Some tools required to build a picture frame are a table saw, miter saw, measuring tape, wood glue etc. A table saw with a backing board and miter gauge can be used to get the right angle and lengths of picture frame every time. You can use builders square to arrange the final cut pieces before nailing, screwing or gluing. Check out the video tutorial below for more details.
Bought 2 of these, one for the wife and one for me. We have a project we are doing that required cutting lots of MDF(medium density fiberboard) which is not good for you to breathe or get in your eyes (very tiny particles). I picked these because people said they worked well with glasses (which i wear) and because they had full protection from flying debris and also from the airborne dust.
Oh do I need this!! I have been trying to remove the damaged veneer from a great antique table, but after many hours I think I will have to give up and try a new top. I want to make sure I understand……If I have a good base on the table, I just cut the board lengths I need and glue to the origianl table top? Do I need to secure the new top with screws from the bottom? I think the boards will give this table a whole new life. I can’t wait to finish it. Thank you so much for being here TODAY!
Creating a classic toy: One of my favorite shop projects is to create children’s cedar building blocks from rough Tennessee red cedar. These came about after I built my first Adirondack chairs and I had a large amount of scrap wood left over. Our first granddaughter had just been born and we decided to build a set of building blocks. Since that first set of blocks was made I’ve delivered hundreds to young children all across the country. Hearing the stories of the kids playing with these for hours and seeing the joy on their faces is what it’s all about. *DISCLOSURE: Some of the links below are affiliate links. If you chose to click through and make a purchase I will earn a commission but there is no additional cost to you. It helps compensates the business for the time spent creating these posts. THANK YOU! Start with Rough Cut Cedar These blocks start with rough 2×4 and 2×6 cedar lumber purchased from my local cedar mill. I use my Ridgid Power Tools Surface Planer to bring the wood into smooth milled lumber. Over to the SuperMax Drum Sander to sand the wood as much as possible. The goal is make sure the wood is as soon as glass. Then the wood goes into my Ridgid table saw to be milled into ¾ x ¾, 2 x 2 and ¾ x 2. Once the pieces are cut to proper width its over to the Grizzly Band saw to cut the blocks to length. I tried to do this on my sliding miter saw, but found I could not control the blocks well enough and the saw blade would cause them to either get jammed or fly across the shop and be ruined. Block Sizes These blocks come in a number of rectangle and square sizes. ¾ x ¾ x 2”, 4” and 6” ¾ x 2 x2’, 4” and 6” 1 ½ x1 ½ x1 ½ 2 x2 x 2”, 6” Final Step by Hand The last step is to take them to the Ridgid Oscillating Sander and round over the edges and corners to keep them safe. Because we handle them multiple times it gives is the opportunity to clear out any misfits and chipped blocks. Watch the process here. At one point we were coating them with a finish used for salad bowls but they were hard to dry without leaving ridges from the drying racks or drips that needed to be sanded off. It was recommended/suggested by a number of mothers that we not put anything on them. The beauty of these blocks is they hold the smell and are safe to play with. They provide hours of fun when stacking and building. I have watched the little ones learning how to pick things up grab and hold them. Available to purchase on Etsy Interested in having your own set? We have a limited amount available for Christmas 2018 with or without the hand made wooden
One of the best stud finders you’ll ever use is the Franklin Sensors ProSensor 710. It’s unique in that there’s a whole bar of red lights that light up whenever it detects a stud. Unlike other sensors, which have a single light that stays on as it passes over the wood, the lights on the 710 tell you exactly where the wood stops and starts. No guesswork. Push a button, drag it over the wall and those hidden mysteries reveal themselves. You won’t even need to read the directions!