Pallet tables are very common and very easy to make. To make it you’ll need about half of a wood pallet. Decide the dimensions for the table and then remove some of the boards and cut them to size. Reattach them using nails and then sand the table. Then you can stain or seal the wood if you want. At the end, you can either add legs, casters or leave the table as such.{found on hernewleaf}. 

Rachel Teodoro and Holy-Craft.com, 2010-present. Unauthorized use and/or duplication of this material without express and written permission from this site’s author and/or owner is strictly prohibited. Excerpts and links may be used and up to one photo can posted, provided that full and clear credit is given to Rachel Teodoro and Holy Craft with appropriate and specific direction to the original content.
A super simple iPad Dock/stand made out of a single block of wood features an angled groove which gets to support the tablet device and a cut in a hole to revise access to the home button of your iPad. It’s possible to drill an access channel in the stand through which you can run a charging cable, although this mini stripped back iPad stand may have very limited functions.
If you want your table top -- any table top -- to actually ast without bowing/cupping/twisting, you MUST attach it in a manner that allows for seasonal wood movement. Wood is an organic product, and it naturally expands and contracts with changes in temperature and humidity. I'll post link below to a couple of options that you can cheaply buy which will allow you to securely attach a tabletop while still giving the wood the flexibility to move with the seasons. When you buy decently-made furniture at a store, they all accommodate for this one way or another. Don't just screw the top down to the legs or the skirt...you'll regret it later on.
This is another very interesting project. To make a similar table you need to have textured spray paint, matte black spray paint, lumber, wood boards, wheels, stain, sand paper, corner pieces, nails, bolts, nuts, washers, clamps and L brackets. First make the measurements and spray paint all the hardware including the wheels. Then make the basic box and sue nails to hold the wood pieces in place. Then use L brackets to keep them sturdy and add the bolts. Tighten the nuts into the bolts and attach the wheels.Then add the corner pieces sing nails{found on theblissfulbeeblog}.
A dispensing gun allows you to save foam if the job requires less than a full can. Once the job is finished, just set the gun aside until the next time you need it. Leave the can on the gun if you know it will be used in less than 30 days, or pull the can off, cap it and then clean out the gun with cleaning solution. Besides saving you money on foam, the dispensing gun provides much greater control because you’re not working with a flimsy straw, and the trigger can be adjusted with a turning setscrew to control the rate of flow—nice! Spray foam dispensing guns are available online and at home centers.
I’ve been toying with the idea of building a new table top. The legs of my dining table are hardwood. But the table top is not; it’s covered in veneer which is coming off in strips. I thought of removing the table top completely and utilizing the existing legs with a newly built hardwood top. But you’re solution seems easier! However, my tabletop is much thicker than yours, a 1 x 1 inch lip would not suffice. Can I just adjust the size of the lip, 1 x 2 inch? Or do I have to adjust the size of all boards used? Thanks!

The most commonly purchased claw hammer is the 20 oz. size. It’s heavy enough to easily drive nails but easily manipulated when pulling nails. While wooden handles are picturesque, they may not stand up to the strain if you have to pull a lot of nails. Hammers with a steel handle, or even fiberglass, will be stronger. However, these won’t absorb the vibrations from driving nails the way a hickory handle will. You’ll also need to make sure the fiberglass and metal handles have a rubberized grip for control and comfort. If you’re going to be driving a lot of nails, the wooden handled hammer will be better for reducing stress on your hand, and wrist, too.
Building a table is one of the most deceptively simple woodworking projects going. What could be easier than gluing up a few boards and applying a finish, right? But reality is often surprising, because building a top for that table can go wrong in ways you might not realize until it’s too late.  Here are my favourite tabletop construction tips, plus advice on how to avoid trouble.

