You can also use Google image search to research a project. Unlike the PDF search, the image search provides a photo of what the project will look like, which is helpful in determining if you want to pursue building it. By doing an image search for how to build a step stool, you will have a ton of options that all lead to woodworking plans of various quality. (The how to part of these is important—otherwise you’ll just get pictures of step stools.)
This is another wood table but this time with a more elaborate design. Instead of using a large log, this time you’ll need several small ones. The idea is to cut them to the same height and to try to create a mosaic with them. You can glue them together and you can also wrap a piece of rope or something similar around them. You should be able to create an original coffee table.
This continuous absorption and releasing of moisture causes the wood to swell and shrink. This swelling and shrinking causes the wood to move and this movement causes issues. When it’s more humid, the moisture in the air is absorbed and the wood swells. The swelling actually has enough force to push and pull joints apart. Worse yet, if the wood is joined incorrectly it can cause the wood to crack and split.
Reclaimed Wood from Corn Crib HOW TO DESIGN AND BUILD AN ENTRY WAY COAT RACK AND BENCH There was a door in granddad’s home the client wanted to preserve and wondered, if they provided the wood, could I build an entryway coat rack and bench using the door as part of the build. The wood they wanted to provide, well, that was from the family owned Tennessee corn crib that had been torn down and they didn’t want to lose the wood or the memories. Not only was this a corncrib but it was eventually used by the great grandchildren as a play house. So for the client there are as many memories in this build as there are colors. THIS PROJECT TRULY DEFINES THE “CUSTOM” in BAYNE CUSTOM WOODWORKING. I spent some time to design a simple layout in @sketchup_official so the client could approve the idea I had in mind. The wood showed up in two deliveries so we stacked it outside because this was the first time I worked with barn wood. I did not want to introduce possible termites to my shop. So my first call was to my pest guy asking how I would treat the wood for termites. Much to my relief he said I had nothing to worry about. This was “real” wood! Not nominal at all, nominal is how we buy our wood at a local hardware store. Where a 2×4 is actually 1 ½  x 3 ½ . These 2×4’s were at least 2”x4”’s if not more and were hard, heavy and dusty, did I say heavy? After cutting to length on my handy @DewaltTough miter saw, I had to take them to my @ridgidpowertools table saw and square up the bottoms only.  I was very careful not to lose any of the original saw marks and character because that would ruin the entire purpose. For someone who likes clean, crisp edges, this was a bit of a challenge. I used @kregjig Kreg Jig® K4 Master System to join all the pieces of the base, the seat frame and the supports to join the two together. I was very careful to hide all of the pocket holes so they could not be seen from any angle. I used Titebond Products original interior wood glue to join all the pieces together. The next item was to assemble the back which included grandad’s door as the center piece. The door was only 71 ½ tall which determined the overall height of the project. Part of this back also includes two live edge pieces that we picked to use as the “L” shaped wings or side walls. The door measured 24” which left me with 6” on each side to make up the final size of 36”. So I chose two of the straightest boards that were closest to 6” and cut them to width so as not to waste any wood or lose any character. I used the Kreg Jig® K4 Master System
Even a small tabletop presents a challenge if the boards you glued together  have stepped-shaped misalignments where they meet because of warping. Yes, you can sand these off, but the more topographical sanding you need to do, the less flat and regular your finished tabletop will be. The flatter and better aligned your boards are when they’re in the clamps, the happier you’ll be later. This is where end clamps and gluing cauls can help.
Cut the 6-1/2-in. x 3-in. lid from the leftover board, and slice the remaining piece into 1/4-in.-thick pieces for the sides and end of the box. Glue them around the plywood floor. Cut a rabbet on three sides of the lid so it fits snugly on the box and drill a 5/8-in. hole for a finger pull. Then just add a finish and you’ve got a beautiful, useful gift. If you don’t have time to make a gift this year, consider offering to do something for the person. You could offer to sharpen their knives! Here’s how.
DeWalt just introduced a new lightweight level. Interesting…but for folks accustomed to lugging around sheets of 9-ft. plywood and 80-lb. bags of mortar, aluminum levels aren’t really all that heavy. But the carbon fiber composite that makes this new level light is the same reason that it’s tough enough to spring back from impacts that would permanently throw an aluminum level out of whack. The DWHT43134 level is also mar-resistant, partially because of the design, partially because it’s 35% lighter than its aluminum counterpart.
This time I surprised one of my favorite dice games and took it outside. I made a set of wooden dice in just a few hours, and instead of sitting in the room and doing nothing, we are taking our dice game out into the yard. With this set of wooden dice, dice games are becoming our favorite backyard game. Check out the step by step tutorial below so you can make your own.
No sadly, as I mentioned above, my table top ended up splitting, starting at a knot on the edge and going clear across the top (pre-drill those holes!!!), so I had to come up with another solution.  I didn’t want to go to the trouble of making another table top like this one, so I did a much easier and quicker solution…stain-grade plywood with decorative moulding attached to the edges. 

