The result of this project is what your wife or girlfriend would call a “Rustic,” “Barn,” or “Ranch Style” dining room table. I call it a man table, because it’s made from inexpensive wood, can take a beating, and one day your grandchildren will be serving their kids Thanksgiving dinner on it. Being the man that built that table is, well, manly. I’ve found a few similar tables on Craigslist and furniture sites, starting at around $1200. That’s absurd. I built mine for less than $200, including the chairs I bought for it.
With the stain dry, I began to build the tabletop. Others might have chosen to build first and stain second. But I felt that, given the combination of colors being used, I was most likely to achieve satisfying results—or less likely to mess up—if I stained the boards before I joined them together. The picture above shows the unfinished undersides of the boards after I had almost finished fastening each one to its neighbors. First, I marked off where the pocket holes would be located. For each regular board, I planned to put in at least two pocket holes. I needed to put additional holes in the boards at the two long edges, because those boards would need to be secured not only to those in the adjoining row, but also to each other. Finally, after creating the pocket holes, I assembled the tabletop one row at a time, driving in the screws that magically brought the disparate pieces together into a cohesive surface.
”Before matches became widely available in the 1860s, long, coiled wood shavings known as spills were used to transfer a flame from one location to another, such as from a fireplace to a candle, lantern or stove. Typically made using a special inverted plane, spills burn more slowly and consistently than paper, and also double as a convenient tinder material. We based the design of our spill plane on an 1850s Edward Preston spill plane in our collection.”

The Bosch Max FlexiClick 5-in-1 Drill/Driver System has one tool and five attachments. That means it can perform all kinds of tasks, like: screw-driving, drilling, right angle drilling/driving and offset driving close to edges. This tool/tools isn’t going to replace a deck builder’s 20v impact driver and drill, but it might be a great option for those smaller project that require a bunch of different operations, like knocking off a punch list at the end of a build-out. If you’re moving around and don’t have the space to haul around a bunch of dedicated tools this might be just what you’re looking for. The Bosch 5-in-1 Drill Driver System is available online and in home centers for $199.00.


Open rafters and trusses are an endless source of falling dust. So if you’re working under an open ceiling, hang plastic sheeting above. Keep the plastic at least 12 in. from light fixtures or remove the bulbs. Sometimes, adding plastic ‘walls’ is a lot easier than cleaning up the entire area. If you’re using oil-based finishes, hang the sheets about a foot from the floor to allow for ventilation.
Touch ‘n Foam’s Gel Foam Subfloor Adhesive might make you want to chuck your caulking gun for good. It comes in a can and dispenses just like the spray-foam insulation everyone is familiar with. It lays down a bead way faster than tube adhesives but without the endless, wrist-busting trigger squeezing. And you’ll be able to keep working up to 10 times longer without stopping to reload. There’s no downtime due to wet or frozen lumber, and the can is reusable up to 15 days. To use Touch ‘n Foam Subfloor Adhesive, you’ll need an applicator gun (the same one used for expanding foam). There’s also a 46-in.-long barrel for the applicator gun that will save your back from a whole lot of bending over.
Do you enjoy splinters or cuts from metal flashing? Nope me neither. THESE GLOVES ARE THE SHIZ NIT! I have yet to get a splinter when handling my rough-edged plywood. Not only are they cheap but extra reliable. Mom these gloves are for you (My poor mom always gets splinters when she helps me DIY). This is one of the unique tools you’ll be happy you own.

This super-strong and simple-to-build workbench is may be the project you've been looking for a long time. You have to select some free workbench plans to create yourself a working table in your shed that after you can use it when you are working on your projects and maybe it can provide you some extra storage, depends upon which plan you are choosing to DIY.
×