For all of your wood cabinetry and joinery tools and supplies, Infinity Cutting Tools has got you covered. We offer joinery tools and accessories for making box joints, finger joints, pocket holes, dowel joinery, dovetails, and mortise-and-tenon joinery. When it comes to installing cabinet hardware like knobs, pulls, and hinges, check out our cabinet hardware installation solutions.
The Wilton ATV All-Terrain Vise is a tool for those of you who work out of your pickup at job sites and need a serious on-site vise. And this vise is worth the price! It slips into any 2-in. receiver hitch and has a sizable flat anvil area for pounding. It comes with a bracket for attaching to any sturdy surface, such as a trailer, if you don’t want to use your truck.
If you want your table top -- any table top -- to actually ast without bowing/cupping/twisting, you MUST attach it in a manner that allows for seasonal wood movement. Wood is an organic product, and it naturally expands and contracts with changes in temperature and humidity. I'll post link below to a couple of options that you can cheaply buy which will allow you to securely attach a tabletop while still giving the wood the flexibility to move with the seasons. When you buy decently-made furniture at a store, they all accommodate for this one way or another. Don't just screw the top down to the legs or the skirt...you'll regret it later on.
Keep your woodworking tools and knives razor-sharp with our wide variety of sharpening supplies and accessories. We have what you need for jointer and planer knife sharpening. For sharpening plane irons and chisels, we supply a variety of diamond and waterstones, the Infinity Sandpaper Sharpening System, and honing guides. Our power sharpening systems include the Worksharp Knife Sharpeners, Ken Onion edition for the sharpest knives in the drawer.
A layout square, or combination square, comes in 6” and 12” sizes. Most woodworkers use the 6” model, simply because it’s easiest to carry around. Also, most of the stock you’ll use will be no bigger than 6” wide, so 12” is overkill. The layout square is a triangle that you can use to mark square cuts on stock. Once you measure the length of the cut, you line up the layout square with the edge of the board. The short side will give you a straight, square cut across the end grain. You can also measure off angles with the layout square. This helps when you’re trying to measure for a bevel on a table saw, or marking a cut for a miter saw. You can even use your layout square to determine an existing angle. Just be sure to buy one made of metal. The plastic ones are not only fragile, but they also can warp, making them pretty useless.
The next important hand tool for the woodworker is an accurate tape measure. Get a retractable one that is at least 25 feet long. Any longer than that, and you start having problems getting it to roll back up. Since measurements on large scale projects can be very susceptible to even the most minute measurement variations, you’ll want to make sure the “hook” or tab at the end of the is firmly attached, with no give. When they get loose, you’ll have as much as 1/8” variation in your measurements. This can add up to some severe accuracy problems in the long run.
We recently upgraded a wheelbarrow with Simply Dump It pivoting handles. They slid right over the handles and took about five minutes to install. If you’re tall, you probably hunch over when you roll your wheelbarrow around the yard so you don’t end up nose-diving the wheel guard/brace into the ground, resulting in messy spills and the occasional expletive. The Simply Dump It handles raise the grip location a few inches, which lowers the handles, which in turn raises the front wheel brace. The handles not only prevent sudden stopping syndrome but also make the wheelbarrow easier to control, especially on rough terrain. And the pivoting action all but eliminates the awkward torque on your wrists when you empty the wheelbarrow. You can get Simply Dump It handles online.
OK, the Long Ranger’s been around since Marconi. But we love it. Simply put, this Long Ranger III Remote Dust Collector Switch is a remote system for turning on your dust collector out in the shop from whatever tool you’re operating. It plugs into the wall, you plug your dust collector into that and you’re done. Push the button on your remote and it fires right up. It’s saved us about two years and 1,300 miles of walking back and forth to the dust collector switch.
Here’s an old woodworking adage I enjoy ignoring: “measure twice, cut once.” Honestly, I measure nonce and cut thrice. I often eyeball it. I use pieces I’ve already cut to measure what I need to cut. It’s not a great habit, but I prefer it to measuring everything. And the results usually aren’t that different. At least that’s what I tell myself. I ended up having to sand down the ends of the 2×12’s running the length of the table (where they meet the aprons) because they weren’t exactly the same length.
