Keep your woodworking tools and knives razor-sharp with our wide variety of sharpening supplies and accessories. We have what you need for jointer and planer knife sharpening. For sharpening plane irons and chisels, we supply a variety of diamond and waterstones, the Infinity Sandpaper Sharpening System, and honing guides. Our power sharpening systems include the Worksharp Knife Sharpeners, Ken Onion edition for the sharpest knives in the drawer.
You’ll need a long screwdriver with a square blade that is very heavy duty. This gives you a lot of torque. You’ll also need a small and medium slot screwdriver. For working on cabinets or tight places in woodworking, you’ll need a screwdriver with a thin shank so that you can reach screws that are inside of deep holes. This is accomplished with a cabinet screwdriver. Get a couple of medium Phillips head screwdrivers, and a stubby one too, for those tight places. You may also want a ratcheting screwdriver.
Do you have older 18V DeWalt tools that are still near and dear to your heart but need new batteries? Consider firing up those old tools with 21st century technology. Now, 18V tools can be run on powerful 20V lithium Ion batteries with DeWalt’s new battery adapter. The adapter slides into the tool and the battery hooks onto the adapter. It works on most 18V DeWalt tools but not all. It’s sold two ways: the adapter alone (DCA1820), or the adapter with two compact 20V, 2.OAh batteries and charger. Now you’ll be able to hold on to your favorite cordless reciprocating saw forever!
Turning over the sturdy tabletop, I felt a thrill of vindication. Clearly, it wasn’t a mistake in the end to use all three stains for the same project. Before I could consider the job done, though, I would need to apply sealer—Minwax Helmsman Spar Urethane—to protect the wood from moisture, UV rays, and the wear and tear of day-to-day life. This was my first time experimenting with a spray-application sealer, and I loved it. Obviously, it’s important to have proper ventilation in your work area, and you’ve got to shake the can vigorously before spraying, but so long as you remember the basics, spraying couldn’t be more straightforward. Holding the Helmsman Spar Urethane can about a foot from the surface, spray in a series of even strokes, always in the same direction, until you’ve completed the first coat. Let the sealer dry for about four hours before applying any additional coats, and for best results, sand the entire surface before each application of a new layer.
Up to now, I had been completely focused on the upward-facing portion of the tabletop, the side that would be most visible. But as I drew nearer to the finish line, I started to doubt my earlier decision not to finish the bottom side too. So I went back and did the extra work, and though this additional step might have been unnecessary, I like to think it helped make the table fit better into its home for the summer, my front porch. All that was left now was to attach the top to the metal table. As easy as it was to finish the tabletop with Minwax, it was no mean feat to devise a way of securing the top to the base. Ultimately, the answer to my problem came in an unlikely form. On a typical day, electrical cable hardware would never have entered my mind, but as the result of a funny twist of fate—the same sort of coincidence that led me to undertake this project in the first place—these simple snap-and-click fasteners enabled me to attach the top to the base and call it day. Now, with this project under my belt, I’m starting to eye those 2x6s still lingering in my scrap pile!

She has permanently glued and screwed the tabletop within that four-sided, mitered frame. Attaching the skirt to the long edges of the wide boards is no problem, but fastening them to the end grain of the wide boards, as shown in the photo above, is. The builder has constricted the wide boards' movement, and as they grow or shrink in width but are held in place by those end-caps, they will warp and split, making this a short-lived piece of furniture.
I've worn this apron in my studio/workshop several times now, and I really like it. It's more expensive than some, but the materials and construction are first-rate. I rarely give five stars, but the workmanship on this apron is impressive. The fabric is substantial and, although a bit stiff at present, comfortable to wear. The strap and grommet system is pretty clever, allowing a good fit for most, I would think. I'm a 5'-7" not-skinny woman, and I'm able to cross the straps at the small of my back and then tie them in front, so I'm guessing there would be plenty of strap length for bigger men. The straps sit comfortably on my shoulders. And all the pockets are great!

A few days back, I was searching for some cool DIY plans. So, I got to work and ended up coming up with some easy to follow project and an awesome new ice chest cooler to have out on the deck! It was going to be perfect for summer hangouts and barbecues. It was a fun and practical plan to work on and I know you will have fun tackling select a design from this plan and start building your own. Enjoy learning how you can build a rustic cooler also sing the video tutorial and source tutorial plan!


