A super simple iPad Dock/stand made out of a single block of wood features an angled groove which gets to support the tablet device and a cut in a hole to revise access to the home button of your iPad. It’s possible to drill an access channel in the stand through which you can run a charging cable, although this mini stripped back iPad stand may have very limited functions.
A lot of woodworkers share their projects through their own blogs or YouTube channels. In fact, we’ve shared many of them here before, including, Woodworking for Mere Mortals, The Wood Whisperer, Matthias Wandel, April Wilkerson, Sawdust Girl, House of Wood, FixThisBuildThat, Pneumatic Addict, Build-Basic, Rogue Engineer, Her Tool Belt, and Ana White. The best YouTube woodworkers create great videos, but also provide a complete blog post with a cut list, tools, materials, and instructions. Find your favorites and save them for when you’re doing your searches.
With a pencil and a protractor, divide the larger disc into 30-degree wedges to create 12 center lines for the bottle indents. Center and trace the smaller disc on top of the larger disc. Next, with a drill press, drill 3/8-in.-deep holes on the 12 center lines with the 1-7/8-in. Forstner bit, spacing them between the disc’s outer edge and the traced circle. Next, divide the smaller disc into 60-degree wedges and drill six more 3/8-in.-deep holes with the Forstner bit.
The next hand tool every woodworker should have is a nail set. In fact, you should have several sizes. They look like awls, and you use them to drive nail heads into the wood so they are flush or right below the surface. This allows you to fill the holes and prepare for staining or painting. The nail setter will usually have either a convex or concave surface to grip the nail better and keep it from sliding off and marring the wood.
Let’s start with perhaps the most basic tool in every household – the claw hammer. The claw on one side of the head should be well counterbalanced by the finished head, which should be somewhat rounded. The other kind of head is the waffle-head. Most commonly used in construction, it leaves a distinctive waffle mark on the wood when you drive the nail. This, of course, is not the proper nail for woodworking.

Okay, let’s stain this beast. I should explain that we used Rustoleum’s Dark Walnut Ultimate Wood Stain, but we did it wrong. We failed to mix it well before applying it, resulting in a color we really liked–but not the color this stain is designed to create. When we came back to do a second coat, we stirred it well, resulting in a coat that looked like purple paint. I had to sand it off and start over. So, don’t follow my lead here–follow the can’s directions and TEST before staining all of your new masterpiece!
Drill four 5/8-in.-dia. 1/2-in.-deep holes on the large disc?inside the traced circle?then use 5/8-in. dowel centers to transfer the hole locations to the underside of the small disc. Drill four 1/2-in.-deep holes on the underside of the small disc and a 1/2-in.-deep hole in the center of the top for the dowel handle. Glue in the dowels to join the discs, and glue in the handle. We drilled a wood ball for a handle knob, but a screw-on ceramic knob also provides a comfortable, attractive grip.
I am so glad to see this. It is exactly what I have been looking for. I have had a similar idea in my head for years but didn't know how to bring it together, and I wasn't sure how it would actually turn out. Yours is beautiful. It is nice to start with an idea of how the project will actually look when I am done. My table is 25 years old with a laminate top. The reason I want to cover instead of replacing it does that it is the first purchase my husband and I made together. It has seen 25 years of abuse by three little (now big!) boys and by me, the messy crafter. But I cannot imagine ever getting rid of this table. Plus it's not like I'm going to get less messy, so investing in an expensive table would be crazy. I love how I can take this top off and still do the messy damaging things on it. I am bookmarking this and if I ever get around to actually doing it LOL, I will send you pics
Probably the handiest shop accessory in this list would be the woodworker's bench, complete with a vise. The bench is a stable-based table with a thick, hardwood top. In the top are a series of holes that are designed to accommodate bench dogs, which are little more than pegs that can be moved from hole to hole as necessary. The end of the bench has the aforementioned vise that works in concert with the bench dogs to hold pieces steady for the woodworker.
With a collection of workshop tools--whether for construction jobs or for around the DIY house projects--it’s top priority to make sure all of your tools are in the best shape and are taken care of. Tools don’t come at a cheap price, so proper care is essential in order for them to last for a long time. Unfortunately, after much usage, wear, tear, and rusting of tools tend to happen. Luckily, at Bora Tools, we sell a vast variety of workshop accessories that are specific to cleaning and restoring needs. From waxes, polishes, rust removers, to covers, racks, and more, we have an abundance of products that are designed to keep your high-quality, expensive tools in prime condition all year round.
Yes Seriously! You can build an easy bed frame yourself without any other’s help. As everyone knows the starting point of any bedroom is a gorgeous bed. However, you also need something that lets you enjoy peaceful slumber in comfort and warmth, but since the bed took as the focal point of the room, you may need something that looks really good too.
For starters, this DIY wood table is for my son to keep his Lego projects and erector set buildings on. Secretly, it’s for me because, in turn, it will keep the Legos from being scattered all over my house. We decided on measurements of 60″ long x 18″ deep for the table top. Now that I know how big I want our homemade table to be I reached out to Osborne Wood Products to find out what the next step is for building a table. They were super helpful and made it very easy to order the table base kit. We let them know the measurements for the table top as well as how much of an overhang. We then choose the traditional dining table legs in soft maple along with a 4″ wood skirt also in soft maple. The furniture kit came well packaged and rather quickly. 

