Breaking down heavy sheet-goods on a jobsite table saw is difficult, and dang near impossible when working alone. That’s where a track saw comes in handy. A good quality track saw can produce cabinet saw results out on any job. Now, this portable tool is even more portable. The FESTOOL TSC 55 is a cordless saw that has the same features and performs just as well as FESTOOL’s corded saw, including the cut capacity and blade speed. It also has a collection bag that actually works, collecting up to 90% of the dust. The batteries are compatible with other FESTOOL products and the saw runs on their standard tracks.
**Important!  Be sure to pre-drill the holes for your screws before attaching the base to the table top!!  If you read the blog, then you know my table top ended up splitting, starting at a knot on the edge.  I’m pretty sure the cause of this was the fact that I attached the base to the top with screws without pre-drilling the holes, and I screwed right into a weak spot at the knot.  Learn from my very frustrating mistake, and don’t try to take short cuts!!
This is another wood table but this time with a more elaborate design. Instead of using a large log, this time you’ll need several small ones. The idea is to cut them to the same height and to try to create a mosaic with them. You can glue them together and you can also wrap a piece of rope or something similar around them. You should be able to create an original coffee table.
You’ll need a long screwdriver with a square blade that is very heavy duty. This gives you a lot of torque. You’ll also need a small and medium slot screwdriver. For working on cabinets or tight places in woodworking, you’ll need a screwdriver with a thin shank so that you can reach screws that are inside of deep holes. This is accomplished with a cabinet screwdriver. Get a couple of medium Phillips head screwdrivers, and a stubby one too, for those tight places. You may also want a ratcheting screwdriver.
Cut off a 21-in.-long board for the shelves, rip it in the middle to make two shelves, and cut 45-degree bevels on the two long front edges with a router or table saw. Bevel the ends of the other board, cut dadoes, which are grooves cut into the wood with a router or a table saw with a dado blade, cross- wise (cut a dado on scrap and test-fit the shelves first!) and cut it into four narrower boards, two at 1-3/8 in. wide and two at 4 in.
Example Entertainment Center: $25 for plans + $750 for materials + $1200 for good quality tools = $1975. Less than a few grand! Of course you don't have to buy brand new tools; search the sale lists online (i.e. Craigslist, Freecycle.org, etc.) in your area. You are sure to find some good deals on power tools and even materials! (A good set of tools includes a table saw, miter saw, nail gun and compressor and four piece cordless tool set.)
Online packages also allow you to build at a convenient pace, whether you want to build one bench per week or want to try every new furniture plan available – and more importantly, the use of clear instructions will enable you to build under a comfortable environment without any pressure. That way, you do not face disappointment that you would otherwise experience if you buy hard-to-understand furniture plans or can’t find the specific project that you’re looking for. If you think that a plan outline is simple, you can find a more difficult one and begin practicing new skills and techniques. That way, you are able to build more things faster than if you bought each plan individually and had to search for it each time.
Yes Seriously! You can build an easy bed frame yourself without any other’s help. As everyone knows the starting point of any bedroom is a gorgeous bed. However, you also need something that lets you enjoy peaceful slumber in comfort and warmth, but since the bed took as the focal point of the room, you may need something that looks really good too.
Although it’s tempting to use a random orbit sander to smooth your table top at the final stages, I never do. Finish quality is the reason why. Random orbit sanders often leave behind swirl marks that don’t show up until finishing time. A better option is to complete the sanding process by hand, using 180-, then 220-grit paper only in the direction of wood grain. The finish of a tabletop is more closely examined than wood finishes anywhere else, so you need to eliminate all flaws.

I am so glad to see this. It is exactly what I have been looking for. I have had a similar idea in my head for years but didn't know how to bring it together, and I wasn't sure how it would actually turn out. Yours is beautiful. It is nice to start with an idea of how the project will actually look when I am done. My table is 25 years old with a laminate top. The reason I want to cover instead of replacing it does that it is the first purchase my husband and I made together. It has seen 25 years of abuse by three little (now big!) boys and by me, the messy crafter. But I cannot imagine ever getting rid of this table. Plus it's not like I'm going to get less messy, so investing in an expensive table would be crazy. I love how I can take this top off and still do the messy damaging things on it. I am bookmarking this and if I ever get around to actually doing it LOL, I will send you pics
There’s a lot of space above the shelf in most closets. Even though it’s a little hard to reach, it’s a great place to store seldom-used items. Make use of this wasted space by adding a second shelf above the existing one. Buy enough closet shelving material to match the length of the existing shelf plus enough for two end supports and middle supports over each bracket. Twelve-inch-wide shelving is available in various lengths and finishes at home centers and lumberyards.