If you sand through the polyurethane and remove some stain, you can touch up with more stain. But the repair won’t be perfect, so take pains to avoid that mistake. Sand very lightly after the first coat, just enough to remove the dust whiskers. After the second coat, you can sand a little harder to flatten larger flaws. Always be careful around the edges of the table; that’s where it’s easiest to sand through.
Stanley produced this all-in-one layout tool between 1888 and the 1930s. It looks like a directional arrow from a street sign and was originally advertised as 10 tools in one (including level, depth gauge, try square, and compass). There are a few companies that make replicas, but originals can still be found on eBay for a couple hundred dollars apiece.
We have a small dining room area in our farmhouse that is separate from the living room and kitchen. The area is much smaller in space than our last house. I was little confused that our typical rectangular farmhouse table was not going to cut it. So, I walked in I came to know that we needed to build a round dining table. So, I searched for a plan design idea and build a very own round farmhouse dining table. I was an amazing DIY plan, I just love it!
Online plans can be easy, helpful, and can save you time and money if you put in the effort to usethem. But if you buy plans one by one, you might speed a lot of time organizing and searching for things to build as well as having to decipher different plan formats. You might learn a technique or two or improve your skills slightly, but you’ll forget everything by the time you go to find another plan. With organized lessons, however, you can always find the plans or instructions again easily, and come up with even more ideas of projects to build. Downloadable woodworking courses can save you money as well.
I’ve been toying with the idea of building a new table top. The legs of my dining table are hardwood. But the table top is not; it’s covered in veneer which is coming off in strips. I thought of removing the table top completely and utilizing the existing legs with a newly built hardwood top. But you’re solution seems easier! However, my tabletop is much thicker than yours, a 1 x 1 inch lip would not suffice. Can I just adjust the size of the lip, 1 x 2 inch? Or do I have to adjust the size of all boards used? Thanks!
Begin by cutting off a 10-in. length of the board and setting it aside. Rip the remaining 38-in. board to 6 in. wide and cut five evenly spaced saw kerfs 5/8 in. deep along one face. Crosscut the slotted board into four 9-in. pieces and glue them into a block, being careful not to slop glue into the saw kerfs (you can clean them out with a knife before the glue dries). Saw a 15-degree angle on one end and screw the plywood piece under the angled end of the block.
After all slots are cut, stand each board on end and coat the edge of jointed side with wood glue. Next coat the biscuits with glue. Insert biscuits in one side only of each board, then insert glued biscuits in the empty joint of the next board. Assemble planks in order until the top is complete. Don't worry about small gaps. Next, carefully lay the top down and attach pipe clamps at roughly 1' intervals. Slowly tighten each pipe clamp in a consistent fashion until the gaps disappear*. Small amounts of glue can be removed when dry; scrape up any puddled glue with a plastic putty knife. To minimize sanding later, avoid working glue into the top of the wood. Let the top set overnight.
Some moisture meters have pins that penetrate the surface of the wood. This can leave tiny holes that mar the surface and require filling. Others are pin-less. They have sensing plates that scan the wood beneath. However, not all pinless moisture meters are the same – look for one that uses technology that is not affected by the surface moisture in the wood, such as Wagner Meters IntelliSense™ Technology Moisture Meters.
Simply brilliant. Why didn’t I think of this? So we have a nearly 100 year old house. There is always something that needs repair. Thanks to whoever invented this little guy! No more mouth full of nails or screws. No more climbing up and down the ladder to get the damn screwdriver I dropped. Probably won’t hold your 16 oz claw hammer but other than that it is perfect. I love this. Highly recommend. Thanks for reading
This is a unique and cherished tool in my shop. 30 years ago my brother was a nuclear pipe welder at a federal submarine yard. He made this there and came home with it one day. The blade is submarine hull steel, Nickel Cobalt. I’ve never been able to sharpen it and it’s never really gotten dull. I had a diamond stone but quickly stopped using it as the diamond dust was being stripped off the stone. It has nostalgic and useful meaning to me.
Keep your woodworking tools and knives razor-sharp with our wide variety of sharpening supplies and accessories. We have what you need for jointer and planer knife sharpening. For sharpening plane irons and chisels, we supply a variety of diamond and waterstones, the Infinity Sandpaper Sharpening System, and honing guides. Our power sharpening systems include the Worksharp Knife Sharpeners, Ken Onion edition for the sharpest knives in the drawer.

Even a small tabletop presents a challenge if the boards you glued together  have stepped-shaped misalignments where they meet because of warping. Yes, you can sand these off, but the more topographical sanding you need to do, the less flat and regular your finished tabletop will be. The flatter and better aligned your boards are when they’re in the clamps, the happier you’ll be later. This is where end clamps and gluing cauls can help.


