OK, the Long Ranger’s been around since Marconi. But we love it. Simply put, this Long Ranger III Remote Dust Collector Switch is a remote system for turning on your dust collector out in the shop from whatever tool you’re operating. It plugs into the wall, you plug your dust collector into that and you’re done. Push the button on your remote and it fires right up. It’s saved us about two years and 1,300 miles of walking back and forth to the dust collector switch.

Furnishing and decorating your patio is not an easy task – but then again, it has to be done! Your patio is obviously one of the most important rooms in your home, as you can easily turn it into your little piece of Heaven, your “safe spot” in your home where you can retreat whenever you want to ignore the world and just spend some time alone all by yourself.


If you sand through the polyurethane and remove some stain, you can touch up with more stain. But the repair won’t be perfect, so take pains to avoid that mistake. Sand very lightly after the first coat, just enough to remove the dust whiskers. After the second coat, you can sand a little harder to flatten larger flaws. Always be careful around the edges of the table; that’s where it’s easiest to sand through.
PROCESSING NOTES: No matter how easy I have tried to make following these media center plans and constructing them, if you find it overwhelming to attempt the project or operate the basic tools necessary for completion, get help. Contact your local supplier to see if sheet goods can be ripped to fit your car trunk. The possibility of ordering all the parts ready for assembly is also available. Most importantly, when you set off to build your project, help is only an email message away. 

We will suggest you select the simple Birdhouse if you are new at woodworking but be sure to select its design with respect to the place where you are going to hang/place it. One of our simple Birdhouse tutorials will help you building one. We have managed to include a source tutorial below that will help you to understand illustrates and the instruction to building a simple Birdhouse.
A super simple iPad Dock/stand made out of a single block of wood features an angled groove which gets to support the tablet device and a cut in a hole to revise access to the home button of your iPad. It’s possible to drill an access channel in the stand through which you can run a charging cable, although this mini stripped back iPad stand may have very limited functions.
Currently we offer FREE FedEx/UPS small package Ground shipping and FREE ABF/YRC freight ground shipping on most orders of $49 or more within the 48 contiguous states. Some irregular shaped or oversized items may include a special handling charge. The charge will show on the product detail page of applicable products. Offer subject to change without notice.

When a fluorescent bulb goes dark, the problem can actually be one of three things: the bulb, the ballasts, or the pins. By touching the bulb with its extending wand, this niche diagnostic tool can isolate the problem. You probably don’t need one for your basement lights, but the guy who works maintenance in a 12-story office building loves this thing.
Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth. It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed.
To save money, we keep the temp in our shop down low when we’re not in it and crank up the heat when we return. But even when the air temperature hits 70 degrees F, the concrete floor is still Minnesota-cold. We tried a space heater under the bench, but it broiled the shins and still left us with cold feet. So we recently bought a foot-warming mat, and now our feet stay toasty warm. Plus, it uses a fraction of the electricity and is a lot safer than a space heater. The mat is produced by Cozy Products. The good folks over at Cozy suggest putting a chunk of cardboard underneath it if you use it on flooring that could fade from the heat, like carpet or wood.
If you want your table top -- any table top -- to actually ast without bowing/cupping/twisting, you MUST attach it in a manner that allows for seasonal wood movement. Wood is an organic product, and it naturally expands and contracts with changes in temperature and humidity. I'll post link below to a couple of options that you can cheaply buy which will allow you to securely attach a tabletop while still giving the wood the flexibility to move with the seasons. When you buy decently-made furniture at a store, they all accommodate for this one way or another. Don't just screw the top down to the legs or the skirt...you'll regret it later on.
Thermal imaging systems work great at finding water leaks, electrical hot spots, and insulation gaps in walls. But until recently, thermal imaging systems were not a practical tool for the average contractor because they cost thousands of dollars and were the size of a microwave oven. But now this extremely helpful technology is accessible. FLIR’s new C2 compact imager is pocket-size but has most of the same important features as larger models. The touch screen controls are intuitive to use, and it acts as a regular camera as well, which helps when pointing out to homeowners or coworkers where exactly the trouble spots are. They also make models that work with your smartphone.
​Luckily, we have also managed to find a detailed video tutorial of the Barn door project that illustrates the process of building a Barn door of your own. The steps and instructions in the video tutorial are different from the source links listed above. Actually, you can make different types of designs for your Barn door depending on which one you can afford easily and DIY on your own. 