You would think that a sharp tool you swing in the direction of your ankles wouldn't last long. But the adze can be traced back at least to ancient Egypt. You use the adze to shape tree trunks and square them up into beams; looks like an ax with the blade oriented on the horizontal. But with modern-day milling capabilities so much faster and easier, for the most part the adze has gone the way of the dodo.
There are lots of clear finishes. But for a combination of usability and durability, you can’t beat polyurethane. Oil-based poly, which dries slower than water-based, is best for beginners because it allows more working time. The other important difference is clarity: Water-based poly is absolutely colorless, while oil-based has an amber tone, which can be good or bad depending on the look you want.
OK, the Long Ranger’s been around since Marconi. But we love it. Simply put, this Long Ranger III Remote Dust Collector Switch is a remote system for turning on your dust collector out in the shop from whatever tool you’re operating. It plugs into the wall, you plug your dust collector into that and you’re done. Push the button on your remote and it fires right up. It’s saved us about two years and 1,300 miles of walking back and forth to the dust collector switch.
Personally identifying information is information that can be used to identify who you are such as: name, mailing address, email address. To enter certain areas of the site, you will be required to register and provide information about yourself. This information is for the purposes of Canadian Woodworking and helps us to tailor the site to best meet the needs of our audience. 
This is a unique and cherished tool in my shop. 30 years ago my brother was a nuclear pipe welder at a federal submarine yard. He made this there and came home with it one day. The blade is submarine hull steel, Nickel Cobalt. I’ve never been able to sharpen it and it’s never really gotten dull. I had a diamond stone but quickly stopped using it as the diamond dust was being stripped off the stone. It has nostalgic and useful meaning to me.
Using pocket holes to attach the stool base to the stool top prevents the top from moving during seasonal changes. It’s also not a good idea to drive screws through the edge of the apron into the table top. Over time the top could crack or the top could have enough force to push or pull the joints of the base apart. Skate over to Mistakes with Wood Can Cause Your DIY Furniture to Crack to see more about how I incorrectly attached the top on the stool.
When it comes to choosing a finish there are two main choices. The typical approach of stain and urethane creates a smooth, wipeable surface, but when that finish eventually wears through, there’s no way of repairing it attractively. Sanding back to bare wood and refinishing is the only way to make it respectable again. Oil and wax finishes, on the other hand, take more time to apply initially, but they’re easily repaired and rejuvenated with the tabletop in place. Regular reapplication works just fine.
The most common paper writing service which the majority of our customers require is essay writing. If you have always experienced difficulties with this type of assignment or could not find relevant data to provide solid arguments, our experts are at your service. We will assist you with any type of essay you have and write an excellent paper which will bring you a high grade.
Open rafters and trusses are an endless source of falling dust. So if you’re working under an open ceiling, hang plastic sheeting above. Keep the plastic at least 12 in. from light fixtures or remove the bulbs. Sometimes, adding plastic ‘walls’ is a lot easier than cleaning up the entire area. If you’re using oil-based finishes, hang the sheets about a foot from the floor to allow for ventilation.
When it comes to choosing a finish there are two main choices. The typical approach of stain and urethane creates a smooth, wipeable surface, but when that finish eventually wears through, there’s no way of repairing it attractively. Sanding back to bare wood and refinishing is the only way to make it respectable again. Oil and wax finishes, on the other hand, take more time to apply initially, but they’re easily repaired and rejuvenated with the tabletop in place. Regular reapplication works just fine.

Manufacturers that produce woodworking tools and materials have got into the content creation game, too, and some will share woodworking plans online. Minwax and Ryobi, for example, provides their plans free of charge, and Rockler offers their woodworking plans for a fee. Seek them out along with the other blogs and you’ll have a handy list of resources you can turn to for any project.
We call them strongbacks and we use them on every tabletop we build. It's just a scrap strip of 3/4" plywood, with 3/4" pocket holes drilled about ever few inches. The strongback is attached to the bottom of the tabletop as the glue dries. The square edge of the plywood prevents the tabletop from warping or cupping as it dries. Then we remove the strongbacks (and save them for the next tabletop) when we attach the tabletop to the base.