Touch ‘n Foam’s Gel Foam Subfloor Adhesive might make you want to chuck your caulking gun for good. It comes in a can and dispenses just like the spray-foam insulation everyone is familiar with. It lays down a bead way faster than tube adhesives but without the endless, wrist-busting trigger squeezing. And you’ll be able to keep working up to 10 times longer without stopping to reload. There’s no downtime due to wet or frozen lumber, and the can is reusable up to 15 days. To use Touch ‘n Foam Subfloor Adhesive, you’ll need an applicator gun (the same one used for expanding foam). There’s also a 46-in.-long barrel for the applicator gun that will save your back from a whole lot of bending over.
Most construction tasks consist of a series of straight lines, but occasionally you run into a situation that requires an arc or a circle. A trammel is usually the best tool for the job, but there’s only so much room in your toolbox. M. Power makes the Tri-Scribe, which hooks onto tools you already have, like the tongue of a square or a metal ruler, and transforms it into a flat-lying trammel. Strike a circle or an arc from 1 in. to 6 ft.—you’re limited only by the length of your rule. You can either make your mark with a pencil or insert the knife blade and score the surface. Best of all, they take up hardly any room in your toolbox.
When you buy the wood, look for pieces that aren’t warped, excessively longer or shorter than the others, and, if you can get lucky, don’t carry the telltale “new wood” planer marks. We purchased the most inexpensive wood that we could find. You’ll likely find them in 2- and 4-ft pieces. If you have a saw at home, you might consider getting the 4 ft pieces to decrease the cost of your project a bit.
Open rafters and trusses are an endless source of falling dust. So if you’re working under an open ceiling, hang plastic sheeting above. Keep the plastic at least 12 in. from light fixtures or remove the bulbs. Sometimes, adding plastic ‘walls’ is a lot easier than cleaning up the entire area. If you’re using oil-based finishes, hang the sheets about a foot from the floor to allow for ventilation.
Finding a toolbox for a mechanic, for his hand tools, is not a big challenge at all - there are dozens of the tool boxes available on the market, from huge roll-around shop cases to small metal boxes. Plumbers, electricians, and farmers are well served, too, with everything from pickup-truck storage to toolboxes and belts. But, if you are a shop-bound woodworker then the case changes. You get to need a tool box that suits the range and variety of hand tools that most woodworkers like to have. For those who deny making do with second best, there's only one solution, you’ve to build a wooden toolbox that should be designed expressly for a woodworking shop.
California Air Tools makes great air compressors. One of their most popular models is the 2010A. The aluminum tank makes it light (35-lbs.) and eliminates those stains from rusty water draining from rusty tanks. The oil-free dual-piston pump provides a fast recovery time—fast enough to run a framing gun. It also draws less power and performs well in cold weather. There’s no doubt that you’re going to like all the features of this compressor, but you’re going to love how quiet it is. It runs at about 60-dB, which is about the same as a conversation in a restaurant. So, no more hollering at coworkers or cranking up the radio to hear the music over a screaming compressor.

If you already have a workshop and the skills for woodworking, you will need to make sure that you have some reliable woodworking plans at your disposal and the necessary woodworking tools to complete the projects you wish to make. There are some websites that offer free woodworking plans, but they are often incomplete or lack sufficient detail to understand properly and this will lead to frustration and loss of interest in woodworking. After spending many years building up your collection of fine woodworking tools and learning to use them, you will no doubt have some neat skills under your belt. Now to make full use of these skills, you will need to find a nice project to work on, one which will do you proud and show off your fancy woodworking skills.

In an effort to replace the table, I started looking at garage sales and on craigslist for replacements. I was coming up empty handy {they all looked worse than ours!} or being totally priced out.  I started to think, why not just use the table that we have and slap a few boards on it.  My engineer husbands thinking is a little more refined than "slapping" boards on something, so he came up with an idea {and like a true engineer made an auto cad design}, we tweaked it a bit together and then took a little date to Home Depot. Because that my friends, is where adults go on dates.
There’s a lot of space above the shelf in most closets. Even though it’s a little hard to reach, it’s a great place to store seldom-used items. Make use of this wasted space by adding a second shelf above the existing one. Buy enough closet shelving material to match the length of the existing shelf plus enough for two end supports and middle supports over each bracket. Twelve-inch-wide shelving is available in various lengths and finishes at home centers and lumberyards.
Check out our most recent woodworking tools and accessory reviews below. We have thousands of satisfied customers that use our router bits, shaper cutters, router tables, and many more fine woodworking tools every day. Take a minute to read what your fellow woodworkers have to say about their experience with our company and our quality woodworking tools. All reviews are from real customers of Infinity Tools who were polled by our partners at ShopperApproved.com. More third party reviews can be found at Shopper Approved's website. 

