OK, the Long Ranger’s been around since Marconi. But we love it. Simply put, this Long Ranger III Remote Dust Collector Switch is a remote system for turning on your dust collector out in the shop from whatever tool you’re operating. It plugs into the wall, you plug your dust collector into that and you’re done. Push the button on your remote and it fires right up. It’s saved us about two years and 1,300 miles of walking back and forth to the dust collector switch.
Cedar Mini Decorative Planters/Boxes Using Interlocking Dovetail Joints Having a cedar mill within an hour of my shop allows me to work with some very nice wood. While cedar can be brittle, it is wonderful to work with and makes putting these decorative boxes together a breeze. When working with cedar I am always looking for pieces that have what is known as “heartwood”. This is the red portion of the wood. When first planed or sanded, this heartwood is almost pink in color but takes polyurethane or spar finish well giving a vibrant dark red when applied. If left untreated, cedar will turn gray in direct sunlight and a dull red color from normal household light. These boxes have been treated with a wiping polyurethane mix that allows me to apply it with a cotton rag instead of a brush. It’s faster to apply, doesn’t run and dries fast enough to apply two coats in a day. So applying 5-6 coats only takes 2-3 days to accomplish. I assembled the boxes using a dovetail joint which provides both strength and decorative at the same time. A fan shaped tenon that forms a tight interlocking joint when fitted into a corresponding mortise. The dovetails on these boxes are shown on the length of the box and not the end where the handles are located. I use a dovetail jig and a router to make these joints which is more efficient. Depending on how the client will use the box I may or may not drill two holes in the bottom of the box. If they are built to be used as outside planters then I drill 2, half inch holes in the bottom for water to drain. If they are to be used inside as a table center piece or fireplace mantle decorative box, then I do not drill the hole. In the end they are strong, durable and beautiful no matter how they are used.
Be sure wood is dry. Material from a job site or floor joists that existed in a crawlspace may have high moisture content; material from a conditioned space should be dry. Wood can be dried in a kiln (ask your local lumber mill) or stored inside through the winter. If time does not permit, stack wood in a hot dry place with 1" spacers between layers. Allow to dry for a minimum of two weeks. 

This could quite possibly be the best tool on this list! Have you ever tried to get your drill in a tight spot where you absolutely had to use it and just couldn’t? Holy Moly has this happened to me like 100 times. Almost nothing is more frustrating! With this flex shaft, you can bend around corners and fit into impossibly tight spaces like a knife through hot butter! Buy this thing!!!!
You would think that a sharp tool you swing in the direction of your ankles wouldn't last long. But the adze can be traced back at least to ancient Egypt. You use the adze to shape tree trunks and square them up into beams; looks like an ax with the blade oriented on the horizontal. But with modern-day milling capabilities so much faster and easier, for the most part the adze has gone the way of the dodo.

