A review of the Dewalt dwp615 The Problem Using a router inside the shop makes for a dusty shop. In the past when using my hand held trim or plunge router I would roll the projects out of the shop to avoid the mess. While this is fine in good weather, when it gets cold or rains it’s not an option so I use the tool inside and clean up the mess afterwards. The Solution I located a dust collection for my Dewalt dwp611 trim router and the dnp612 plunge base unit on Amazon and purchased the dnp615 and the dnp616. See my YouTube channel for the actual test and review. I tested them both with cedar because it is a wood that makes the most dust in my shop. Installation was easier than expected and fit into both bases. Using the trim base I was able to use the round over bit without any issues to achieve a clean cut and eliminate 85-90% of the dust. I did find the unit attached to the plunge base would not allow round over bits to extend deep enough to make a good cut, but with a straight bit it works great. Both Amazon links are available are below I would say this is a successful purchase and has eliminated the majority of the dust put out by the router. *DISCLOSURE: Some of the links below are affiliate links. If you chose to click through and make a purchase I will earn a commission but there is no additional cost to you. It helps compensates the business for the time spent creating these posts. THANK YOU!    
Relax and enjoy your outdoor space with this smart patio combo consisting of a sofa and chair. You can adjust the size completely to make it fit perfectly onto your patio or deck, and both the sofa and chair have arms that double as trays for al fresco dining. And you can make your own cushions to fit, or use shop-bought ones and add your own ties, if necessary.

To save money, we keep the temp in our shop down low when we’re not in it and crank up the heat when we return. But even when the air temperature hits 70 degrees F, the concrete floor is still Minnesota-cold. We tried a space heater under the bench, but it broiled the shins and still left us with cold feet. So we recently bought a foot-warming mat, and now our feet stay toasty warm. Plus, it uses a fraction of the electricity and is a lot safer than a space heater. The mat is produced by Cozy Products. The good folks over at Cozy suggest putting a chunk of cardboard underneath it if you use it on flooring that could fade from the heat, like carpet or wood. 

