Add the ultimate in convenience, power, and safety to your router lift! JessEm's new soft-start, 3.25hp router motor puts the variable speed control and power switch at your fingertips. The control panel attaches directly to INCRA Router Table Stands and is easily adapted to other router table installations. Compatible with router lifts designed to accept the Porter Cable 7518 motor. This router is not for hand held use.
There are YouTube videos that show how to attach tabletops using both of these tried and true methods. If you don't have a router or a biscuit joiner to make the holes for the z-fasteners, you can always use a drill. For the figure-8's, you need to recess them so they're flush with the apron...so for that, you would need to use a router. If that's not somethig you can do, I suggest sticking with the Z-fasteners. Best of luck!
Hi Mitchell – Thank you for the heads up… I thought I mentioned that in that in the post, but you’re right, I didn’t. Yes, wood expands across its width, so in order to allow for expansion/contraction there should be a small gap where the edges of the boards meet the apron. You don’t need a gap where the ends of the board meet the apron because wood doesn’t really expand/contract in this direction.
This Privacy Policy covers CanadianWoodworking.com's treatment of personally identifiable information that CanadianWoodworking.com collects when you are on the CanadianWoodworking.com site, and when you use CanadianWoodworking.com's services. This policy also covers CanadianWoodworking.com's treatment of any personally identifiable information that CanadianWoodworking.com's business partners share with CanadianWoodworking.com.
For all of your wood cabinetry and joinery tools and supplies, Infinity Cutting Tools has got you covered. We offer joinery tools and accessories for making box joints, finger joints, pocket holes, dowel joinery, dovetails, and mortise-and-tenon joinery. When it comes to installing cabinet hardware like knobs, pulls, and hinges, check out our cabinet hardware installation solutions.
I've worn this apron in my studio/workshop several times now, and I really like it. It's more expensive than some, but the materials and construction are first-rate. I rarely give five stars, but the workmanship on this apron is impressive. The fabric is substantial and, although a bit stiff at present, comfortable to wear. The strap and grommet system is pretty clever, allowing a good fit for most, I would think. I'm a 5'-7" not-skinny woman, and I'm able to cross the straps at the small of my back and then tie them in front, so I'm guessing there would be plenty of strap length for bigger men. The straps sit comfortably on my shoulders. And all the pockets are great!

Copyright 2018 by Cut The Wood. CutTheWood.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Additionally, CutTheWood.com participates in various other affiliate programs, and we sometimes get a commission through purchases made through our links. 

If you’re like me, every time you wander through a big-box furniture store, you feel a little insulted. Here you are, a man, staring at relatively simple furniture, being asked to lay down large sums of money for a bookshelf, dining set, or desk. And if you know enough about wood to spot laminate and fiberboard, you’ll quickly see these expensive pieces of furniture have a shelf life (no pun intended) of about two years.
A super simple iPad Dock/stand made out of a single block of wood features an angled groove which gets to support the tablet device and a cut in a hole to revise access to the home button of your iPad. It’s possible to drill an access channel in the stand through which you can run a charging cable, although this mini stripped back iPad stand may have very limited functions.
Drill pocket holes from the outer boards to the inner board. Drilling the holes before adding screws prevents the boards from cracking. To create the holes, measure along the sides of the center board. Mark it about every 7 in (18 cm). You will need to use a very long drill bit, about 3 in (7.6 cm) wide, called a pocket hole drill bit. Drill at an angle down through the side boards and into the side of the center board every 7 in (18 cm).[4]
Probably the next most useful shop accessory is a large work table. I like to use a portable table that can be moved around the shop as needed. This particular table, which you can build by clicking on the link above, is lightweight yet sturdy and has retractable casters. When you want to move the table, simply lift each end and the casters lock into place to allow the table to roll. Once you get it into position, pull the cord on each end and the casters retract, so the table won't move.
There was a big crowd, rocking music, and a lot of excitement over the Extreme Post-it Notes at the 3M booth at the 2018 International Builders Show. Apparently these things stick to wood, hot stuff, cold stuff, wet stuff, brick, metal, plastic pipes, ladders, stair treads, flooring, the side of a truck, copper, tools, siding, co-workers, concrete, tile, drywall, asphalt, house wrap, light fixtures, switches, cabinets, leather belts, windows…well, you get the idea. Post-it Extreme Notes will be available at major retailers beginning in March 2018.
By posting on this site and forum, the poster grants to Canadian Woodworking Magazine/Website the unrestricted rights to use of the content of the post for any purpose, including, but not limited to, publishing the posted material, including images, in print or electronic form in a future issue or issues of Canadian Woodworking magazine or related Canadian Woodworking products, and to use the post for promotional purposes without further compensation, as well as the right to use the poster's name in a credit along with the post.
Now it’s time for one of the trickiest parts–attaching the side rails to the legs. I did this part on top of the tabletop, because it was the flattest surface I could find. We got the rail perfectly straight and I had my wife stand on it to keep it steady as I drilled the pilot hole through the leg and into the rail. Then we screwed in the 6″ lag screws. And I just about broke my arm trying to use a power drill with a socket to do this.
After all slots are cut, stand each board on end and coat the edge of jointed side with wood glue. Next coat the biscuits with glue. Insert biscuits in one side only of each board, then insert glued biscuits in the empty joint of the next board. Assemble planks in order until the top is complete. Don't worry about small gaps. Next, carefully lay the top down and attach pipe clamps at roughly 1' intervals. Slowly tighten each pipe clamp in a consistent fashion until the gaps disappear*. Small amounts of glue can be removed when dry; scrape up any puddled glue with a plastic putty knife. To minimize sanding later, avoid working glue into the top of the wood. Let the top set overnight.
It is becoming more popular in this DIY age for people to want to make things themselves, and we are seeing a return to woodworking as a hobby or pastime. The garage is transformed into a workshop, with a workbench a set of woodworking tools and of course a beer fridge. Beautiful handmade woodworking projects can be achieved with some practice, a good set of plans and the right woodworking tools.

There are lots of clear finishes. But for a combination of usability and durability, you can’t beat polyurethane. Oil-based poly, which dries slower than water-based, is best for beginners because it allows more working time. The other important difference is clarity: Water-based poly is absolutely colorless, while oil-based has an amber tone, which can be good or bad depending on the look you want.
×