This is a very colorful and fun project. The idea is to use an old table with a top that you don’t really like and to give it a makeover. You don’t need paint for this project, just a lot of colored tape. Use it to make stripes to cover the entire surface of the tabletop. You can also wrap the edges in tape. You can also cover it with lacquer or add plexiglass on top to protect the design.
If you already have a workshop and the skills for woodworking, you will need to make sure that you have some reliable woodworking plans at your disposal and the necessary woodworking tools to complete the projects you wish to make. There are some websites that offer free woodworking plans, but they are often incomplete or lack sufficient detail to understand properly and this will lead to frustration and loss of interest in woodworking. After spending many years building up your collection of fine woodworking tools and learning to use them, you will no doubt have some neat skills under your belt. Now to make full use of these skills, you will need to find a nice project to work on, one which will do you proud and show off your fancy woodworking skills.
Here’s a traditional Swedish farm accessory for gunk-laden soles. The dimensions are not critical, but be sure the edges of the slats are fairly sharp?they’re what makes the boot scraper work. Cut slats to length, then cut triangular openings on the side of a pair of 2x2s. A radial arm saw works well for this, but a table saw or band saw will also make the cut. Trim the 2x2s to length, predrill, and use galvanized screws to attach the slats from underneath. If you prefer a boot cleaner that has brushes, check out this clever project.
This DIY has a bit of a backstory: In my basement workshop—as a byproduct of about a half dozen previous projects—I’d managed to accumulate a small mountain of scrap wood. Though the pieces varied in size, most were 2×4 boards. For weeks, I pondered the question of how to use them. There wasn’t enough material to build anything substantial, but at the same time, this was much more wood than I would feel comfortable chucking or committing to kindling. I suddenly seized on the idea of turning those leftover boards into a rustic tabletop, but then I let the project momentum slow to a creep, and in the blink of an eye another few weeks had gone zooming by. Things finally came to a head one day when I was scanning the local giveaway listings. There, I discovered that one of my neighbors was trying to get rid of an old metal garden table. Upon seeing the pictures, I knew immediately that this would be a great table to top with the scrap wood surface I’d been planning to make with all those 2x4s!
Attach all four legs and set the top on the base with equal overhang on all sides. Carefully trace the leg tops on the bottom side of the planks and then flip it over onto a work surface. Drill a 1/2” hole with each square mark near the line but not touching it. Using a jigsaw, carefully cut out each square. Because leg tops will nest snuggly in these squares, be sure cuts are slightly undersized. Flip the top back over and attempt to set it on the base. Using a flat wood file and chisel, remove small amounts of material as needed. Once the top nestles down on the gutter structure without excess force, run a small bead of wood glue on the top edges of the gutter, reposition the top and shoot 15-gauge finish nails through the inside edge of the gutter into the bottom of the tabletop. Fill in small gaps between the leg top and table planks with wood filler or small wood shims.
And if you haven’t got a fancy stencil hanging around, you can still give your table a stencil-styled makeover, and it won’t take much.  To make this fun herringbone table, Shark Tails took a boring side table and taped off a herringbone design then spray painted it gold!  It adds a touch of mod glam that’s not overwhelming since it’s in a small dose. // Shark Tails
Do you want to use an oil stain, a gel stain, a water-based stain or a lacquer stain? What about color? Our ebook tells you what you really need to know about the chemistry behind each wood stain, and what to expect when you brush, wipe or spray it on. It’s a lot simpler than you think! This is the comprehensive guide to all the varieties of stain you will find at the store and how to use them.
This is a very colorful and fun project. The idea is to use an old table with a top that you don’t really like and to give it a makeover. You don’t need paint for this project, just a lot of colored tape. Use it to make stripes to cover the entire surface of the tabletop. You can also wrap the edges in tape. You can also cover it with lacquer or add plexiglass on top to protect the design.

Clamp curved caul edges inwards so they align tabletop boards in the middle, then torque up the main clamps to draw the boards together. If the width of boards you’re using allow it, pre-glue boards for your tabletop in sections that are just narrow enough to fit within your thickness planer. Run these through the planer to clean and level the glue joints, then move back to clamps for final glue up. Working in stages like this reduces the number of glue joints you need to sand smooth and level later.
When you are gathering inspiration for barn door Plan, be sure to note the cost of the tools used in the plan. Barn door tools can often cost more than your actual door! But, there are many clever and affordable do it yourself tools options in the tutorials mentioned below! Let us explore some DIY Barn Door Tutorials. Just click on the blue text below and check some amazing fun Barn doors. They might be different from the one shown in above picture.
PROCESSING NOTES: No matter how easy I have tried to make following these media center plans and constructing them, if you find it overwhelming to attempt the project or operate the basic tools necessary for completion, get help. Contact your local supplier to see if sheet goods can be ripped to fit your car trunk. The possibility of ordering all the parts ready for assembly is also available. Most importantly, when you set off to build your project, help is only an email message away.
Pallet tables are very common and very easy to make. To make it you’ll need about half of a wood pallet. Decide the dimensions for the table and then remove some of the boards and cut them to size. Reattach them using nails and then sand the table. Then you can stain or seal the wood if you want. At the end, you can either add legs, casters or leave the table as such.{found on hernewleaf}.

Keep your woodworking tools and knives razor-sharp with our wide variety of sharpening supplies and accessories. We have what you need for jointer and planer knife sharpening. For sharpening plane irons and chisels, we supply a variety of diamond and waterstones, the Infinity Sandpaper Sharpening System, and honing guides. Our power sharpening systems include the Worksharp Knife Sharpeners, Ken Onion edition for the sharpest knives in the drawer.
This plan is probably the easiest plan ever added in the list. The one who is working on this project, don’t need any professional skills but just knowing some basics of woodworking will be enough for this DIY. You will get step by step detailed process of this tutorial in the source linked tutorial. This tutorial will surely help you to build this plan quickly.
Okay, let’s stain this beast. I should explain that we used Rustoleum’s Dark Walnut Ultimate Wood Stain, but we did it wrong. We failed to mix it well before applying it, resulting in a color we really liked–but not the color this stain is designed to create. When we came back to do a second coat, we stirred it well, resulting in a coat that looked like purple paint. I had to sand it off and start over. So, don’t follow my lead here–follow the can’s directions and TEST before staining all of your new masterpiece!
×