Well I certainly can say most times when anyone comes into my shop they always ask….what’s this do?...lol Although not my own design I do get many questions on the German Springpole Lathe from Roys last book. It’s always a fascinating conversation piece…and usually gets people that have never worked wood really interested and wanting to learn more. When I show them spindels and how it works I always get an impressed or entertained reaction.
With a pencil and a protractor, divide the larger disc into 30-degree wedges to create 12 center lines for the bottle indents. Center and trace the smaller disc on top of the larger disc. Next, with a drill press, drill 3/8-in.-deep holes on the 12 center lines with the 1-7/8-in. Forstner bit, spacing them between the disc’s outer edge and the traced circle. Next, divide the smaller disc into 60-degree wedges and drill six more 3/8-in.-deep holes with the Forstner bit.
Holy Craft came up with a genius solution for a scratched and worn dining table!  If your table looks a little worse for wear, but you still plan on using it for messy situations like painting and crafting, you’ll love this wood plank tabletop cover.  Slide it on for nice dinners and entertaining company, and tuck it away when your kids use play dough! // Holy Craft on Remodelaholic
Google is probably the first place where most people would start searching for woodworking plans, but often the top results can be a mix of articles and how-to pieces that just aren’t detailed enough. Sometimes they’ll link to the plans (like we try to here at Lifehacker), but other times, they’re just showing off a cool project. There are better, more precise ways of finding what you’re looking for.
Another fairly inexpensive option for making a table top is using a stain grade 3/4″ plywood. cut the 4 x 8 sheet in half (2- pcs, 4 x 4). Spread wood glue one and place and clamp the other on top. Once the glue has dried, it can be cut with a jig saw to the round shape, or if you have access to a router, make a “circle cutter” by mounting the router on a thin piece of wood, (1/4 x 6 x 60″) and putting pivot hole at a distance of 1/2 the diameter of the desired table. (from the side of the router bit to the pivot hole. Put a small hole in the underside of the table top as close to the center as possible. (not all the way through) and use something like a nail as a pivot. Use a straight bit and cut a perfect circle. The stain grade plywood usually has a pretty good stain surface and the construction of the plywood makes it pretty stable. After cutting the edge may have some minor voids, which can be filled with wood putty and sanded nice and smooth. The results can be a nice stained or painted surface.
Drill pocket holes from the outer boards to the inner board. Drilling the holes before adding screws prevents the boards from cracking. To create the holes, measure along the sides of the center board. Mark it about every 7 in (18 cm). You will need to use a very long drill bit, about 3 in (7.6 cm) wide, called a pocket hole drill bit. Drill at an angle down through the side boards and into the side of the center board every 7 in (18 cm).[4]
The table tops are double-sided – two for one! – and are 2 feet square. The cost of the project will vary based on items you might already have but the biggest expense is the wood at about $25 – that’s $12.50 per “table” – not too shabby at all, especially when you think about the alternative of actually buying an entire table. Or the gigantic house you’d need to store all that extra furniture!
If you sand through the polyurethane and remove some stain, you can touch up with more stain. But the repair won’t be perfect, so take pains to avoid that mistake. Sand very lightly after the first coat, just enough to remove the dust whiskers. After the second coat, you can sand a little harder to flatten larger flaws. Always be careful around the edges of the table; that’s where it’s easiest to sand through.

Pallet tables are very common and very easy to make. To make it you’ll need about half of a wood pallet. Decide the dimensions for the table and then remove some of the boards and cut them to size. Reattach them using nails and then sand the table. Then you can stain or seal the wood if you want. At the end, you can either add legs, casters or leave the table as such.{found on hernewleaf}.


