold the leg tight to the inside corner of the gutter structure with the mark at the top of the gutter. Drive at least two wood screws through the inside face of the gutter into the sides of the leg.
The Bosch Max FlexiClick 5-in-1 Drill/Driver System has one tool and five attachments. That means it can perform all kinds of tasks, like: screw-driving, drilling, right angle drilling/driving and offset driving close to edges. This tool/tools isn’t going to replace a deck builder’s 20v impact driver and drill, but it might be a great option for those smaller project that require a bunch of different operations, like knocking off a punch list at the end of a build-out. If you’re moving around and don’t have the space to haul around a bunch of dedicated tools this might be just what you’re looking for. The Bosch 5-in-1 Drill Driver System is available online and in home centers for $199.00.
I purchased these gloves for work, which involves handling and packing several (thousand) books everyday. When they arrived, they were a little too big for my smallish hands. I figured I would use them anyway to spare my sore fingers, and for the week I used these my hands were safe and papercut-free! The grip dots were secure and helped to grip even thin sheets of paper. The fingers bunched up a bit, but that's to be expected from oversized gloves.

I am so glad to see this. It is exactly what I have been looking for. I have had a similar idea in my head for years but didn't know how to bring it together, and I wasn't sure how it would actually turn out. Yours is beautiful. It is nice to start with an idea of how the project will actually look when I am done. My table is 25 years old with a laminate top. The reason I want to cover instead of replacing it does that it is the first purchase my husband and I made together. It has seen 25 years of abuse by three little (now big!) boys and by me, the messy crafter. But I cannot imagine ever getting rid of this table. Plus it's not like I'm going to get less messy, so investing in an expensive table would be crazy. I love how I can take this top off and still do the messy damaging things on it. I am bookmarking this and if I ever get around to actually doing it LOL, I will send you pics
Diablo's 3 piece Adjustable Cabinet Router Bit Set Diablo's 3 piece Adjustable Cabinet Router Bit Set features a rail and stile bit set and a Double Shear raised panel bit. Featuring TiCo carbide with titanium these bits provide a long cutting life and ultra-fine finish. Perma-Shield Diablo's high performance coating reduces friction and build-up on the bits. The ...  More + Product Details Close
×