Most chisels are beveled on the 2 sides and on the cutting edge, but specialty chisels may only be beveled at the cutting edge. This bevel will be at 20 to 25 degrees down the length of the blade on one side, and flat on the backside. The blade will be between 4” and 7” long. Make sure you get chisels with a grip that fits your hand. If the grip is too small, you won’t be able to hold the chisel steady as you work. Be sure to use a mallet or wood hammer when you work, so that you don’t destroy the head on your chisel. Keep track of the edge caps, keep them sharp, and oil the metal now and then after you’ve used them, and they should be good for years. If you don’t have the edge caps, get a roll to keep them in. This will prevent them from bouncing around in your tool box drawers and getting damaged.

Diablo's 3 piece Adjustable Cabinet Router Bit Set Diablo's 3 piece Adjustable Cabinet Router Bit Set features a rail and stile bit set and a Double Shear raised panel bit. Featuring TiCo carbide with titanium these bits provide a long cutting life and ultra-fine finish. Perma-Shield Diablo's high performance coating reduces friction and build-up on the bits. The ...  More + Product Details Close 

A heavy-duty hardened steel chain with hexagonal links will thwart nearly every thief with a bolt cutter. Hexagonal links (or square or trapezoidal) make it impossible for bolt cutters to get a grip. You may be tempted to buy chain by the foot at the hardware store, but it’s designed for lifting and towing, not theft resistance. Even the thick stuff is likely to have round links, and frankly, if a hardware store clerk can cut the chain easily, a thief can too.
Woodworkers are a social bunch, and there are a few popular forums where people share thoughts on tools, discuss technique at length, and—of course—upload their plans. Some of the most active online woodworking communities include Lumberjocks, Woodworking Talk, Wood Magazine, WoodNet, Kreg, and Sawmill Creek. Search those to see if they have what you’re looking for (either with their built-in search tool or with Google’s site-specific search, e.g. site:lumberjocks.com side table).
Online packages also allow you to build at a convenient pace, whether you want to build one bench per week or want to try every new furniture plan available – and more importantly, the use of clear instructions will enable you to build under a comfortable environment without any pressure. That way, you do not face disappointment that you would otherwise experience if you buy hard-to-understand furniture plans or can’t find the specific project that you’re looking for. If you think that a plan outline is simple, you can find a more difficult one and begin practicing new skills and techniques. That way, you are able to build more things faster than if you bought each plan individually and had to search for it each time.
Everybody has a home remedy for sealing partially used tubes of caulk. But what if you had a single product that could seal caulk cartridges, squeeze tubes, glue bottles, felt-tip pens and anything else that has a nozzle? Well, these Little Red Nozzle Caps are just the ticket. Roll the cap down the nozzle to seal out dirt and preserve the remainder of the bottle, tube or cartridge.
Personally identifying information is information that can be used to identify who you are such as: name, mailing address, email address. To enter certain areas of the site, you will be required to register and provide information about yourself. This information is for the purposes of Canadian Woodworking and helps us to tailor the site to best meet the needs of our audience. 
The owners, webmasters, administrators, authors and editors, expressly disclaim all and any liability to any person, whether a user of this website or not, in respect of anything and of the consequences of anything done or omitted to be done by any such person in reliance, whether whole or partial, upon the whole or any part of the contents of this website. Please exercise caution when working with any tools or machinery. Follow common safety rules and precautions as outlined in any manuals related to the equipment being used. If advice or other expert assistance is required, the services of a competent professional person should be sought.

Do you want to use an oil stain, a gel stain, a water-based stain or a lacquer stain? What about color? Our ebook tells you what you really need to know about the chemistry behind each wood stain, and what to expect when you brush, wipe or spray it on. It’s a lot simpler than you think! This is the comprehensive guide to all the varieties of stain you will find at the store and how to use them.
This super-strong and simple-to-build workbench is may be the project you've been looking for a long time. You have to select some free workbench plans to create yourself a working table in your shed that after you can use it when you are working on your projects and maybe it can provide you some extra storage, depends upon which plan you are choosing to DIY.

Carefully lay the top down and attach pipe clamps at roughly 1' intervals. Slowly tighten each pipe clamp in a consistent fashion until the gaps disappear. Small amounts of glue can be removed when dry; scrape up any puddled glue with a plastic putty knife. To minimize sanding later, avoid working glue into the top of the wood. Let the top set overnight.
×