She has permanently glued and screwed the tabletop within that four-sided, mitered frame. Attaching the skirt to the long edges of the wide boards is no problem, but fastening them to the end grain of the wide boards, as shown in the photo above, is. The builder has constricted the wide boards' movement, and as they grow or shrink in width but are held in place by those end-caps, they will warp and split, making this a short-lived piece of furniture.
From the source tutorial, you can get illustrates to the instruction about the plan. Everything is fairly described as diagrams, images, the list of supplies and tools need etc. The process to this plan is very easy to understand and follow for if you are having some basic woodworking knowledge. Make sure to collect all the supplies you need before you start with the project. You may even ask any question directly in the comment section of the tutorial post and also comment the images of your final product if you have completed it. Either way, I hope that you will manage to build this one nicely.​
If you have some basic carpentry and tool usage skills, take advantage of Ryan's custom woodworking plans and the opportunity to build a custom entertainment center yourself with entertainment center plans, media center plans and woodworking plans designed and published by Ryan. If you don't, now is a great time to start. Its not as difficult as your may think.
If you bought this superb polished table in a store, it would cost you a fortune, but our detailed instructions will help you make one for less than $100. And it looks like highly polished stone, but no-one would know it’s actually made from concrete with a wooden base. Also, you can embellish the top with leaf prints, like the table shown here, or personalize it with glass or mosaic tiles or imprints of seashells.
Using shelving in your room or kitchen is a great way to arrange and de-clutter space… I know, such ground-breaking term it is. Do not write me off yet, I just want to show you how you can build some clean floating corner shelving that appears to have no brackets. You can create them at no cost, and the hardest part of the plan is figuring out what you are going to put on these shelves when you are finished.
This could quite possibly be the best tool on this list! Have you ever tried to get your drill in a tight spot where you absolutely had to use it and just couldn’t? Holy Moly has this happened to me like 100 times. Almost nothing is more frustrating! With this flex shaft, you can bend around corners and fit into impossibly tight spaces like a knife through hot butter! Buy this thing!!!!
The result of this project is what your wife or girlfriend would call a “Rustic,” “Barn,” or “Ranch Style” dining room table. I call it a man table, because it’s made from inexpensive wood, can take a beating, and one day your grandchildren will be serving their kids Thanksgiving dinner on it. Being the man that built that table is, well, manly. I’ve found a few similar tables on Craigslist and furniture sites, starting at around $1200. That’s absurd. I built mine for less than $200, including the chairs I bought for it.
Now that you have the final dimensions for the table top, you need to choose which boards you want to use.  Because we don't have a table saw and we wanted to keep this project simple and not cut any boards lengthwise, we {and by we, I mean my husband} plugged and chugged different board sizes into his calculator to find the perfect equation. We ended up using seven 1x6 boards for the width and on the two end caps we used 1x8's. Remember, a 1x6 is not six inches wide, it's five and a half, and a 1x8 is seven and a quarter inches wide. When you are doing your math to figure out what boards you need, remember that the nominal size {1x4, 1x6, 1x8, etc} is not the actual measured dimension of the board.
What makes this JCB Teleskid machine unique is it’s one-of-a-kind telescoping boom, which gives it the ability to reach a variety of places. The Teleskid’s telescoping boom gives you eight feet of outward reach. Plus, its one armed design gives you 60 percent more visibility than similar twin-armed machines. With a fully extended boom the Teleskid can lift up to 1600 pounds. With the boom retracted that weight capacity goes up to an impressive 3695 pounds. To find out more about the Teleskid from JCB, click here.

Stanley produced this all-in-one layout tool between 1888 and the 1930s. It looks like a directional arrow from a street sign and was originally advertised as 10 tools in one (including level, depth gauge, try square, and compass). There are a few companies that make replicas, but originals can still be found on eBay for a couple hundred dollars apiece.
OK, the Long Ranger’s been around since Marconi. But we love it. Simply put, this Long Ranger III Remote Dust Collector Switch is a remote system for turning on your dust collector out in the shop from whatever tool you’re operating. It plugs into the wall, you plug your dust collector into that and you’re done. Push the button on your remote and it fires right up. It’s saved us about two years and 1,300 miles of walking back and forth to the dust collector switch.
I purchased these gloves for work, which involves handling and packing several (thousand) books everyday. When they arrived, they were a little too big for my smallish hands. I figured I would use them anyway to spare my sore fingers, and for the week I used these my hands were safe and papercut-free! The grip dots were secure and helped to grip even thin sheets of paper. The fingers bunched up a bit, but that's to be expected from oversized gloves.
Check out our most recent woodworking tools and accessory reviews below. We have thousands of satisfied customers that use our router bits, shaper cutters, router tables, and many more fine woodworking tools every day. Take a minute to read what your fellow woodworkers have to say about their experience with our company and our quality woodworking tools. All reviews are from real customers of Infinity Tools who were polled by our partners at ShopperApproved.com. More third party reviews can be found at Shopper Approved's website.
A super simple iPad Dock/stand made out of a single block of wood features an angled groove which gets to support the tablet device and a cut in a hole to revise access to the home button of your iPad. It’s possible to drill an access channel in the stand through which you can run a charging cable, although this mini stripped back iPad stand may have very limited functions.
Up to now, I had been completely focused on the upward-facing portion of the tabletop, the side that would be most visible. But as I drew nearer to the finish line, I started to doubt my earlier decision not to finish the bottom side too. So I went back and did the extra work, and though this additional step might have been unnecessary, I like to think it helped make the table fit better into its home for the summer, my front porch. All that was left now was to attach the top to the metal table. As easy as it was to finish the tabletop with Minwax, it was no mean feat to devise a way of securing the top to the base. Ultimately, the answer to my problem came in an unlikely form. On a typical day, electrical cable hardware would never have entered my mind, but as the result of a funny twist of fate—the same sort of coincidence that led me to undertake this project in the first place—these simple snap-and-click fasteners enabled me to attach the top to the base and call it day. Now, with this project under my belt, I’m starting to eye those 2x6s still lingering in my scrap pile!

