This could quite possibly be the best tool on this list! Have you ever tried to get your drill in a tight spot where you absolutely had to use it and just couldn’t? Holy Moly has this happened to me like 100 times. Almost nothing is more frustrating! With this flex shaft, you can bend around corners and fit into impossibly tight spaces like a knife through hot butter! Buy this thing!!!!
Clean wooden gutters of any loose debris and cut to a manageable length. Miter down to form an approximately 40" x 94" rectangle. Coat the corners with wood glue and fasten together with 15-gauge finish nails. If miters are tight 45-degree cuts, box should be square. Double check diagonal measurements before fastening completely. The two diagonal measurements should be as close to equal as possible.
Probably the handiest shop accessory in this list would be the woodworker's bench, complete with a vise. The bench is a stable-based table with a thick, hardwood top. In the top are a series of holes that are designed to accommodate bench dogs, which are little more than pegs that can be moved from hole to hole as necessary. The end of the bench has the aforementioned vise that works in concert with the bench dogs to hold pieces steady for the woodworker.

With a pencil and a protractor, divide the larger disc into 30-degree wedges to create 12 center lines for the bottle indents. Center and trace the smaller disc on top of the larger disc. Next, with a drill press, drill 3/8-in.-deep holes on the 12 center lines with the 1-7/8-in. Forstner bit, spacing them between the disc’s outer edge and the traced circle. Next, divide the smaller disc into 60-degree wedges and drill six more 3/8-in.-deep holes with the Forstner bit.