Diablo's 3-piece Adjustable Cabinet Router Bit Set features Diablo's 3-piece Adjustable Cabinet Router Bit Set features a rail and stile bit set and a Double Shear raised panel bit. Featuring TiCo carbide with titanium these bits provide a long cutting life and ultra-fine finish. Perma-Shield Diablo's high performance coating reduces friction and build-up on the bits. The bits ...  More + Product Details Close
No, it’s not a blood pressure tester. It’s an inflatable shim sold by Calculated industries. What in the world would you do with an Air Shim? Well, you could hold a window in position (by yourself) while setting the permanent shims, or prop up a door slab during installation without scratching the hardwood floor. Use it to align base cabinets or level appliances. You could even trick your big, burly buddy by betting him that your 10-year-old can pick him up off the ground… you will win that bet because the Air Shim is easy enough for anyone to pump and it holds up to 300-lbs. Deflate it as slow as you want for uber precision adjustments.
Furnishing and decorating your patio is not an easy task – but then again, it has to be done! Your patio is obviously one of the most important rooms in your home, as you can easily turn it into your little piece of Heaven, your “safe spot” in your home where you can retreat whenever you want to ignore the world and just spend some time alone all by yourself. 

The most commonly purchased claw hammer is the 20 oz. size. It’s heavy enough to easily drive nails but easily manipulated when pulling nails. While wooden handles are picturesque, they may not stand up to the strain if you have to pull a lot of nails. Hammers with a steel handle, or even fiberglass, will be stronger. However, these won’t absorb the vibrations from driving nails the way a hickory handle will. You’ll also need to make sure the fiberglass and metal handles have a rubberized grip for control and comfort. If you’re going to be driving a lot of nails, the wooden handled hammer will be better for reducing stress on your hand, and wrist, too.
Nightstand table plans have everything you need to create a bedside table to keep every needy thing at reach at night time. This Nigh Stand plan is quite different in design from the most of the other plans. This stand has not only the three regular drawers but also having a hidden drawer that uses a secret locking mechanism to keep contents securely.
Crisp, tight joints are key to any great tabletop, and this is where the jointer comes in. Get help supporting boards longer than about five feet as you work. Also, if some joints don’t come together tightly, despite your best jointing efforts, try moving the boards to new locations if grain patterns permit. Some edges just naturally fit together more tightly than others. Don’t own a jointer? Pieces of planed lumber sometimes fit together just fine without jointing. Try different boards as neighbours to see which ones get along the best.

