She has permanently glued and screwed the tabletop within that four-sided, mitered frame. Attaching the skirt to the long edges of the wide boards is no problem, but fastening them to the end grain of the wide boards, as shown in the photo above, is. The builder has constricted the wide boards' movement, and as they grow or shrink in width but are held in place by those end-caps, they will warp and split, making this a short-lived piece of furniture.
Clamp curved caul edges inwards so they align tabletop boards in the middle, then torque up the main clamps to draw the boards together. If the width of boards you’re using allow it, pre-glue boards for your tabletop in sections that are just narrow enough to fit within your thickness planer. Run these through the planer to clean and level the glue joints, then move back to clamps for final glue up. Working in stages like this reduces the number of glue joints you need to sand smooth and level later.
If you have some basic carpentry and tool usage skills, take advantage of Ryan's custom woodworking plans and the opportunity to build a custom entertainment center yourself with entertainment center plans, media center plans and woodworking plans designed and published by Ryan. If you don't, now is a great time to start. Its not as difficult as your may think.

A lot of woodworkers share their projects through their own blogs or YouTube channels. In fact, we’ve shared many of them here before, including, Woodworking for Mere Mortals, The Wood Whisperer, Matthias Wandel, April Wilkerson, Sawdust Girl, House of Wood, FixThisBuildThat, Pneumatic Addict, Build-Basic, Rogue Engineer, Her Tool Belt, and Ana White. The best YouTube woodworkers create great videos, but also provide a complete blog post with a cut list, tools, materials, and instructions. Find your favorites and save them for when you’re doing your searches.

If planks are slightly cupped or twisted, have them planed at a local millwork shop or borrow a tabletop planer and tackle the job yourself. If planing yourself, first check planks for and remove nails and excess dirt*. Run planks though the planer, stripping a small amount of wood from each side as you plane. While the board is going through the planer, manually adjust the depth of the cut to compensate for irregular thickness (or twist) over the board’s length. You can hurt yourself or damage the board or planer if you do not manually adjust as you go. Keep running boards through the planer until the blade has lightly stripped each surface. Next, rip boards on a table saw to create straight edges; planks do not have to be identical in width.


The most commonly purchased claw hammer is the 20 oz. size. It’s heavy enough to easily drive nails but easily manipulated when pulling nails. While wooden handles are picturesque, they may not stand up to the strain if you have to pull a lot of nails. Hammers with a steel handle, or even fiberglass, will be stronger. However, these won’t absorb the vibrations from driving nails the way a hickory handle will. You’ll also need to make sure the fiberglass and metal handles have a rubberized grip for control and comfort. If you’re going to be driving a lot of nails, the wooden handled hammer will be better for reducing stress on your hand, and wrist, too.
There was a big crowd, rocking music, and a lot of excitement over the Extreme Post-it Notes at the 3M booth at the 2018 International Builders Show. Apparently these things stick to wood, hot stuff, cold stuff, wet stuff, brick, metal, plastic pipes, ladders, stair treads, flooring, the side of a truck, copper, tools, siding, co-workers, concrete, tile, drywall, asphalt, house wrap, light fixtures, switches, cabinets, leather belts, windows…well, you get the idea. Post-it Extreme Notes will be available at major retailers beginning in March 2018.
Example Entertainment Center: $25 for plans + $750 for materials + $1200 for good quality tools = $1975. Less than a few grand! Of course you don't have to buy brand new tools; search the sale lists online (i.e. Craigslist, Freecycle.org, etc.) in your area. You are sure to find some good deals on power tools and even materials! (A good set of tools includes a table saw, miter saw, nail gun and compressor and four piece cordless tool set.)
This time I surprised one of my favorite dice games and took it outside. I made a set of wooden dice in just a few hours, and instead of sitting in the room and doing nothing, we are taking our dice game out into the yard. With this set of wooden dice, dice games are becoming our favorite backyard game. Check out the step by step tutorial below so you can make your own.
This tool is specialized for the task of making shingles. The strange name comes from the antiquated word "froward," which means "away," in reference to the direction that the tool cuts. To use it, place the froe, blade down, on the edge of a log length, then hit the top of the blade with a wooden club, forcing the froe into the log. Next, pull the handle toward you and pry off a thin slice of the log. Voilà... shingle! Since buying a box of square-edged shingles is significantly less effort than making each and every one by hand, this tool has long since passed its heyday. But it still can be used to build up the kindling pile.