A lot of woodworkers share their projects through their own blogs or YouTube channels. In fact, we’ve shared many of them here before, including, Woodworking for Mere Mortals, The Wood Whisperer, Matthias Wandel, April Wilkerson, Sawdust Girl, House of Wood, FixThisBuildThat, Pneumatic Addict, Build-Basic, Rogue Engineer, Her Tool Belt, and Ana White. The best YouTube woodworkers create great videos, but also provide a complete blog post with a cut list, tools, materials, and instructions. Find your favorites and save them for when you’re doing your searches.
In an effort to replace the table, I started looking at garage sales and on craigslist for replacements. I was coming up empty handy {they all looked worse than ours!} or being totally priced out.  I started to think, why not just use the table that we have and slap a few boards on it.  My engineer husbands thinking is a little more refined than "slapping" boards on something, so he came up with an idea {and like a true engineer made an auto cad design}, we tweaked it a bit together and then took a little date to Home Depot. Because that my friends, is where adults go on dates.
Every student requires help with homework from time to time. Somebody works part-time and doesn’t have enough time to do all the assignments. Others are not good writing essays and always experience difficulties when they have to complete one more paper. Sometimes, even the best students become too exhausted and don’t have enough energy to write a quality paper. In such moments everybody needs a little help, and Homeworkfor.me is always ready to lend a hand with any academic problem.
ClickBank is the retailer of products on this site. CLICKBANK® is a registered trademark of Click Sales, Inc., a Delaware corporation located at 917 S. Lusk Street, Suite 200, Boise Idaho, 83706, USA and used by permission. ClickBank's role as retailer does not constitute an endorsement, approval or review of these products or any claim, statement or opinion used in promotion of these products.
OK, the Long Ranger’s been around since Marconi. But we love it. Simply put, this Long Ranger III Remote Dust Collector Switch is a remote system for turning on your dust collector out in the shop from whatever tool you’re operating. It plugs into the wall, you plug your dust collector into that and you’re done. Push the button on your remote and it fires right up. It’s saved us about two years and 1,300 miles of walking back and forth to the dust collector switch.
We no longer have that problem because we picked up a set of Mag Shims from FastCap. Mag Shims are 1/8-in. magnetic spacers. If you need a blade height of 7/8 in., simply stack seven spacers, and raise the blade to match. They also work great for setting the depth on router bits and drill presses. We stick them right to the backside of the fence, so they’re always at hand and never get lost.
artistic awls business commercial cutting design equipment featured fitting fixed base furniture hammers home improvement income jigs knives moving base non-commerical online patterns pieces plan plans portfolio preparing products professional project projects router saws sketching skilled skills squares supplies table saws tabletops tapes tools website wood woodworking Woodworking Projects For Beginners
We call them strongbacks and we use them on every tabletop we build. It's just a scrap strip of 3/4" plywood, with 3/4" pocket holes drilled about ever few inches. The strongback is attached to the bottom of the tabletop as the glue dries. The square edge of the plywood prevents the tabletop from warping or cupping as it dries. Then we remove the strongbacks (and save them for the next tabletop) when we attach the tabletop to the base.
PROCESSING NOTES: No matter how easy I have tried to make following these media center plans and constructing them, if you find it overwhelming to attempt the project or operate the basic tools necessary for completion, get help. Contact your local supplier to see if sheet goods can be ripped to fit your car trunk. The possibility of ordering all the parts ready for assembly is also available. Most importantly, when you set off to build your project, help is only an email message away.
After you've used one of these free coffee table plans to build your dream coffee table, check out these other free woodworking plans for bookcases, TV stands, dressers, nightstands, step stools, entertainment centers, farmhouse tables, desks, jewelry boxes, dining room tables, wine racks, picnic tables, kitchen islands, home bars, bunk beds, toy boxes, and even dog houses.
With a collection of workshop tools--whether for construction jobs or for around the DIY house projects--it’s top priority to make sure all of your tools are in the best shape and are taken care of. Tools don’t come at a cheap price, so proper care is essential in order for them to last for a long time. Unfortunately, after much usage, wear, tear, and rusting of tools tend to happen. Luckily, at Bora Tools, we sell a vast variety of workshop accessories that are specific to cleaning and restoring needs. From waxes, polishes, rust removers, to covers, racks, and more, we have an abundance of products that are designed to keep your high-quality, expensive tools in prime condition all year round.
And if you haven’t got a fancy stencil hanging around, you can still give your table a stencil-styled makeover, and it won’t take much.  To make this fun herringbone table, Shark Tails took a boring side table and taped off a herringbone design then spray painted it gold!  It adds a touch of mod glam that’s not overwhelming since it’s in a small dose. // Shark Tails
Every student requires help with homework from time to time. Somebody works part-time and doesn’t have enough time to do all the assignments. Others are not good writing essays and always experience difficulties when they have to complete one more paper. Sometimes, even the best students become too exhausted and don’t have enough energy to write a quality paper. In such moments everybody needs a little help, and Homeworkfor.me is always ready to lend a hand with any academic problem.
I started by doing some searches around the ol’ internet to find other folks who’ve built their own tables. Using the images and information I found, I started drawing up plans. My table is approximately 6’x44″x31″ (LxWxH). You may find different dimensions work better for you (31″ is pretty tall)–so make your plans however you like. I also built leaves that make the table 8.5’ long.
As your interest in woodworking grows, you’ll want to subscribe to a woodworking magazine. This will help feed your new found obsession with articles on tools, techniques, and woodworking plans. As a print magazine subscriber you’ll also gain access to their database of plans on their websites. Popular magazines include, Woodworkers Journal, Fine Woodworking, and Popular Woodworking.
No, it’s not a blood pressure tester. It’s an inflatable shim sold by Calculated industries. What in the world would you do with an Air Shim? Well, you could hold a window in position (by yourself) while setting the permanent shims, or prop up a door slab during installation without scratching the hardwood floor. Use it to align base cabinets or level appliances. You could even trick your big, burly buddy by betting him that your 10-year-old can pick him up off the ground… you will win that bet because the Air Shim is easy enough for anyone to pump and it holds up to 300-lbs. Deflate it as slow as you want for uber precision adjustments.
My son asked for his DIY table to be painted green. But I can’t see myself making a wooden table and then painting the whole thing bright green. Sorry buddy, but it will still be great and green with painted layers. Thankfully, Dixie Belle has an amazing selection of colors! I will be painting the table using all of these gorgeous greens. The greens are:
Online packages also allow you to build at a convenient pace, whether you want to build one bench per week or want to try every new furniture plan available – and more importantly, the use of clear instructions will enable you to build under a comfortable environment without any pressure. That way, you do not face disappointment that you would otherwise experience if you buy hard-to-understand furniture plans or can’t find the specific project that you’re looking for. If you think that a plan outline is simple, you can find a more difficult one and begin practicing new skills and techniques. That way, you are able to build more things faster than if you bought each plan individually and had to search for it each time.
Well I certainly can say most times when anyone comes into my shop they always ask….what’s this do?...lol Although not my own design I do get many questions on the German Springpole Lathe from Roys last book. It’s always a fascinating conversation piece…and usually gets people that have never worked wood really interested and wanting to learn more. When I show them spindels and how it works I always get an impressed or entertained reaction.
There are lots of clear finishes. But for a combination of usability and durability, you can’t beat polyurethane. Oil-based poly, which dries slower than water-based, is best for beginners because it allows more working time. The other important difference is clarity: Water-based poly is absolutely colorless, while oil-based has an amber tone, which can be good or bad depending on the look you want. 