Building a bookcase or bookshelf is a fairly simple woodworking plan that you can get done in just a day or two. This is also a low-cost project as well and since the project idea is free, you don't have to worry about busting through your budget. Just follow the simple steps in the tutorial and enjoy your own company building a simple bookcase on this weekend.
Probably the handiest shop accessory in this list would be the woodworker's bench, complete with a vise. The bench is a stable-based table with a thick, hardwood top. In the top are a series of holes that are designed to accommodate bench dogs, which are little more than pegs that can be moved from hole to hole as necessary. The end of the bench has the aforementioned vise that works in concert with the bench dogs to hold pieces steady for the woodworker.
This is another very interesting project. To make a similar table you need to have textured spray paint, matte black spray paint, lumber, wood boards, wheels, stain, sand paper, corner pieces, nails, bolts, nuts, washers, clamps and L brackets. First make the measurements and spray paint all the hardware including the wheels. Then make the basic box and sue nails to hold the wood pieces in place. Then use L brackets to keep them sturdy and add the bolts. Tighten the nuts into the bolts and attach the wheels.Then add the corner pieces sing nails{found on theblissfulbeeblog}.
A dispensing gun allows you to save foam if the job requires less than a full can. Once the job is finished, just set the gun aside until the next time you need it. Leave the can on the gun if you know it will be used in less than 30 days, or pull the can off, cap it and then clean out the gun with cleaning solution. Besides saving you money on foam, the dispensing gun provides much greater control because you’re not working with a flimsy straw, and the trigger can be adjusted with a turning setscrew to control the rate of flow—nice! Spray foam dispensing guns are available online and at home centers.
Adirondack Chairs in Tennessee Cedar Wood Growing up in Central New York and spending years in the Adirondack Mountains, I grew up seeing all types of Adirondack chairs. But it was not until I moved to middle Tennessee that I attempted to build Adirondack chairs myself. I found plans that gave me the basic design to build the adult chairs. I made some adjustments in order to fit them into my style and the type of wood that I have available. I found a cedar mill within an hour of my shop that allows me to purchase rough cut lumber. Because of the nature of rough lumber I am buying wood that is actually thicker, wider and longer than wood purchased at a brick front store.  Where a nominal 2”x 4”x 96” bought at a local lumber store is actually 1.5 x 3.5 x 96. The cedar I purchase is 2 ¼ x 4 ¼ x 102 inches. Once run through the surface planer to clean up the roughness and sanded, I am able to build with actual 2” x 4” or 2” x 6” lumber. This makes the chairs heavier, sturdier and more durable. Because of the size of the wood I assemble the legs and main supports with 3/8” carriage bolts. The arms, seat boards and backs are all assembled with 2” to 3” exterior screws. I predrill all the holes prior to inserting any screws. I do this because cedar, or any wood for that matter, can split at any time. The actual finished chair stands 38” tall x 39” long and 33” wide. They weigh about 35 lbs. and can seat a large adult very well but also comfortable for my tiny framed wife. The rise of the seat from the knees to the ground for your feet is 13 ½ inches. The seat reclines backward naturally but not so much that it is hard to stand from a seated position. The back is curved to support the natural curve of your back allowing for a more comfortable fit. The back is 32” tall to support even a taller person. The arms have been described as looking like whales so they are narrow where they fasten to the back of the chair and wide in the front for a cup, a book or even a laptop if you choose to work outside. *DISCLOSURE: Some of the links below are affiliate links. If you chose to click through and make a purchase I will earn a commission but there is no additional cost to you. It helps compensates the business for the time spent creating these posts. THANK YOU! Child’s Chair: The smaller child chairs are added to match the adult chairs to finish the family. These also are made with rough cedar milled and sanded to size to make the chairs sturdy. As with the adult chairs the wood will be thicker, wider and stronger than nominal wood. I use all true 1” lumber for the
Our favorite tools that make every project easier (and safer too!) With Black Friday soon to be upon us I wanted to put together a list of 11 items under $70.00 (it was supposed to be 10, but I couldn’t decide which to leave off!) that I use on a regular basis in my wood shop. Each of these items will make great stocking stuffers, secret Santa gifts or just something you can purchase for yourself to make your shop more efficient and safer. I have personally used all these items except the tape measure. I bought that for my son-in-law who uses it on a regular basis. I find each of these items serve multiple purposes for me in the shop to keep me safe, provide my accurate measurements and give me that extra pairs of hands that I need. You can find Amazon links below that will take you directly to the item. *DISCLOSURE: The links below are affiliate links. If you chose to click through and make a purchase I will earn a commission but there is no additional cost to you. It helps compensates the business for the time spent creating these posts. THANK YOU! SAFETY FIRST GRR-RIPPER 3D Pushblock for Table Saws, Router Tables, Band Saws, and Jointers by MICROJIG – $59.00 Safety is essential in the shop and these GRR-RIPPERS keep tablesaw blades, router bits and Jointer blades away from my fingers. No shop should be without them. I Have 2 and use them daily. 3M Peltor Optime 105 Over the Head Earmuff, Ear Protectors, Hearing Protection, NRR 30 dB $19.95 Don’t let the noise of your machinery ruin your hearing. I use these while running all the tools in my shop to protect my hearing. They fit well with safety glasses and are comfortable to wear for hours. MEASURING TOOLS Kreg KMA2900 Multi-Mark Multi-Purpose Marking and Measuring Tool Model – $42.11  Great things come in small sizes. I carry this little wonder in my apron  for every project. It helps me make sure that my wood is all the same thickness when coming out of the planer. I use it to set the depth of my dado cuts. FastCap PSSR25 25 foot Lefty/Righty Measuring Tape – $9.99 This tape measure is great for someone that has issues with the smaller measurements such as 1/8, 3/8, 5/8, etc.. Left or Right handed, this item really measures up. 12 in Centerpoint Rule – $13.95 I picked this up on a whim while walking through a wood store one day and I have never regretted it. I find it hard to determine the center point of wood at times and this finds center every time without failure and with great ease. Find the full measurement on the top of the ruler and find the same number on the bottom and that is center. NO ONE EVER HAS ENOUGH CLAMPS Large Rockler Bandy Clamps, Pair  – $24.99 I could never figure out what the fuss was for these until 

Just a little nitpick on the tape measure blurb. The hook should not be completely tight. It should move in and out about a 1/16th or the thickness of the hook. This way you get an accurate measurement whether you hook a part to measure or bump up to it. If you want more accurate measurements with a tape measure, “burn” an inch instead of hooking or bumping the part. Just line up what you want to measure with the 1″ mark and subtract that inch from the final measurement.
Personally identifying information is information that can be used to identify who you are such as: name, mailing address, email address. To enter certain areas of the site, you will be required to register and provide information about yourself. This information is for the purposes of Canadian Woodworking and helps us to tailor the site to best meet the needs of our audience. 