No sadly, as I mentioned above, my table top ended up splitting, starting at a knot on the edge and going clear across the top (pre-drill those holes!!!), so I had to come up with another solution.  I didn’t want to go to the trouble of making another table top like this one, so I did a much easier and quicker solution…stain-grade plywood with decorative moulding attached to the edges. 
Slice, dice and serve in style on this easy, attractive board. We’ll show you a simple way to dry-fit the parts, scribe the arc and then glue the whole thing together. We used a 4-ft. steel ruler to scribe the arcs, but a yardstick or any thin board would also work. Find complete how-to instructions on this woodworking crafts project here. Also, be sure to use water-resistant wood glue and keep your board out of the dishwasher or it might fall apart. And one more thing: Keep the boards as even as possible during glue-up to minimize sanding later. For great tips on gluing wood, check out this collection.
Probably the next most useful shop accessory is a large work table. I like to use a portable table that can be moved around the shop as needed. This particular table, which you can build by clicking on the link above, is lightweight yet sturdy and has retractable casters. When you want to move the table, simply lift each end and the casters lock into place to allow the table to roll. Once you get it into position, pull the cord on each end and the casters retract, so the table won't move.
You might be able to reproduce the same concept that the table with leaves has. Instead of putting the clips on the underside of the table (since that would not allow it to lay flat over the existing table) perhaps you could get smaller hooks and place it on the underside where it overhangs on the side. Would be a little more work, but definitely cheaper than a new table. 😉
I’ve been doing a lot of remodeling on my house and this wristband has come in pretty handy. The magnets work very well and able to hold all the screws, washers, and bolts for the different projects I’m working on. The pockets are a great addition too for holding plastic items. In fact, I found it useful for holding a small pencil where I can have quick access to for marking measurements for cuts. Overall it’s a great quality wristband and would definitely recommend.
Some tools required to build a picture frame are a table saw, miter saw, measuring tape, wood glue etc. A table saw with a backing board and miter gauge can be used to get the right angle and lengths of picture frame every time. You can use builders square to arrange the final cut pieces before nailing, screwing or gluing. Check out the video tutorial below for more details.
The Milwaukee REDSTICK can be used to screed, smooth, and level. Once you’re done, the level is preposterously easy to wipe clean. The REDSTICK also has all the great features you would expect from a Milwaukee level. SHARPSITE Vial Technology makes the magnified bubble easy to read and the REDSTICK’s magnesium core keeps the level from breaking down. The Milwaukee REDSTICK Concrete Levels are available in 24-in., 48-in. and 72-in. lengths starting at $99.99.
This continuous absorption and releasing of moisture causes the wood to swell and shrink. This swelling and shrinking causes the wood to move and this movement causes issues. When it’s more humid, the moisture in the air is absorbed and the wood swells. The swelling actually has enough force to push and pull joints apart. Worse yet, if the wood is joined incorrectly it can cause the wood to crack and split.
Reclaimed Wood from Corn Crib HOW TO DESIGN AND BUILD AN ENTRY WAY COAT RACK AND BENCH There was a door in granddad’s home the client wanted to preserve and wondered, if they provided the wood, could I build an entryway coat rack and bench using the door as part of the build. The wood they wanted to provide, well, that was from the family owned Tennessee corn crib that had been torn down and they didn’t want to lose the wood or the memories. Not only was this a corncrib but it was eventually used by the great grandchildren as a play house. So for the client there are as many memories in this build as there are colors. THIS PROJECT TRULY DEFINES THE “CUSTOM” in BAYNE CUSTOM WOODWORKING. I spent some time to design a simple layout in @sketchup_official so the client could approve the idea I had in mind. The wood showed up in two deliveries so we stacked it outside because this was the first time I worked with barn wood. I did not want to introduce possible termites to my shop. So my first call was to my pest guy asking how I would treat the wood for termites. Much to my relief he said I had nothing to worry about. This was “real” wood! Not nominal at all, nominal is how we buy our wood at a local hardware store. Where a 2×4 is actually 1 ½  x 3 ½ . These 2×4’s were at least 2”x4”’s if not more and were hard, heavy and dusty, did I say heavy? After cutting to length on my handy @DewaltTough miter saw, I had to take them to my @ridgidpowertools table saw and square up the bottoms only.  I was very careful not to lose any of the original saw marks and character because that would ruin the entire purpose. For someone who likes clean, crisp edges, this was a bit of a challenge. I used @kregjig Kreg Jig® K4 Master System to join all the pieces of the base, the seat frame and the supports to join the two together. I was very careful to hide all of the pocket holes so they could not be seen from any angle. I used Titebond Products original interior wood glue to join all the pieces together. The next item was to assemble the back which included grandad’s door as the center piece. The door was only 71 ½ tall which determined the overall height of the project. Part of this back also includes two live edge pieces that we picked to use as the “L” shaped wings or side walls. The door measured 24” which left me with 6” on each side to make up the final size of 36”. So I chose two of the straightest boards that were closest to 6” and cut them to width so as not to waste any wood or lose any character. I used the Kreg Jig® K4 Master System