Reclaimed Wood from Corn Crib HOW TO DESIGN AND BUILD AN ENTRY WAY COAT RACK AND BENCH There was a door in granddad’s home the client wanted to preserve and wondered, if they provided the wood, could I build an entryway coat rack and bench using the door as part of the build. The wood they wanted to provide, well, that was from the family owned Tennessee corn crib that had been torn down and they didn’t want to lose the wood or the memories. Not only was this a corncrib but it was eventually used by the great grandchildren as a play house. So for the client there are as many memories in this build as there are colors. THIS PROJECT TRULY DEFINES THE “CUSTOM” in BAYNE CUSTOM WOODWORKING. I spent some time to design a simple layout in @sketchup_official so the client could approve the idea I had in mind. The wood showed up in two deliveries so we stacked it outside because this was the first time I worked with barn wood. I did not want to introduce possible termites to my shop. So my first call was to my pest guy asking how I would treat the wood for termites. Much to my relief he said I had nothing to worry about. This was “real” wood! Not nominal at all, nominal is how we buy our wood at a local hardware store. Where a 2×4 is actually 1 ½  x 3 ½ . These 2×4’s were at least 2”x4”’s if not more and were hard, heavy and dusty, did I say heavy? After cutting to length on my handy @DewaltTough miter saw, I had to take them to my @ridgidpowertools table saw and square up the bottoms only.  I was very careful not to lose any of the original saw marks and character because that would ruin the entire purpose. For someone who likes clean, crisp edges, this was a bit of a challenge. I used @kregjig Kreg Jig® K4 Master System to join all the pieces of the base, the seat frame and the supports to join the two together. I was very careful to hide all of the pocket holes so they could not be seen from any angle. I used Titebond Products original interior wood glue to join all the pieces together. The next item was to assemble the back which included grandad’s door as the center piece. The door was only 71 ½ tall which determined the overall height of the project. Part of this back also includes two live edge pieces that we picked to use as the “L” shaped wings or side walls. The door measured 24” which left me with 6” on each side to make up the final size of 36”. So I chose two of the straightest boards that were closest to 6” and cut them to width so as not to waste any wood or lose any character. I used the Kreg Jig® K4 Master System
Building a table is one of the most deceptively simple woodworking projects going. What could be easier than gluing up a few boards and applying a finish, right? But reality is often surprising, because building a top for that table can go wrong in ways you might not realize until it’s too late.  Here are my favourite tabletop construction tips, plus advice on how to avoid trouble.
This plan is probably the easiest plan ever added in the list. The one who is working on this project, don’t need any professional skills but just knowing some basics of woodworking will be enough for this DIY. You will get step by step detailed process of this tutorial in the source linked tutorial. This tutorial will surely help you to build this plan quickly.

There was a big crowd, rocking music, and a lot of excitement over the Extreme Post-it Notes at the 3M booth at the 2018 International Builders Show. Apparently these things stick to wood, hot stuff, cold stuff, wet stuff, brick, metal, plastic pipes, ladders, stair treads, flooring, the side of a truck, copper, tools, siding, co-workers, concrete, tile, drywall, asphalt, house wrap, light fixtures, switches, cabinets, leather belts, windows…well, you get the idea. Post-it Extreme Notes will be available at major retailers beginning in March 2018.
To corral shelf-dwelling books or DVDs that like to wander, cut 3/4-in.-thick hardwood pieces into 6-in. x 6-in. squares. Use a band saw or jigsaw to cut a slot along one edge (with the grain) that’s a smidgen wider than the shelf thickness. Stop the notch 3/4 in. from the other edge. Finish the bookend and slide it on the shelf. Want to build the shelves, too? We’ve got complete plans for great-looking shelves here.
And the fact is that you can make your own patio chair with several old but still good pallets. Here we are providing a tutorial that everybody can follow easily – it is very well-written and also self-explanatory, which is great for those who are a beginner at woodworking and have never completed a DIY project before. As you don’t need to be a professional woodworker or a handyman to complete this project, so it is not a difficult task – all you need is a bit of determination!​
Just redid my dining room table with this technique and I an observation/suggestion others might find helpful. The boards did not line up well putting it together upside down, even on a flat concrete floor with me standing on the boards while they were screwed. I would have combined biscuits with the pocket holes to ensure a better alignment of the boards. Lots of sanding was required after assembly, and this might not be a huge deal with pine, but I used hard maple so it was quite a chore even with a belt sander. Also, be aware that the 1x2s around the edge may not line up perfectly -- I had to trim about an eighth inch from each side after assembly to get nice smooth, even edges. Not a big deal, but the top turned out a little smaller than the specifications I was give by SheWhoMustBeObeyed. Otherwise our table now looks great, and thank you for the post!
×