One of the best stud finders you’ll ever use is the Franklin Sensors ProSensor 710. It’s unique in that there’s a whole bar of red lights that light up whenever it detects a stud. Unlike other sensors, which have a single light that stays on as it passes over the wood, the lights on the 710 tell you exactly where the wood stops and starts. No guesswork. Push a button, drag it over the wall and those hidden mysteries reveal themselves. You won’t even need to read the directions!
Touch ‘n Foam’s Gel Foam Subfloor Adhesive might make you want to chuck your caulking gun for good. It comes in a can and dispenses just like the spray-foam insulation everyone is familiar with. It lays down a bead way faster than tube adhesives but without the endless, wrist-busting trigger squeezing. And you’ll be able to keep working up to 10 times longer without stopping to reload. There’s no downtime due to wet or frozen lumber, and the can is reusable up to 15 days. To use Touch ‘n Foam Subfloor Adhesive, you’ll need an applicator gun (the same one used for expanding foam). There’s also a 46-in.-long barrel for the applicator gun that will save your back from a whole lot of bending over.
The Wilton ATV All-Terrain Vise is a tool for those of you who work out of your pickup at job sites and need a serious on-site vise. And this vise is worth the price! It slips into any 2-in. receiver hitch and has a sizable flat anvil area for pounding. It comes with a bracket for attaching to any sturdy surface, such as a trailer, if you don’t want to use your truck.
A dispensing gun allows you to save foam if the job requires less than a full can. Once the job is finished, just set the gun aside until the next time you need it. Leave the can on the gun if you know it will be used in less than 30 days, or pull the can off, cap it and then clean out the gun with cleaning solution. Besides saving you money on foam, the dispensing gun provides much greater control because you’re not working with a flimsy straw, and the trigger can be adjusted with a turning setscrew to control the rate of flow—nice! Spray foam dispensing guns are available online and at home centers.
There are lots of clear finishes. But for a combination of usability and durability, you can’t beat polyurethane. Oil-based poly, which dries slower than water-based, is best for beginners because it allows more working time. The other important difference is clarity: Water-based poly is absolutely colorless, while oil-based has an amber tone, which can be good or bad depending on the look you want.
Hey Cara – We bought MinWax wooden stain in Cherry (the teeny, tiny can) and one other color, but it has been misplaced in the garage somewhere. We picked up sample sized containers of paint in Satin finish (we bought them at Lowe’s so it was Olympic brand). I just found pretty blue and dark red paint chips and the paint counter guy did the rest! Hope that helps – happy to answer questions if you need any more info

It’s important to have an understanding of wood when building DIY furniture projects. Not just how to cut, and assemble with wood but also to understand how it works. In Mistakes with Wood Can Cause Your DIY Furniture to Crack we talked about how wood is hygroscopic. Simply put, hygroscopic means it absorbs moisture from the air. Seasonal changes cause wood to absorb and release moisture.


Aside from the privacy it offers, a latticework porch trellis is a perfect way to add major curb appeal to your home for $100 or less. The trellis shown here is made of cedar, but any decay-resistant wood like redwood, cypress or treated pine would also be a good option. Constructed with lap joints for a flat surface and an oval cutout for elegance, it’s a far upgrade from traditional premade garden lattice. As long as you have experience working a router, this project’s complexity lies mostly in the time it takes to cut and assemble. Get the instructions complete with detailed illustrations here.