Angel Crafts | Baby Crafts | Basketry | Beading | Candle & Soap Making | Computer Crafts | Crochet | Knitting | Doll-Making | Drawing & Painting | Family Tree | Felt Food | Felt Flower | Floral | Gardening Crafts | Greeting Cards | Jewelry & Beading | Kids Crafts | Preschool Printables | Locker Hooking | Nail Art | Nature Crafts | Needlework | Owl Crafts | Painting | Paint Chips | Patriotic Crafts | Pennants & Buntings | Plastic Canvas | Quilting | Rubber Stamps | Scrapbooking | Sewing | Shoe Crafts | Silhouette | Soap Making | Tatting | Wedding Crafts | Woodworking
Woodworker's Supply is the expert's source for woodworking tools and hardware. We have the latest table saws, band saws, scroll saws, mortisers, jointers and planers for you to choose from. Looking for name brand cordless power tools or electric routers, router bits, and router accessories? We have a huge selection available. We represent the most respected brands on the market like Powermatic, DeWalt, Freud, Woodtek and many more. From traditional hand tools to high-tech digital measuring devices, we have what you need for the most intricate woodworking projects at woodworker.com.
Copyright 2018 by Cut The Wood. CutTheWood.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Additionally, CutTheWood.com participates in various other affiliate programs, and we sometimes get a commission through purchases made through our links.
Work at a place where you’re required to wear a steel-toe boot? Then listen up. Wolverine just introduced a new boot that’s much more comfortable but still offers solid impact protection. Instead of steel, CarbonMAX boots have a protective cap made of carbon nanotubes, making them lighter and thinner. And if anyone knows about making comfortable work boots, it’s Wolverine—they’ve been making them for more than 130 years.
With a pencil and a protractor, divide the larger disc into 30-degree wedges to create 12 center lines for the bottle indents. Center and trace the smaller disc on top of the larger disc. Next, with a drill press, drill 3/8-in.-deep holes on the 12 center lines with the 1-7/8-in. Forstner bit, spacing them between the disc’s outer edge and the traced circle. Next, divide the smaller disc into 60-degree wedges and drill six more 3/8-in.-deep holes with the Forstner bit.
The Milwaukee REDSTICK can be used to screed, smooth, and level. Once you’re done, the level is preposterously easy to wipe clean. The REDSTICK also has all the great features you would expect from a Milwaukee level. SHARPSITE Vial Technology makes the magnified bubble easy to read and the REDSTICK’s magnesium core keeps the level from breaking down. The Milwaukee REDSTICK Concrete Levels are available in 24-in., 48-in. and 72-in. lengths starting at $99.99.
The result of this project is what your wife or girlfriend would call a “Rustic,” “Barn,” or “Ranch Style” dining room table. I call it a man table, because it’s made from inexpensive wood, can take a beating, and one day your grandchildren will be serving their kids Thanksgiving dinner on it. Being the man that built that table is, well, manly. I’ve found a few similar tables on Craigslist and furniture sites, starting at around $1200. That’s absurd. I built mine for less than $200, including the chairs I bought for it.
I've worn this apron in my studio/workshop several times now, and I really like it. It's more expensive than some, but the materials and construction are first-rate. I rarely give five stars, but the workmanship on this apron is impressive. The fabric is substantial and, although a bit stiff at present, comfortable to wear. The strap and grommet system is pretty clever, allowing a good fit for most, I would think. I'm a 5'-7" not-skinny woman, and I'm able to cross the straps at the small of my back and then tie them in front, so I'm guessing there would be plenty of strap length for bigger men. The straps sit comfortably on my shoulders. And all the pockets are great!
Some moisture meters have pins that penetrate the surface of the wood. This can leave tiny holes that mar the surface and require filling. Others are pin-less. They have sensing plates that scan the wood beneath. However, not all pinless moisture meters are the same – look for one that uses technology that is not affected by the surface moisture in the wood, such as Wagner Meters IntelliSense™ Technology Moisture Meters.
No, it’s not a blood pressure tester. It’s an inflatable shim sold by Calculated industries. What in the world would you do with an Air Shim? Well, you could hold a window in position (by yourself) while setting the permanent shims, or prop up a door slab during installation without scratching the hardwood floor. Use it to align base cabinets or level appliances. You could even trick your big, burly buddy by betting him that your 10-year-old can pick him up off the ground… you will win that bet because the Air Shim is easy enough for anyone to pump and it holds up to 300-lbs. Deflate it as slow as you want for uber precision adjustments.