This is another very interesting project. To make a similar table you need to have textured spray paint, matte black spray paint, lumber, wood boards, wheels, stain, sand paper, corner pieces, nails, bolts, nuts, washers, clamps and L brackets. First make the measurements and spray paint all the hardware including the wheels. Then make the basic box and sue nails to hold the wood pieces in place. Then use L brackets to keep them sturdy and add the bolts. Tighten the nuts into the bolts and attach the wheels.Then add the corner pieces sing nails{found on theblissfulbeeblog}. 

She has permanently glued and screwed the tabletop within that four-sided, mitered frame. Attaching the skirt to the long edges of the wide boards is no problem, but fastening them to the end grain of the wide boards, as shown in the photo above, is. The builder has constricted the wide boards' movement, and as they grow or shrink in width but are held in place by those end-caps, they will warp and split, making this a short-lived piece of furniture.

You can also use Google image search to research a project. Unlike the PDF search, the image search provides a photo of what the project will look like, which is helpful in determining if you want to pursue building it. By doing an image search for how to build a step stool, you will have a ton of options that all lead to woodworking plans of various quality. (The how to part of these is important—otherwise you’ll just get pictures of step stools.)
Add the ultimate in convenience, power, and safety to your router lift! JessEm's new soft-start, 3.25hp router motor puts the variable speed control and power switch at your fingertips. The control panel attaches directly to INCRA Router Table Stands and is easily adapted to other router table installations. Compatible with router lifts designed to accept the Porter Cable 7518 motor. This router is not for hand held use.
In an effort to replace the table, I started looking at garage sales and on craigslist for replacements. I was coming up empty handy {they all looked worse than ours!} or being totally priced out.  I started to think, why not just use the table that we have and slap a few boards on it.  My engineer husbands thinking is a little more refined than "slapping" boards on something, so he came up with an idea {and like a true engineer made an auto cad design}, we tweaked it a bit together and then took a little date to Home Depot. Because that my friends, is where adults go on dates.
Some tools that are required for this project are Miter saw, drilling machine, pencil, tape measure, screws, etc. Those, who prefer a video tutorial instead, can visit the below link to a YouTube video tutorial that illustrates the process of creating a DIY Beer Bottle Crate. The video tutorial explains every step properly so that anyone can make a Beer bottle crate easily.
Buying a pack of pre-organized furniture and project plans if you’re new to learning is beneficial for several reasons. Firstly, the packs of plans allow you to access a constant source of instructional content from wherever you are, whether you’re in your shop or want to browse for ideas. There are many plan sources out there and huge amounts of plans being produced and being posted online and in forums each day. By paying a small fee to take advantage of organized woodworking resources, it is easy to learn the best techniques faster and begin making projects you will use for a lifetime.
Breaking down heavy sheet-goods on a jobsite table saw is difficult, and dang near impossible when working alone. That’s where a track saw comes in handy. A good quality track saw can produce cabinet saw results out on any job. Now, this portable tool is even more portable. The FESTOOL TSC 55 is a cordless saw that has the same features and performs just as well as FESTOOL’s corded saw, including the cut capacity and blade speed. It also has a collection bag that actually works, collecting up to 90% of the dust. The batteries are compatible with other FESTOOL products and the saw runs on their standard tracks.
Are you redecorating your home but can’t seem to find the right table to complete your décor? Don’t worry too much because there are plenty of alternatives. There’s always a DIY project that can help you out. For example, we just found these beautiful DIY tables and we’re sure there are plenty more where these came from. Let’s take a look at them and see them closely.
Drill four 5/8-in.-dia. 1/2-in.-deep holes on the large disc?inside the traced circle?then use 5/8-in. dowel centers to transfer the hole locations to the underside of the small disc. Drill four 1/2-in.-deep holes on the underside of the small disc and a 1/2-in.-deep hole in the center of the top for the dowel handle. Glue in the dowels to join the discs, and glue in the handle. We drilled a wood ball for a handle knob, but a screw-on ceramic knob also provides a comfortable, attractive grip.

The owners, webmasters, administrators, authors and editors, expressly disclaim all and any liability to any person, whether a user of this website or not, in respect of anything and of the consequences of anything done or omitted to be done by any such person in reliance, whether whole or partial, upon the whole or any part of the contents of this website. Please exercise caution when working with any tools or machinery. Follow common safety rules and precautions as outlined in any manuals related to the equipment being used. If advice or other expert assistance is required, the services of a competent professional person should be sought.
For an artisanal look, you can use woodworking hand tools. These are easy to use, lightweight and require no batteries or power cords to operate. Many hand tools are covered by multi-year or even lifetime warranties for extra protection and value. Set up your pieces with the most expertly crafted woodworking hardware, such as hinges, pulls and knobs to create a final product that you can give as a gift, sell or just display proudly.
A dispensing gun allows you to save foam if the job requires less than a full can. Once the job is finished, just set the gun aside until the next time you need it. Leave the can on the gun if you know it will be used in less than 30 days, or pull the can off, cap it and then clean out the gun with cleaning solution. Besides saving you money on foam, the dispensing gun provides much greater control because you’re not working with a flimsy straw, and the trigger can be adjusted with a turning setscrew to control the rate of flow—nice! Spray foam dispensing guns are available online and at home centers.
×