This is another wood table but this time with a more elaborate design. Instead of using a large log, this time you’ll need several small ones. The idea is to cut them to the same height and to try to create a mosaic with them. You can glue them together and you can also wrap a piece of rope or something similar around them. You should be able to create an original coffee table.
Breaking down heavy sheet-goods on a jobsite table saw is difficult, and dang near impossible when working alone. That’s where a track saw comes in handy. A good quality track saw can produce cabinet saw results out on any job. Now, this portable tool is even more portable. The FESTOOL TSC 55 is a cordless saw that has the same features and performs just as well as FESTOOL’s corded saw, including the cut capacity and blade speed. It also has a collection bag that actually works, collecting up to 90% of the dust. The batteries are compatible with other FESTOOL products and the saw runs on their standard tracks.
A magnetized screwdriver or driver bit makes starting screws a lot easier. It’s like having an extra hand to hold the screw. We also like to magnetize a screwdriver when working with tiny screws that are nearly impossible to find if you drop them (been there?). You can use a magnetic bit holder in most cases, but not in tight quarters. Instead, you can just magnetize the bit. We’ve even magnetized tweezers to help pick up tiny parts.
Relax and enjoy your outdoor space with this smart patio combo consisting of a sofa and chair. You can adjust the size completely to make it fit perfectly onto your patio or deck, and both the sofa and chair have arms that double as trays for al fresco dining. And you can make your own cushions to fit, or use shop-bought ones and add your own ties, if necessary.
Woodworkers are a social bunch, and there are a few popular forums where people share thoughts on tools, discuss technique at length, and—of course—upload their plans. Some of the most active online woodworking communities include Lumberjocks, Woodworking Talk, Wood Magazine, WoodNet, Kreg, and Sawmill Creek. Search those to see if they have what you’re looking for (either with their built-in search tool or with Google’s site-specific search, e.g. site:lumberjocks.com side table).
PROCESSING NOTES: No matter how easy I have tried to make following these media center plans and constructing them, if you find it overwhelming to attempt the project or operate the basic tools necessary for completion, get help. Contact your local supplier to see if sheet goods can be ripped to fit your car trunk. The possibility of ordering all the parts ready for assembly is also available. Most importantly, when you set off to build your project, help is only an email message away.
Making a garden arched footbridge out of some wood boards can be fun, hard working plan and also it’s quite rewarding. We are providing the project tutorial for how to build an arched footbridge without rails or having rails. If you take your hands of work and have some basic woodworking skills you can easily build this type of bridge. While this garden bridge is too small to walk over but it can make a really stunning addition to your lush yard or garden.
3. Sand off the corners of the long edges of the top side. Another personal preference. When you glue the boards together, this will help break up the top so that it looks like it was made of wooden planks instead of one solid slab of wood. You get the appearance of grooves without fussing with actual grooves, shifting boards, uneven gaps, and glue seepage. Check out the photos of the finished boards above or the one below after step 6 to see the “grooves.”
It’s important to have an understanding of wood when building DIY furniture projects. Not just how to cut, and assemble with wood but also to understand how it works. In Mistakes with Wood Can Cause Your DIY Furniture to Crack we talked about how wood is hygroscopic. Simply put, hygroscopic means it absorbs moisture from the air. Seasonal changes cause wood to absorb and release moisture.
Now that you have the final dimensions for the table top, you need to choose which boards you want to use.  Because we don't have a table saw and we wanted to keep this project simple and not cut any boards lengthwise, we {and by we, I mean my husband} plugged and chugged different board sizes into his calculator to find the perfect equation. We ended up using seven 1x6 boards for the width and on the two end caps we used 1x8's. Remember, a 1x6 is not six inches wide, it's five and a half, and a 1x8 is seven and a quarter inches wide. When you are doing your math to figure out what boards you need, remember that the nominal size {1x4, 1x6, 1x8, etc} is not the actual measured dimension of the board. 

