For all of your wood cabinetry and joinery tools and supplies, Infinity Cutting Tools has got you covered. We offer joinery tools and accessories for making box joints, finger joints, pocket holes, dowel joinery, dovetails, and mortise-and-tenon joinery. When it comes to installing cabinet hardware like knobs, pulls, and hinges, check out our cabinet hardware installation solutions.
The next important hand tool for the woodworker is an accurate tape measure. Get a retractable one that is at least 25 feet long. Any longer than that, and you start having problems getting it to roll back up. Since measurements on large scale projects can be very susceptible to even the most minute measurement variations, you’ll want to make sure the “hook” or tab at the end of the is firmly attached, with no give. When they get loose, you’ll have as much as 1/8” variation in your measurements. This can add up to some severe accuracy problems in the long run.
A heavy-duty hardened steel chain with hexagonal links will thwart nearly every thief with a bolt cutter. Hexagonal links (or square or trapezoidal) make it impossible for bolt cutters to get a grip. You may be tempted to buy chain by the foot at the hardware store, but it’s designed for lifting and towing, not theft resistance. Even the thick stuff is likely to have round links, and frankly, if a hardware store clerk can cut the chain easily, a thief can too.
This could quite possibly be the best tool on this list! Have you ever tried to get your drill in a tight spot where you absolutely had to use it and just couldn’t? Holy Moly has this happened to me like 100 times. Almost nothing is more frustrating! With this flex shaft, you can bend around corners and fit into impossibly tight spaces like a knife through hot butter! Buy this thing!!!!
Another fairly inexpensive option for making a table top is using a stain grade 3/4″ plywood. cut the 4 x 8 sheet in half (2- pcs, 4 x 4). Spread wood glue one and place and clamp the other on top. Once the glue has dried, it can be cut with a jig saw to the round shape, or if you have access to a router, make a “circle cutter” by mounting the router on a thin piece of wood, (1/4 x 6 x 60″) and putting pivot hole at a distance of 1/2 the diameter of the desired table. (from the side of the router bit to the pivot hole. Put a small hole in the underside of the table top as close to the center as possible. (not all the way through) and use something like a nail as a pivot. Use a straight bit and cut a perfect circle. The stain grade plywood usually has a pretty good stain surface and the construction of the plywood makes it pretty stable. After cutting the edge may have some minor voids, which can be filled with wood putty and sanded nice and smooth. The results can be a nice stained or painted surface.

Yes Seriously! You can build an easy bed frame yourself without any other’s help. As everyone knows the starting point of any bedroom is a gorgeous bed. However, you also need something that lets you enjoy peaceful slumber in comfort and warmth, but since the bed took as the focal point of the room, you may need something that looks really good too.
Every woodworker needs a couple of levels. You probably won’t need one of the 6-foot levels used in construction, but 48” is a good length for many of the woodworking projects you’ll do. Usually, you’ll also need an 8” level too, usually known as a torpedo level. You’ll check the level and plum of your construction. Level means horizontal, and plumb is vertical.
There are YouTube videos that show how to attach tabletops using both of these tried and true methods. If you don't have a router or a biscuit joiner to make the holes for the z-fasteners, you can always use a drill. For the figure-8's, you need to recess them so they're flush with the apron...so for that, you would need to use a router. If that's not somethig you can do, I suggest sticking with the Z-fasteners. Best of luck!

This is another wood table but this time with a more elaborate design. Instead of using a large log, this time you’ll need several small ones. The idea is to cut them to the same height and to try to create a mosaic with them. You can glue them together and you can also wrap a piece of rope or something similar around them. You should be able to create an original coffee table.
When it comes to choosing a finish there are two main choices. The typical approach of stain and urethane creates a smooth, wipeable surface, but when that finish eventually wears through, there’s no way of repairing it attractively. Sanding back to bare wood and refinishing is the only way to make it respectable again. Oil and wax finishes, on the other hand, take more time to apply initially, but they’re easily repaired and rejuvenated with the tabletop in place. Regular reapplication works just fine. 

Every carpenter or woodworker has needed a pair of sawhorses at some point. I've used them for hundreds of tasks, including as a sturdy base for a table saw. This set of saw horses is stackable, very solid (they will hold as much as 500 pounds each if properly built) and very easy and inexpensive to build. Once you have a set, you'll find hundreds of uses for them, not only in the wood shop but around the house as well.