In an effort to replace the table, I started looking at garage sales and on craigslist for replacements. I was coming up empty handy {they all looked worse than ours!} or being totally priced out.  I started to think, why not just use the table that we have and slap a few boards on it.  My engineer husbands thinking is a little more refined than "slapping" boards on something, so he came up with an idea {and like a true engineer made an auto cad design}, we tweaked it a bit together and then took a little date to Home Depot. Because that my friends, is where adults go on dates.
It’s important to have an understanding of wood when building DIY furniture projects. Not just how to cut, and assemble with wood but also to understand how it works. In Mistakes with Wood Can Cause Your DIY Furniture to Crack we talked about how wood is hygroscopic. Simply put, hygroscopic means it absorbs moisture from the air. Seasonal changes cause wood to absorb and release moisture.

The end grain of wood soaks up finishes and often turns much darker than the face grain. Check for this on your test block. If you get an ugly result, pretreat the end grain with a dose of finish that will limit absorption (wood conditioner, sanding sealer, shellac or polyurethane thinned 50 percent). Apply the treatment with an artist’s brush and be careful not to slop onto the face grain.


Holy Craft came up with a genius solution for a scratched and worn dining table!  If your table looks a little worse for wear, but you still plan on using it for messy situations like painting and crafting, you’ll love this wood plank tabletop cover.  Slide it on for nice dinners and entertaining company, and tuck it away when your kids use play dough! // Holy Craft on Remodelaholic

There was a big crowd, rocking music, and a lot of excitement over the Extreme Post-it Notes at the 3M booth at the 2018 International Builders Show. Apparently these things stick to wood, hot stuff, cold stuff, wet stuff, brick, metal, plastic pipes, ladders, stair treads, flooring, the side of a truck, copper, tools, siding, co-workers, concrete, tile, drywall, asphalt, house wrap, light fixtures, switches, cabinets, leather belts, windows…well, you get the idea. Post-it Extreme Notes will be available at major retailers beginning in March 2018.
The most commonly purchased claw hammer is the 20 oz. size. It’s heavy enough to easily drive nails but easily manipulated when pulling nails. While wooden handles are picturesque, they may not stand up to the strain if you have to pull a lot of nails. Hammers with a steel handle, or even fiberglass, will be stronger. However, these won’t absorb the vibrations from driving nails the way a hickory handle will. You’ll also need to make sure the fiberglass and metal handles have a rubberized grip for control and comfort. If you’re going to be driving a lot of nails, the wooden handled hammer will be better for reducing stress on your hand, and wrist, too.
There are lots of clear finishes. But for a combination of usability and durability, you can’t beat polyurethane. Oil-based poly, which dries slower than water-based, is best for beginners because it allows more working time. The other important difference is clarity: Water-based poly is absolutely colorless, while oil-based has an amber tone, which can be good or bad depending on the look you want.

It’s important to have an understanding of wood when building DIY furniture projects. Not just how to cut, and assemble with wood but also to understand how it works. In Mistakes with Wood Can Cause Your DIY Furniture to Crack we talked about how wood is hygroscopic. Simply put, hygroscopic means it absorbs moisture from the air. Seasonal changes cause wood to absorb and release moisture.


A piece of 1/2” plywood offers the best approach for determining the optimal size and shape of your tabletop because it lets you test and tweak various options in 3D. Cut the plywood to the maximum size you might want, set it up on something in the place where the finished table will go, then live with it for a while. Should the top be narrower? Shorter? Now’s the time to find out. Saw some off your plywood mock-up if need be, then live with the new size until you’ve found the sweet spot.
Clean wooden gutters of any loose debris and cut to a manageable length. Miter down to form an approximately 40" x 94" rectangle. Coat the corners with wood glue and fasten together with 15-gauge finish nails. If miters are tight 45-degree cuts, box should be square. Double check diagonal measurements before fastening completely. The two diagonal measurements should be as close to equal as possible.
Hey Great Article,Thanks. 4 months ago, I started looking for woodworking.The industry is extremely interesting,but I have problems with how I can do it.My uncle who has been doing more than me in this industry,has suggested to me to follow Teds plans.Do you think it’s a good move to follow these plans??I keep reading good reviews about Teds plans but I am unsure if it will still work on me.At this time I can purchase these plans at a very low price,so if possible can you leave me feedback on wether I should do it or not. It would mean a lot coming from an expert in this field.
Begin by cutting off a 10-in. length of the board and setting it aside. Rip the remaining 38-in. board to 6 in. wide and cut five evenly spaced saw kerfs 5/8 in. deep along one face. Crosscut the slotted board into four 9-in. pieces and glue them into a block, being careful not to slop glue into the saw kerfs (you can clean them out with a knife before the glue dries). Saw a 15-degree angle on one end and screw the plywood piece under the angled end of the block.
×