Hanging upper cabinets is a tough task for one person. Having a lifting buddy to help is usually a good idea but costs extra. Little Hands HD is perfect for the guy who mostly works alone. The 6 x 6-in. base keeps the cabinets stable, and each lift can handle 150 lbs. The lever action can be raised a tiny fraction of an inch at a time, but sneak up on your target height because lowering the lifts isn’t quite as easy.
All content on this blog is the property of Just the Woods, LLC. You are welcome to share my content (to include one photo only) as long as you provide a link back the original post. DO NOT copy entire posts, or crop, edit, or remove watermarks from photos without written permission from me first. Sharing a post from Just the Woods in a capacity where YOU will be compensated is not permitted. Thank you!

Before doing anything else, I measured the metal garden table to figure out what size the tabletop would need to be. With those dimensions in mind, I went hunting for scraps. Somewhere in my collection, I was able to find the right combination of 2×4 boards to cover the measured surface area. (Note: If you’ve got a large, motley assortment of wood, you might find it painstaking to cull the pile and piece together suitable boards. To make quicker work of the process, I suggest cutting a template out of cardboard and using it to test different arrangements.) For my part, starting with five 2×4 boards, all roughly the same length, I had to make just a handful of cuts with the circular saw to end up with exactly the right amount of material. In the above photo, those dozen smaller pieces may seem haphazardly strewn about, but when combined, they fit together perfectly to form a tabletop of the desired shape and size.
Add the ultimate in convenience, power, and safety to your router lift! JessEm's new soft-start, 3.25hp router motor puts the variable speed control and power switch at your fingertips. The control panel attaches directly to INCRA Router Table Stands and is easily adapted to other router table installations. Compatible with router lifts designed to accept the Porter Cable 7518 motor. This router is not for hand held use.
Here’s a traditional Swedish farm accessory for gunk-laden soles. The dimensions are not critical, but be sure the edges of the slats are fairly sharp?they’re what makes the boot scraper work. Cut slats to length, then cut triangular openings on the side of a pair of 2x2s. A radial arm saw works well for this, but a table saw or band saw will also make the cut. Trim the 2x2s to length, predrill, and use galvanized screws to attach the slats from underneath. If you prefer a boot cleaner that has brushes, check out this clever project.
Some tools that are required for this project are Miter saw, drilling machine, pencil, tape measure, screws, etc. Those, who prefer a video tutorial instead, can visit the below link to a YouTube video tutorial that illustrates the process of creating a DIY Beer Bottle Crate. The video tutorial explains every step properly so that anyone can make a Beer bottle crate easily.

Copyright 2018 by Cut The Wood. CutTheWood.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Additionally, CutTheWood.com participates in various other affiliate programs, and we sometimes get a commission through purchases made through our links.


Personally identifying information is information that can be used to identify who you are such as: name, mailing address, email address. To enter certain areas of the site, you will be required to register and provide information about yourself. This information is for the purposes of Canadian Woodworking and helps us to tailor the site to best meet the needs of our audience. 
The next part of the custom woodworking transaction is a visitation to the actual site where the furniture is going to be placed. The woodworker determines if the design is doable. If it is, he advises the client of the final cost. Once the design is approved and the contract is signed, the construction of the project can begin. Some woodworkers require advance payment before the construction can commence.

Okay, let’s stain this beast. I should explain that we used Rustoleum’s Dark Walnut Ultimate Wood Stain, but we did it wrong. We failed to mix it well before applying it, resulting in a color we really liked–but not the color this stain is designed to create. When we came back to do a second coat, we stirred it well, resulting in a coat that looked like purple paint. I had to sand it off and start over. So, don’t follow my lead here–follow the can’s directions and TEST before staining all of your new masterpiece!

×