There is no cost to use the database. Registering is not required. You should be able to browse the database and click through the links. Having said that, considering the fact there are so many browsers out there being used, this site's software might not allow some visitors to browse, it all depends on the Internet traffic, and your browser's compatibility.


OK, the Long Ranger’s been around since Marconi. But we love it. Simply put, this Long Ranger III Remote Dust Collector Switch is a remote system for turning on your dust collector out in the shop from whatever tool you’re operating. It plugs into the wall, you plug your dust collector into that and you’re done. Push the button on your remote and it fires right up. It’s saved us about two years and 1,300 miles of walking back and forth to the dust collector switch.
A heavy-duty hardened steel chain with hexagonal links will thwart nearly every thief with a bolt cutter. Hexagonal links (or square or trapezoidal) make it impossible for bolt cutters to get a grip. You may be tempted to buy chain by the foot at the hardware store, but it’s designed for lifting and towing, not theft resistance. Even the thick stuff is likely to have round links, and frankly, if a hardware store clerk can cut the chain easily, a thief can too.

Ridgid has a new C-style close-quarter tubing cutter that slices through both 1/2-in. and 3/4-in. tubing, which means one less tool to carry and fumble around for. The cutting wheel is spring loaded so it needs no adjustment as you spin the cutter, and the outside surface has screwdriver slots for getting leverage in tight spaces. The 1/2 – 3/4 Rigid tubing cutter costs $32 and is available at plumbing supply stores and online retailers.
If you have some basic carpentry and tool usage skills, take advantage of Ryan's custom woodworking plans and the opportunity to build a custom entertainment center yourself with entertainment center plans, media center plans and woodworking plans designed and published by Ryan. If you don't, now is a great time to start. Its not as difficult as your may think.
Aside from the privacy it offers, a latticework porch trellis is a perfect way to add major curb appeal to your home for $100 or less. The trellis shown here is made of cedar, but any decay-resistant wood like redwood, cypress or treated pine would also be a good option. Constructed with lap joints for a flat surface and an oval cutout for elegance, it’s a far upgrade from traditional premade garden lattice. As long as you have experience working a router, this project’s complexity lies mostly in the time it takes to cut and assemble. Get the instructions complete with detailed illustrations here.
This is another very interesting project. To make a similar table you need to have textured spray paint, matte black spray paint, lumber, wood boards, wheels, stain, sand paper, corner pieces, nails, bolts, nuts, washers, clamps and L brackets. First make the measurements and spray paint all the hardware including the wheels. Then make the basic box and sue nails to hold the wood pieces in place. Then use L brackets to keep them sturdy and add the bolts. Tighten the nuts into the bolts and attach the wheels.Then add the corner pieces sing nails{found on theblissfulbeeblog}.
Family Projects I was given the opportunity to build the ring bearer box for the up coming wedding of my niece. She provided me with a picture from Pinterest for an example. I said no problem. Materials Made from white oak I milled the lumber using my @ridgidtools planer and sanded it using my SuperMax tools drum sander. Then I stained it with Minwax espresso stain and finished with multiple coats of poly. To make it even more customized I used red cedar to make the first letter of the bride and groom’s names for the inside lid of the box. Project Ideas Most of my custom projects are the result of people presenting several photos of different pieces that they want combined to fit their specific need. One might show the size or depth, one might have a particular style they like, and one photo might show the wood stain they prefer. I take the time to build the plans in my drawing program and present the “new” piece to my clients for approval. It’s a great way to build just what my customers need for their home and having photos cuts down on the guesswork. Let me know if you have something you’d like built by using this form, I’d be happy to provide a free quote for you. Now it’s time to get back to the shop and make some sawdust! Disclaimer: We are now featuring affiliate links to help us fund this website. It does not cost you anything to click on the links. Thank you!