Buying a pack of pre-organized furniture and project plans if you’re new to learning is beneficial for several reasons. Firstly, the packs of plans allow you to access a constant source of instructional content from wherever you are, whether you’re in your shop or want to browse for ideas. There are many plan sources out there and huge amounts of plans being produced and being posted online and in forums each day. By paying a small fee to take advantage of organized woodworking resources, it is easy to learn the best techniques faster and begin making projects you will use for a lifetime.
There are YouTube videos that show how to attach tabletops using both of these tried and true methods. If you don't have a router or a biscuit joiner to make the holes for the z-fasteners, you can always use a drill. For the figure-8's, you need to recess them so they're flush with the apron...so for that, you would need to use a router. If that's not somethig you can do, I suggest sticking with the Z-fasteners. Best of luck!

Using pocket holes to attach the stool base to the stool top prevents the top from moving during seasonal changes. It’s also not a good idea to drive screws through the edge of the apron into the table top. Over time the top could crack or the top could have enough force to push or pull the joints of the base apart. Skate over to Mistakes with Wood Can Cause Your DIY Furniture to Crack to see more about how I incorrectly attached the top on the stool.


I used a dry brush, barely dipped it in paint, and then lightly brushed it over the wood. If you get too much coverage with the paint, sandpaper is your best friend! You can stain the wood if you want a darker look peeking out from underneath. Check out the stain in this DIY post, it’s a great way to get that aged look quickly: http://www.jasonandshawnda.com/foodiebride/archives/11310
You would think that a sharp tool you swing in the direction of your ankles wouldn't last long. But the adze can be traced back at least to ancient Egypt. You use the adze to shape tree trunks and square them up into beams; looks like an ax with the blade oriented on the horizontal. But with modern-day milling capabilities so much faster and easier, for the most part the adze has gone the way of the dodo.
If you have some basic carpentry and tool usage skills, take advantage of Ryan's custom woodworking plans and the opportunity to build a custom entertainment center yourself with entertainment center plans, media center plans and woodworking plans designed and published by Ryan. If you don't, now is a great time to start. Its not as difficult as your may think.

Working on one side at a time, glue and nail the side to the back. Apply glue and drive three 1-5/8-in. nails into each shelf, attach the other side and nail those shelves into place to secure them. Clamps are helpful to hold the unit together while you’re driving nails. Center the top piece, leaving a 2-in. overhang on both sides, and glue and nail it into place. Paint or stain the unit and then drill pilot holes into the top face of each side of the unit and screw in the hooks to hold your ironing board. Mount the shelf on drywall using screw-in wall anchors.


Do you have older 18V DeWalt tools that are still near and dear to your heart but need new batteries? Consider firing up those old tools with 21st century technology. Now, 18V tools can be run on powerful 20V lithium Ion batteries with DeWalt’s new battery adapter. The adapter slides into the tool and the battery hooks onto the adapter. It works on most 18V DeWalt tools but not all. It’s sold two ways: the adapter alone (DCA1820), or the adapter with two compact 20V, 2.OAh batteries and charger. Now you’ll be able to hold on to your favorite cordless reciprocating saw forever!

​The plan tutorial includes images, diagrams, step-by-step instructions, and even a video to help you along the way. You can also go with some more bookcase design ideas. Browse the internet for more and we are also proving a link below to some more ideas to this plan. Select and build one of these free bookcase DIYs and you will have everything available easily that you need to get started creating a bookshelf for any room in your house.
Let’s start with perhaps the most basic tool in every household – the claw hammer. The claw on one side of the head should be well counterbalanced by the finished head, which should be somewhat rounded. The other kind of head is the waffle-head. Most commonly used in construction, it leaves a distinctive waffle mark on the wood when you drive the nail. This, of course, is not the proper nail for woodworking.
Adirondack Chairs in Tennessee Cedar Wood Growing up in Central New York and spending years in the Adirondack Mountains, I grew up seeing all types of Adirondack chairs. But it was not until I moved to middle Tennessee that I attempted to build Adirondack chairs myself. I found plans that gave me the basic design to build the adult chairs. I made some adjustments in order to fit them into my style and the type of wood that I have available. I found a cedar mill within an hour of my shop that allows me to purchase rough cut lumber. Because of the nature of rough lumber I am buying wood that is actually thicker, wider and longer than wood purchased at a brick front store.  Where a nominal 2”x 4”x 96” bought at a local lumber store is actually 1.5 x 3.5 x 96. The cedar I purchase is 2 ¼ x 4 ¼ x 102 inches. Once run through the surface planer to clean up the roughness and sanded, I am able to build with actual 2” x 4” or 2” x 6” lumber. This makes the chairs heavier, sturdier and more durable. Because of the size of the wood I assemble the legs and main supports with 3/8” carriage bolts. The arms, seat boards and backs are all assembled with 2” to 3” exterior screws. I predrill all the holes prior to inserting any screws. I do this because cedar, or any wood for that matter, can split at any time. The actual finished chair stands 38” tall x 39” long and 33” wide. They weigh about 35 lbs. and can seat a large adult very well but also comfortable for my tiny framed wife. The rise of the seat from the knees to the ground for your feet is 13 ½ inches. The seat reclines backward naturally but not so much that it is hard to stand from a seated position. The back is curved to support the natural curve of your back allowing for a more comfortable fit. The back is 32” tall to support even a taller person. The arms have been described as looking like whales so they are narrow where they fasten to the back of the chair and wide in the front for a cup, a book or even a laptop if you choose to work outside. *DISCLOSURE: Some of the links below are affiliate links. If you chose to click through and make a purchase I will earn a commission but there is no additional cost to you. It helps compensates the business for the time spent creating these posts. THANK YOU! Child’s Chair: The smaller child chairs are added to match the adult chairs to finish the family. These also are made with rough cedar milled and sanded to size to make the chairs sturdy. As with the adult chairs the wood will be thicker, wider and stronger than nominal wood. I use all true 1” lumber for the
×