The end grain of wood soaks up finishes and often turns much darker than the face grain. Check for this on your test block. If you get an ugly result, pretreat the end grain with a dose of finish that will limit absorption (wood conditioner, sanding sealer, shellac or polyurethane thinned 50 percent). Apply the treatment with an artist’s brush and be careful not to slop onto the face grain.


The result of this project is what your wife or girlfriend would call a “Rustic,” “Barn,” or “Ranch Style” dining room table. I call it a man table, because it’s made from inexpensive wood, can take a beating, and one day your grandchildren will be serving their kids Thanksgiving dinner on it. Being the man that built that table is, well, manly. I’ve found a few similar tables on Craigslist and furniture sites, starting at around $1200. That’s absurd. I built mine for less than $200, including the chairs I bought for it.
Reclaimed Wood from Corn Crib HOW TO DESIGN AND BUILD AN ENTRY WAY COAT RACK AND BENCH There was a door in granddad’s home the client wanted to preserve and wondered, if they provided the wood, could I build an entryway coat rack and bench using the door as part of the build. The wood they wanted to provide, well, that was from the family owned Tennessee corn crib that had been torn down and they didn’t want to lose the wood or the memories. Not only was this a corncrib but it was eventually used by the great grandchildren as a play house. So for the client there are as many memories in this build as there are colors. THIS PROJECT TRULY DEFINES THE “CUSTOM” in BAYNE CUSTOM WOODWORKING. I spent some time to design a simple layout in @sketchup_official so the client could approve the idea I had in mind. The wood showed up in two deliveries so we stacked it outside because this was the first time I worked with barn wood. I did not want to introduce possible termites to my shop. So my first call was to my pest guy asking how I would treat the wood for termites. Much to my relief he said I had nothing to worry about. This was “real” wood! Not nominal at all, nominal is how we buy our wood at a local hardware store. Where a 2×4 is actually 1 ½  x 3 ½ . These 2×4’s were at least 2”x4”’s if not more and were hard, heavy and dusty, did I say heavy? After cutting to length on my handy @DewaltTough miter saw, I had to take them to my @ridgidpowertools table saw and square up the bottoms only.  I was very careful not to lose any of the original saw marks and character because that would ruin the entire purpose. For someone who likes clean, crisp edges, this was a bit of a challenge. I used @kregjig Kreg Jig® K4 Master System to join all the pieces of the base, the seat frame and the supports to join the two together. I was very careful to hide all of the pocket holes so they could not be seen from any angle. I used Titebond Products original interior wood glue to join all the pieces together. The next item was to assemble the back which included grandad’s door as the center piece. The door was only 71 ½ tall which determined the overall height of the project. Part of this back also includes two live edge pieces that we picked to use as the “L” shaped wings or side walls. The door measured 24” which left me with 6” on each side to make up the final size of 36”. So I chose two of the straightest boards that were closest to 6” and cut them to width so as not to waste any wood or lose any character. I used the Kreg Jig® K4 Master System
A magnetized screwdriver or driver bit makes starting screws a lot easier. It’s like having an extra hand to hold the screw. We also like to magnetize a screwdriver when working with tiny screws that are nearly impossible to find if you drop them (been there?). You can use a magnetic bit holder in most cases, but not in tight quarters. Instead, you can just magnetize the bit. We’ve even magnetized tweezers to help pick up tiny parts.
If you can beg or borrow a pocket hole jig you dont have to predrill holes. I haven’t done a table top other than a workbench(Plywood!) but I have done cabinets and beds. The Kreg jig makes joining easy. A lighter stain colour would cut down on the grain marks, or a heavier application like an espresso stain. I will throw you a pic when I finish my table and show you what I mean. 

The owners, webmasters, administrators, authors and editors, expressly disclaim all and any liability to any person, whether a user of this website or not, in respect of anything and of the consequences of anything done or omitted to be done by any such person in reliance, whether whole or partial, upon the whole or any part of the contents of this website. Please exercise caution when working with any tools or machinery. Follow common safety rules and precautions as outlined in any manuals related to the equipment being used. If advice or other expert assistance is required, the services of a competent professional person should be sought.


Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth. It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed.
If you’re like me, every time you wander through a big-box furniture store, you feel a little insulted. Here you are, a man, staring at relatively simple furniture, being asked to lay down large sums of money for a bookshelf, dining set, or desk. And if you know enough about wood to spot laminate and fiberboard, you’ll quickly see these expensive pieces of furniture have a shelf life (no pun intended) of about two years.
These unique clamps will save you time and aggravation in too many ways to list! MatchFit clamps slide anywhere along a groove routed with a common 1/2" - 14 degree dovetail bit and leave one surface of your work clear of obstructions. Use these clamps to create customizable clamping tables and for attaching table extensions, sub fences, stop blocks, hold downs, and more to your machinery and work tables. Imported.
When it comes to choosing a finish there are two main choices. The typical approach of stain and urethane creates a smooth, wipeable surface, but when that finish eventually wears through, there’s no way of repairing it attractively. Sanding back to bare wood and refinishing is the only way to make it respectable again. Oil and wax finishes, on the other hand, take more time to apply initially, but they’re easily repaired and rejuvenated with the tabletop in place. Regular reapplication works just fine.

You can also use Google image search to research a project. Unlike the PDF search, the image search provides a photo of what the project will look like, which is helpful in determining if you want to pursue building it. By doing an image search for how to build a step stool, you will have a ton of options that all lead to woodworking plans of various quality. (The how to part of these is important—otherwise you’ll just get pictures of step stools.)


​Luckily, we have also managed to find a detailed video tutorial of the Barn door project that illustrates the process of building a Barn door of your own. The steps and instructions in the video tutorial are different from the source links listed above. Actually, you can make different types of designs for your Barn door depending on which one you can afford easily and DIY on your own.
This super-strong and simple-to-build workbench is may be the project you've been looking for a long time. You have to select some free workbench plans to create yourself a working table in your shed that after you can use it when you are working on your projects and maybe it can provide you some extra storage, depends upon which plan you are choosing to DIY.
The best thing about the toy chest is that it is very easy to build. All you need is the basic understanding of woodworking and a few tools to get started. You can also modify your kid’s toy chest in any way you want or build in a different design or color different from the one pictured above. You can try some other designs for your plan in the below-mentioned link.
It is becoming more popular in this DIY age for people to want to make things themselves, and we are seeing a return to woodworking as a hobby or pastime. The garage is transformed into a workshop, with a workbench a set of woodworking tools and of course a beer fridge. Beautiful handmade woodworking projects can be achieved with some practice, a good set of plans and the right woodworking tools.
It might sound weird but you can actually turn an old window into a lovely coffee table. You just need to attach four legs and a handle and you have an original coffee table with a clever storage space inside. If the window already has the dimensions you wanted then it’s perfect. If not, you can adjust your project. You can also feel free to repaint everything.{found on ohgloryvintage}.
The deep grain lines in woods like oak or walnut will telegraph through the clear finish, no matter how many coats you apply. And that’s fine; it’s part of the character of coarse-grain woods. But if a perfectly smooth surface is the look you want, use a grain filler. You’ll find several products online or at woodworking stores. With most, you wipe on the filler, squeegee off the excess with a plastic putty knife and then sand after it’s dry for a smooth-as-glass surface.

A few days back, I was searching for some cool DIY plans. So, I got to work and ended up coming up with some easy to follow project and an awesome new ice chest cooler to have out on the deck! It was going to be perfect for summer hangouts and barbecues. It was a fun and practical plan to work on and I know you will have fun tackling select a design from this plan and start building your own. Enjoy learning how you can build a rustic cooler also sing the video tutorial and source tutorial plan!
We cut the supports 16 in. long, but you can place the second shelf at whatever height you like. Screw the end supports to the walls at each end. Use drywall anchors if you can’t hit a stud. Then mark the position of the middle supports onto the top and bottom shelves with a square and drill 5/32-in. clearance holes through the shelves. Drive 1-5/8-in. screws through the shelf into the supports. You can apply this same concept to garage storage. See how to build double-decker garage storage shelves here.
Every woodworker needs a couple of levels. You probably won’t need one of the 6-foot levels used in construction, but 48” is a good length for many of the woodworking projects you’ll do. Usually, you’ll also need an 8” level too, usually known as a torpedo level. You’ll check the level and plum of your construction. Level means horizontal, and plumb is vertical.
If you sand through the polyurethane and remove some stain, you can touch up with more stain. But the repair won’t be perfect, so take pains to avoid that mistake. Sand very lightly after the first coat, just enough to remove the dust whiskers. After the second coat, you can sand a little harder to flatten larger flaws. Always be careful around the edges of the table; that’s where it’s easiest to sand through.
×