Manufacturers that produce woodworking tools and materials have got into the content creation game, too, and some will share woodworking plans online. Minwax and Ryobi, for example, provides their plans free of charge, and Rockler offers their woodworking plans for a fee. Seek them out along with the other blogs and you’ll have a handy list of resources you can turn to for any project.
There are lots of clear finishes. But for a combination of usability and durability, you can’t beat polyurethane. Oil-based poly, which dries slower than water-based, is best for beginners because it allows more working time. The other important difference is clarity: Water-based poly is absolutely colorless, while oil-based has an amber tone, which can be good or bad depending on the look you want.
The Wilton ATV All-Terrain Vise is a tool for those of you who work out of your pickup at job sites and need a serious on-site vise. And this vise is worth the price! It slips into any 2-in. receiver hitch and has a sizable flat anvil area for pounding. It comes with a bracket for attaching to any sturdy surface, such as a trailer, if you don’t want to use your truck.
Cut off a 21-in.-long board for the shelves, rip it in the middle to make two shelves, and cut 45-degree bevels on the two long front edges with a router or table saw. Bevel the ends of the other board, cut dadoes, which are grooves cut into the wood with a router or a table saw with a dado blade, cross- wise (cut a dado on scrap and test-fit the shelves first!) and cut it into four narrower boards, two at 1-3/8 in. wide and two at 4 in.
Now, the project starts to get really interesting. While I knew that I would use pocket-hole joinery (my latest obsession) to assemble the tabletop, I couldn’t decide how to finish the wood. There were three different cans of Minwax Gel Stain on my shelf, in three different colors—Hickory, Cherrywood, and Honey Maple. In my head, I could make a credible argument in favor of each one. And though it would have helped to know where the table would eventually go, that was another question I couldn’t answer. Then it hit me: Rather than choose one stain, why not use them all? After all, I was constructing the tabletop from scraps, so it was going to have a homemade, mosaic look no matter what. In the end, using multiple stains would emphasize the rustic effect the table was going to achieve. Perfect! From there, having fought my way to a project plan, the rest came easy. Read on to see how I built the tabletop, then stained and sealed it with Minwax.
If you have some basic carpentry and tool usage skills, take advantage of Ryan's custom woodworking plans and the opportunity to build a custom entertainment center yourself with entertainment center plans, media center plans and woodworking plans designed and published by Ryan. If you don't, now is a great time to start. Its not as difficult as your may think.
Bought 2 of these, one for the wife and one for me. We have a project we are doing that required cutting lots of MDF(medium density fiberboard) which is not good for you to breathe or get in your eyes (very tiny particles). I picked these because people said they worked well with glasses (which i wear) and because they had full protection from flying debris and also from the airborne dust.
Hanging upper cabinets is a tough task for one person. Having a lifting buddy to help is usually a good idea but costs extra. Little Hands HD is perfect for the guy who mostly works alone. The 6 x 6-in. base keeps the cabinets stable, and each lift can handle 150 lbs. The lever action can be raised a tiny fraction of an inch at a time, but sneak up on your target height because lowering the lifts isn’t quite as easy.
Hi Mitchell – Thank you for the heads up… I thought I mentioned that in that in the post, but you’re right, I didn’t. Yes, wood expands across its width, so in order to allow for expansion/contraction there should be a small gap where the edges of the boards meet the apron. You don’t need a gap where the ends of the board meet the apron because wood doesn’t really expand/contract in this direction.
The Story of the Farmhouse Table with a Race Track While working my day job one of my managers came to my desk and said “I need your help”. Come to find out she ordered a farmhouse table and bench on Etsy. However the person she ordered it from fell off the face of the earth and left her without a table or her money (Etsy made good on it for her). The reason she ordered the table was because of the three legged bench. She has a young son and was concerned that he would turn over a two legged bench. This one appeared to give her the stability that she wanted. My reply, “I can help!” After seeing the picture of the table she ordered I told her to give me a few days and I could find her an alternative. So I went out to one of my trusted bloggers, Rogue Engineer and found the table I wanted to build. Please check out his site and follow him on social media. After getting her approval of the style and layout, we agreed on a price and some minor adjustments to the plans. She only wanted a 7 foot table and she only wanted one bench, but that bench needed a third leg. So I made the size adjustments and quoted the table. Now the “Curve” A couple of days after we agreed on the project my client called and said she had an idea on the way to work. She needed to find a way to get her son to the dinner table. “Can I add a 1½” wide by 1/8th inch deep race track around the top of the table?” After I caught my breath and recovered I gave her some alternative ideas to avoid creating a race track into what I knew was going to be a beautiful table. She was convinced this is what she wanted, so I said well, this is why we call ourselves Bayne CUSTOM Woodworking. So I agreed and then the adventure began. The Build Instead of recreating what Rogue Engineer already did I will refer you to his free plans on his site. See the link in the opening paragraph.  He will provide the materials list needed. Below I will outline the changes I made and how I built the table and bench. While not huge changes, there are some that I made to meet the client’s requests and some to add my own unique style. The plans call for a table that is 110” while I made mine to fit the client request of 84”. Because I trimmed my boards I ended up with a 40” wide top instead of a 42” wide. She wanted only one bench so I made an 80” bench with 3 legs instead of the 2 legged bench. Let me also state up front that I rarely, if ever, use pine to build anymore, but I did use it on the job because
If you’re looking for ways to rehab an old table, this charred wood table is a fairly simple project that requires just a few hours of work. I used the charred appearance boards to create a new tabletop for my porch table. The old table top needed to be painted or replaced, so I thought these boards would make for a gorgeous, fresh look for the table. The table base is actually an antique from Europe. I love rescuing old pieces. Using the charred wood for a new table top is the perfect way to update it and make it usable again.
With so many woodworking tool choices and options, we created this section to highlight the latest and greatest among the new woodworking tools recently added to our site. Our selection of Woodworking Tools is always expanding with one goal in mind - helping you become a better woodworker! If you are new to woodworking or just adding to your woodworking tools, here's an interesting article from our woodworking newsletter on what tools to buy - What Woodworking Tools would I buy now? From time to time we also feature new tool releases on our Woodworking Tool Sale page so be sure to take a peek...you might find a super special while you are at it! Even more deals at Half-Price Woodworking Tools!
Example Entertainment Center: $25 for plans + $750 for materials + $1200 for good quality tools = $1975. Less than a few grand! Of course you don't have to buy brand new tools; search the sale lists online (i.e. Craigslist, Freecycle.org, etc.) in your area. You are sure to find some good deals on power tools and even materials! (A good set of tools includes a table saw, miter saw, nail gun and compressor and four piece cordless tool set.)
You might be able to reproduce the same concept that the table with leaves has. Instead of putting the clips on the underside of the table (since that would not allow it to lay flat over the existing table) perhaps you could get smaller hooks and place it on the underside where it overhangs on the side. Would be a little more work, but definitely cheaper than a new table. 😉
It is becoming more popular in this DIY age for people to want to make things themselves, and we are seeing a return to woodworking as a hobby or pastime. The garage is transformed into a workshop, with a workbench a set of woodworking tools and of course a beer fridge. Beautiful handmade woodworking projects can be achieved with some practice, a good set of plans and the right woodworking tools.

