Holy Craft came up with a genius solution for a scratched and worn dining table!  If your table looks a little worse for wear, but you still plan on using it for messy situations like painting and crafting, you’ll love this wood plank tabletop cover.  Slide it on for nice dinners and entertaining company, and tuck it away when your kids use play dough! // Holy Craft on Remodelaholic
This time I surprised one of my favorite dice games and took it outside. I made a set of wooden dice in just a few hours, and instead of sitting in the room and doing nothing, we are taking our dice game out into the yard. With this set of wooden dice, dice games are becoming our favorite backyard game. Check out the step by step tutorial below so you can make your own.
​Luckily, we have also managed to find a detailed video tutorial of the Barn door project that illustrates the process of building a Barn door of your own. The steps and instructions in the video tutorial are different from the source links listed above. Actually, you can make different types of designs for your Barn door depending on which one you can afford easily and DIY on your own.
Building a bookcase or bookshelf is a fairly simple woodworking plan that you can get done in just a day or two. This is also a low-cost project as well and since the project idea is free, you don't have to worry about busting through your budget. Just follow the simple steps in the tutorial and enjoy your own company building a simple bookcase on this weekend.
Taking cabinet building to the next level I wanted to take another step in my building and see if I could build a cabinet without the use of screws. My wife found the plans in an old Woodsmith Magazine and asked me to build the largest bookcase of the set. My plan was to build the entire cabinet using dowels instead of screws, dado slots instead of pocket hole joinery and biscuit joints. Using rough oak purchased from a local lumber mill, I milled and sized the lumber to the specifications to create this book cabinet with 5 shelves. It was time to replace a number of older pine book cases in the house. Instead of using the traditional pocket hole joinery, the sides, shelves, doors and face frame were all joined using 3/8” dowels,biscuit joints, dados and glue. I used tempered glass for the doors for safety which I was able to purchase locally. The glass vendor recommended using silicone caulk to secure each pane before applying a few small mirror catches on all the sides. The doors were each hung with 3 Ball-Tip Full Back-to-Back Wrap-Around Inset Hinges. Finished with Minwax English Chestnut and homemade wiping polyurethane, this cabinet will stand the test of time and hopefully become a keepsake that is passed down through generations. *DISCLOSURE: Some of the links in this post are affiliate links. If you chose to click through and make a purchase I will earn a commission but there is no additional cost to you. It helps compensates the business for the time spent creating these posts. THANK YOU!
Leave your tabletop longer than necessary until the sanding is done, then cut to final length. Most tabletops are too wide to trim on a tablesaw, even with a crosscut sled, and this is where I use a hand-held circular saw. Clamp a guide strip so it’s square to one edge, then follow it with your saw. Repeat the process on the other end, then carefully use your hand-held belt sander to remove any blade marks on edges. It sounds like a coarse process, but you can get great results this way.
Add the ultimate in convenience, power, and safety to your router lift! JessEm's new soft-start, 3.25hp router motor puts the variable speed control and power switch at your fingertips. The control panel attaches directly to INCRA Router Table Stands and is easily adapted to other router table installations. Compatible with router lifts designed to accept the Porter Cable 7518 motor. This router is not for hand held use.
Diablo's 3 piece Adjustable Cabinet Router Bit Set Diablo's 3 piece Adjustable Cabinet Router Bit Set features a rail and stile bit set and a Double Shear raised panel bit. Featuring TiCo carbide with titanium these bits provide a long cutting life and ultra-fine finish. Perma-Shield Diablo's high performance coating reduces friction and build-up on the bits. The ...  More + Product Details Close
Rachel Teodoro and Holy-Craft.com, 2010-present. Unauthorized use and/or duplication of this material without express and written permission from this site’s author and/or owner is strictly prohibited. Excerpts and links may be used and up to one photo can posted, provided that full and clear credit is given to Rachel Teodoro and Holy Craft with appropriate and specific direction to the original content.
×