No, it’s not a blood pressure tester. It’s an inflatable shim sold by Calculated industries. What in the world would you do with an Air Shim? Well, you could hold a window in position (by yourself) while setting the permanent shims, or prop up a door slab during installation without scratching the hardwood floor. Use it to align base cabinets or level appliances. You could even trick your big, burly buddy by betting him that your 10-year-old can pick him up off the ground… you will win that bet because the Air Shim is easy enough for anyone to pump and it holds up to 300-lbs. Deflate it as slow as you want for uber precision adjustments.
This is another very interesting project. To make a similar table you need to have textured spray paint, matte black spray paint, lumber, wood boards, wheels, stain, sand paper, corner pieces, nails, bolts, nuts, washers, clamps and L brackets. First make the measurements and spray paint all the hardware including the wheels. Then make the basic box and sue nails to hold the wood pieces in place. Then use L brackets to keep them sturdy and add the bolts. Tighten the nuts into the bolts and attach the wheels.Then add the corner pieces sing nails{found on theblissfulbeeblog}.
Drill four 5/8-in.-dia. 1/2-in.-deep holes on the large disc?inside the traced circle?then use 5/8-in. dowel centers to transfer the hole locations to the underside of the small disc. Drill four 1/2-in.-deep holes on the underside of the small disc and a 1/2-in.-deep hole in the center of the top for the dowel handle. Glue in the dowels to join the discs, and glue in the handle. We drilled a wood ball for a handle knob, but a screw-on ceramic knob also provides a comfortable, attractive grip.
Personally identifying information is information that can be used to identify who you are such as: name, mailing address, email address. To enter certain areas of the site, you will be required to register and provide information about yourself. This information is for the purposes of Canadian Woodworking and helps us to tailor the site to best meet the needs of our audience. 
This plan is probably the easiest plan ever added in the list. The one who is working on this project, don’t need any professional skills but just knowing some basics of woodworking will be enough for this DIY. You will get step by step detailed process of this tutorial in the source linked tutorial. This tutorial will surely help you to build this plan quickly.
Creating a classic toy: One of my favorite shop projects is to create children’s cedar building blocks from rough Tennessee red cedar. These came about after I built my first Adirondack chairs and I had a large amount of scrap wood left over. Our first granddaughter had just been born and we decided to build a set of building blocks. Since that first set of blocks was made I’ve delivered hundreds to young children all across the country. Hearing the stories of the kids playing with these for hours and seeing the joy on their faces is what it’s all about. *DISCLOSURE: Some of the links below are affiliate links. If you chose to click through and make a purchase I will earn a commission but there is no additional cost to you. It helps compensates the business for the time spent creating these posts. THANK YOU! Start with Rough Cut Cedar These blocks start with rough 2×4 and 2×6 cedar lumber purchased from my local cedar mill. I use my Ridgid Power Tools Surface Planer to bring the wood into smooth milled lumber. Over to the SuperMax Drum Sander to sand the wood as much as possible. The goal is make sure the wood is as soon as glass. Then the wood goes into my Ridgid table saw to be milled into ¾ x ¾, 2 x 2 and ¾ x 2. Once the pieces are cut to proper width its over to the Grizzly Band saw to cut the blocks to length. I tried to do this on my sliding miter saw, but found I could not control the blocks well enough and the saw blade would cause them to either get jammed or fly across the shop and be ruined. Block Sizes These blocks come in a number of rectangle and square sizes. ¾ x ¾ x 2”, 4” and 6” ¾ x 2 x2’, 4” and 6” 1 ½ x1 ½ x1 ½ 2 x2 x 2”, 6” Final Step by Hand The last step is to take them to the Ridgid Oscillating Sander and round over the edges and corners to keep them safe. Because we handle them multiple times it gives is the opportunity to clear out any misfits and chipped blocks. Watch the process here. At one point we were coating them with a finish used for salad bowls but they were hard to dry without leaving ridges from the drying racks or drips that needed to be sanded off. It was recommended/suggested by a number of mothers that we not put anything on them. The beauty of these blocks is they hold the smell and are safe to play with. They provide hours of fun when stacking and building. I have watched the little ones learning how to pick things up grab and hold them. Available to purchase on Etsy Interested in having your own set? We have a limited amount available for Christmas 2018 with or without the hand made wooden
We recently upgraded a wheelbarrow with Simply Dump It pivoting handles. They slid right over the handles and took about five minutes to install. If you’re tall, you probably hunch over when you roll your wheelbarrow around the yard so you don’t end up nose-diving the wheel guard/brace into the ground, resulting in messy spills and the occasional expletive. The Simply Dump It handles raise the grip location a few inches, which lowers the handles, which in turn raises the front wheel brace. The handles not only prevent sudden stopping syndrome but also make the wheelbarrow easier to control, especially on rough terrain. And the pivoting action all but eliminates the awkward torque on your wrists when you empty the wheelbarrow. You can get Simply Dump It handles online.
To save money, we keep the temp in our shop down low when we’re not in it and crank up the heat when we return. But even when the air temperature hits 70 degrees F, the concrete floor is still Minnesota-cold. We tried a space heater under the bench, but it broiled the shins and still left us with cold feet. So we recently bought a foot-warming mat, and now our feet stay toasty warm. Plus, it uses a fraction of the electricity and is a lot safer than a space heater. The mat is produced by Cozy Products. The good folks over at Cozy suggest putting a chunk of cardboard underneath it if you use it on flooring that could fade from the heat, like carpet or wood.