The Story of the Farmhouse Table with a Race Track While working my day job one of my managers came to my desk and said “I need your help”. Come to find out she ordered a farmhouse table and bench on Etsy. However the person she ordered it from fell off the face of the earth and left her without a table or her money (Etsy made good on it for her). The reason she ordered the table was because of the three legged bench. She has a young son and was concerned that he would turn over a two legged bench. This one appeared to give her the stability that she wanted. My reply, “I can help!” After seeing the picture of the table she ordered I told her to give me a few days and I could find her an alternative. So I went out to one of my trusted bloggers, Rogue Engineer and found the table I wanted to build. Please check out his site and follow him on social media. After getting her approval of the style and layout, we agreed on a price and some minor adjustments to the plans. She only wanted a 7 foot table and she only wanted one bench, but that bench needed a third leg. So I made the size adjustments and quoted the table. Now the “Curve” A couple of days after we agreed on the project my client called and said she had an idea on the way to work. She needed to find a way to get her son to the dinner table. “Can I add a 1½” wide by 1/8th inch deep race track around the top of the table?” After I caught my breath and recovered I gave her some alternative ideas to avoid creating a race track into what I knew was going to be a beautiful table. She was convinced this is what she wanted, so I said well, this is why we call ourselves Bayne CUSTOM Woodworking. So I agreed and then the adventure began. The Build Instead of recreating what Rogue Engineer already did I will refer you to his free plans on his site. See the link in the opening paragraph.  He will provide the materials list needed. Below I will outline the changes I made and how I built the table and bench. While not huge changes, there are some that I made to meet the client’s requests and some to add my own unique style. The plans call for a table that is 110” while I made mine to fit the client request of 84”. Because I trimmed my boards I ended up with a 40” wide top instead of a 42” wide. She wanted only one bench so I made an 80” bench with 3 legs instead of the 2 legged bench. Let me also state up front that I rarely, if ever, use pine to build anymore, but I did use it on the job because
Drilling into tile is sort of a three hand operation: hold the drill, spray the water, and make sure the water stays were it’s supposed to. The Aqua Shot from Miyanaga is a great solution to your ceramic drilling woes. The Aqua Shot drill bit has a built-in water tank that feeds water to the drill as you operate, making the whole process much smoother. Just load the chamber up with water, flip a switch and drill away. The Aqua Shot works with impact drivers and the individual tips can be replaced when they get worn out without having to replace the whole tool. The Aqua Shot is available online for $82.80. Click here for a video of the Aqua Shot in action.
What makes this JCB Teleskid machine unique is it’s one-of-a-kind telescoping boom, which gives it the ability to reach a variety of places. The Teleskid’s telescoping boom gives you eight feet of outward reach. Plus, its one armed design gives you 60 percent more visibility than similar twin-armed machines. With a fully extended boom the Teleskid can lift up to 1600 pounds. With the boom retracted that weight capacity goes up to an impressive 3695 pounds. To find out more about the Teleskid from JCB, click here.
You can also use Google image search to research a project. Unlike the PDF search, the image search provides a photo of what the project will look like, which is helpful in determining if you want to pursue building it. By doing an image search for how to build a step stool, you will have a ton of options that all lead to woodworking plans of various quality. (The how to part of these is important—otherwise you’ll just get pictures of step stools.)
Here’s an old woodworking adage I enjoy ignoring: “measure twice, cut once.” Honestly, I measure nonce and cut thrice. I often eyeball it. I use pieces I’ve already cut to measure what I need to cut. It’s not a great habit, but I prefer it to measuring everything. And the results usually aren’t that different. At least that’s what I tell myself. I ended up having to sand down the ends of the 2×12’s running the length of the table (where they meet the aprons) because they weren’t exactly the same length.
×