Are you redecorating your home but can’t seem to find the right table to complete your décor? Don’t worry too much because there are plenty of alternatives. There’s always a DIY project that can help you out. For example, we just found these beautiful DIY tables and we’re sure there are plenty more where these came from. Let’s take a look at them and see them closely.
Now, the project starts to get really interesting. While I knew that I would use pocket-hole joinery (my latest obsession) to assemble the tabletop, I couldn’t decide how to finish the wood. There were three different cans of Minwax Gel Stain on my shelf, in three different colors—Hickory, Cherrywood, and Honey Maple. In my head, I could make a credible argument in favor of each one. And though it would have helped to know where the table would eventually go, that was another question I couldn’t answer. Then it hit me: Rather than choose one stain, why not use them all? After all, I was constructing the tabletop from scraps, so it was going to have a homemade, mosaic look no matter what. In the end, using multiple stains would emphasize the rustic effect the table was going to achieve. Perfect! From there, having fought my way to a project plan, the rest came easy. Read on to see how I built the tabletop, then stained and sealed it with Minwax.
If you already have a workshop and the skills for woodworking, you will need to make sure that you have some reliable woodworking plans at your disposal and the necessary woodworking tools to complete the projects you wish to make. There are some websites that offer free woodworking plans, but they are often incomplete or lack sufficient detail to understand properly and this will lead to frustration and loss of interest in woodworking. After spending many years building up your collection of fine woodworking tools and learning to use them, you will no doubt have some neat skills under your belt. Now to make full use of these skills, you will need to find a nice project to work on, one which will do you proud and show off your fancy woodworking skills.
Breaking down heavy sheet-goods on a jobsite table saw is difficult, and dang near impossible when working alone. That’s where a track saw comes in handy. A good quality track saw can produce cabinet saw results out on any job. Now, this portable tool is even more portable. The FESTOOL TSC 55 is a cordless saw that has the same features and performs just as well as FESTOOL’s corded saw, including the cut capacity and blade speed. It also has a collection bag that actually works, collecting up to 90% of the dust. The batteries are compatible with other FESTOOL products and the saw runs on their standard tracks.
Diablo's 3 piece Adjustable Cabinet Router Bit Set Diablo's 3 piece Adjustable Cabinet Router Bit Set features a rail and stile bit set and a Double Shear raised panel bit. Featuring TiCo carbide with titanium these bits provide a long cutting life and ultra-fine finish. Perma-Shield Diablo's high performance coating reduces friction and build-up on the bits. The ...  More + Product Details Close
The next hand tool every woodworker should have is a nail set. In fact, you should have several sizes. They look like awls, and you use them to drive nail heads into the wood so they are flush or right below the surface. This allows you to fill the holes and prepare for staining or painting. The nail setter will usually have either a convex or concave surface to grip the nail better and keep it from sliding off and marring the wood.

Building a table is one of the most deceptively simple woodworking projects going. What could be easier than gluing up a few boards and applying a finish, right? But reality is often surprising, because building a top for that table can go wrong in ways you might not realize until it’s too late.  Here are my favourite tabletop construction tips, plus advice on how to avoid trouble.
×