Open rafters and trusses are an endless source of falling dust. So if you’re working under an open ceiling, hang plastic sheeting above. Keep the plastic at least 12 in. from light fixtures or remove the bulbs. Sometimes, adding plastic ‘walls’ is a lot easier than cleaning up the entire area. If you’re using oil-based finishes, hang the sheets about a foot from the floor to allow for ventilation.


OK, the Long Ranger’s been around since Marconi. But we love it. Simply put, this Long Ranger III Remote Dust Collector Switch is a remote system for turning on your dust collector out in the shop from whatever tool you’re operating. It plugs into the wall, you plug your dust collector into that and you’re done. Push the button on your remote and it fires right up. It’s saved us about two years and 1,300 miles of walking back and forth to the dust collector switch.
Reclaimed Wood from Corn Crib HOW TO DESIGN AND BUILD AN ENTRY WAY COAT RACK AND BENCH There was a door in granddad’s home the client wanted to preserve and wondered, if they provided the wood, could I build an entryway coat rack and bench using the door as part of the build. The wood they wanted to provide, well, that was from the family owned Tennessee corn crib that had been torn down and they didn’t want to lose the wood or the memories. Not only was this a corncrib but it was eventually used by the great grandchildren as a play house. So for the client there are as many memories in this build as there are colors. THIS PROJECT TRULY DEFINES THE “CUSTOM” in BAYNE CUSTOM WOODWORKING. I spent some time to design a simple layout in @sketchup_official so the client could approve the idea I had in mind. The wood showed up in two deliveries so we stacked it outside because this was the first time I worked with barn wood. I did not want to introduce possible termites to my shop. So my first call was to my pest guy asking how I would treat the wood for termites. Much to my relief he said I had nothing to worry about. This was “real” wood! Not nominal at all, nominal is how we buy our wood at a local hardware store. Where a 2×4 is actually 1 ½  x 3 ½ . These 2×4’s were at least 2”x4”’s if not more and were hard, heavy and dusty, did I say heavy? After cutting to length on my handy @DewaltTough miter saw, I had to take them to my @ridgidpowertools table saw and square up the bottoms only.  I was very careful not to lose any of the original saw marks and character because that would ruin the entire purpose. For someone who likes clean, crisp edges, this was a bit of a challenge. I used @kregjig Kreg Jig® K4 Master System to join all the pieces of the base, the seat frame and the supports to join the two together. I was very careful to hide all of the pocket holes so they could not be seen from any angle. I used Titebond Products original interior wood glue to join all the pieces together. The next item was to assemble the back which included grandad’s door as the center piece. The door was only 71 ½ tall which determined the overall height of the project. Part of this back also includes two live edge pieces that we picked to use as the “L” shaped wings or side walls. The door measured 24” which left me with 6” on each side to make up the final size of 36”. So I chose two of the straightest boards that were closest to 6” and cut them to width so as not to waste any wood or lose any character. I used the Kreg Jig® K4 Master System
In an effort to replace the table, I started looking at garage sales and on craigslist for replacements. I was coming up empty handy {they all looked worse than ours!} or being totally priced out.  I started to think, why not just use the table that we have and slap a few boards on it.  My engineer husbands thinking is a little more refined than "slapping" boards on something, so he came up with an idea {and like a true engineer made an auto cad design}, we tweaked it a bit together and then took a little date to Home Depot. Because that my friends, is where adults go on dates.
Rachel Teodoro and Holy-Craft.com, 2010-present. Unauthorized use and/or duplication of this material without express and written permission from this site’s author and/or owner is strictly prohibited. Excerpts and links may be used and up to one photo can posted, provided that full and clear credit is given to Rachel Teodoro and Holy Craft with appropriate and specific direction to the original content.
×