For an artisanal look, you can use woodworking hand tools. These are easy to use, lightweight and require no batteries or power cords to operate. Many hand tools are covered by multi-year or even lifetime warranties for extra protection and value. Set up your pieces with the most expertly crafted woodworking hardware, such as hinges, pulls and knobs to create a final product that you can give as a gift, sell or just display proudly.
If you can beg or borrow a pocket hole jig you dont have to predrill holes. I haven’t done a table top other than a workbench(Plywood!) but I have done cabinets and beds. The Kreg jig makes joining easy. A lighter stain colour would cut down on the grain marks, or a heavier application like an espresso stain. I will throw you a pic when I finish my table and show you what I mean.
Screwdrivers are another must-have in the woodworker’s set of hand tools. Not only will you need Phillips and slot, or flathead screwdrivers, you’ll need star drivers and Torx drivers, too. A quality construction is vital to a good set of screwdrivers. So many of them are made out of soft metal, and the first time you put any “oomph” behind them, they strip out, becoming absolutely useless.
Before doing anything else, I measured the metal garden table to figure out what size the tabletop would need to be. With those dimensions in mind, I went hunting for scraps. Somewhere in my collection, I was able to find the right combination of 2×4 boards to cover the measured surface area. (Note: If you’ve got a large, motley assortment of wood, you might find it painstaking to cull the pile and piece together suitable boards. To make quicker work of the process, I suggest cutting a template out of cardboard and using it to test different arrangements.) For my part, starting with five 2×4 boards, all roughly the same length, I had to make just a handful of cuts with the circular saw to end up with exactly the right amount of material. In the above photo, those dozen smaller pieces may seem haphazardly strewn about, but when combined, they fit together perfectly to form a tabletop of the desired shape and size.
By video tutorial, you will get step by step process instructions of making a nice wooden folding sling chair from scratch. However, my first wooden chair was not the best one, but it was good enough to motivate me to make some more folding chairs like this one. If I can make this, you too can make one yourself. You can browse the internet for more folding sling chairs ideas and start making one now.
Im am so glad you posted this! I bought a cheap dining room table from good will to use for my desk, it has a leaf in the middle to make it longer. I wanted to glue the leaf to the other two sides and thin fill in the holes with wood filler and I was advised by mom friend that it wouldnt work, but now I have proof cant wait to try it out!!! thanks 🙂

By posting on this site and forum, the poster grants to Canadian Woodworking Magazine/Website the unrestricted rights to use of the content of the post for any purpose, including, but not limited to, publishing the posted material, including images, in print or electronic form in a future issue or issues of Canadian Woodworking magazine or related Canadian Woodworking products, and to use the post for promotional purposes without further compensation, as well as the right to use the poster's name in a credit along with the post.


This Privacy Policy covers CanadianWoodworking.com's treatment of personally identifiable information that CanadianWoodworking.com collects when you are on the CanadianWoodworking.com site, and when you use CanadianWoodworking.com's services. This policy also covers CanadianWoodworking.com's treatment of any personally identifiable information that CanadianWoodworking.com's business partners share with CanadianWoodworking.com.


If you sand through the polyurethane and remove some stain, you can touch up with more stain. But the repair won’t be perfect, so take pains to avoid that mistake. Sand very lightly after the first coat, just enough to remove the dust whiskers. After the second coat, you can sand a little harder to flatten larger flaws. Always be careful around the edges of the table; that’s where it’s easiest to sand through.
×