Most construction tasks consist of a series of straight lines, but occasionally you run into a situation that requires an arc or a circle. A trammel is usually the best tool for the job, but there’s only so much room in your toolbox. M. Power makes the Tri-Scribe, which hooks onto tools you already have, like the tongue of a square or a metal ruler, and transforms it into a flat-lying trammel. Strike a circle or an arc from 1 in. to 6 ft.—you’re limited only by the length of your rule. You can either make your mark with a pencil or insert the knife blade and score the surface. Best of all, they take up hardly any room in your toolbox.
It is becoming more popular in this DIY age for people to want to make things themselves, and we are seeing a return to woodworking as a hobby or pastime. The garage is transformed into a workshop, with a workbench a set of woodworking tools and of course a beer fridge. Beautiful handmade woodworking projects can be achieved with some practice, a good set of plans and the right woodworking tools.
Just redid my dining room table with this technique and I an observation/suggestion others might find helpful. The boards did not line up well putting it together upside down, even on a flat concrete floor with me standing on the boards while they were screwed. I would have combined biscuits with the pocket holes to ensure a better alignment of the boards. Lots of sanding was required after assembly, and this might not be a huge deal with pine, but I used hard maple so it was quite a chore even with a belt sander. Also, be aware that the 1x2s around the edge may not line up perfectly -- I had to trim about an eighth inch from each side after assembly to get nice smooth, even edges. Not a big deal, but the top turned out a little smaller than the specifications I was give by SheWhoMustBeObeyed. Otherwise our table now looks great, and thank you for the post!
Screwdrivers are another must-have in the woodworker’s set of hand tools. Not only will you need Phillips and slot, or flathead screwdrivers, you’ll need star drivers and Torx drivers, too. A quality construction is vital to a good set of screwdrivers. So many of them are made out of soft metal, and the first time you put any “oomph” behind them, they strip out, becoming absolutely useless.
These unique clamps will save you time and aggravation in too many ways to list! MatchFit clamps slide anywhere along a groove routed with a common 1/2" - 14 degree dovetail bit and leave one surface of your work clear of obstructions. Use these clamps to create customizable clamping tables and for attaching table extensions, sub fences, stop blocks, hold downs, and more to your machinery and work tables. Imported.
A super simple iPad Dock/stand made out of a single block of wood features an angled groove which gets to support the tablet device and a cut in a hole to revise access to the home button of your iPad. It’s possible to drill an access channel in the stand through which you can run a charging cable, although this mini stripped back iPad stand may have very limited functions. 

Woodworkers are a social bunch, and there are a few popular forums where people share thoughts on tools, discuss technique at length, and—of course—upload their plans. Some of the most active online woodworking communities include Lumberjocks, Woodworking Talk, Wood Magazine, WoodNet, Kreg, and Sawmill Creek. Search those to see if they have what you’re looking for (either with their built-in search tool or with Google’s site-specific search, e.g. site:lumberjocks.com side table).
A heavy-duty hardened steel chain with hexagonal links will thwart nearly every thief with a bolt cutter. Hexagonal links (or square or trapezoidal) make it impossible for bolt cutters to get a grip. You may be tempted to buy chain by the foot at the hardware store, but it’s designed for lifting and towing, not theft resistance. Even the thick stuff is likely to have round links, and frankly, if a hardware store clerk can cut the chain easily, a thief can too.
What makes this JCB Teleskid machine unique is it’s one-of-a-kind telescoping boom, which gives it the ability to reach a variety of places. The Teleskid’s telescoping boom gives you eight feet of outward reach. Plus, its one armed design gives you 60 percent more visibility than similar twin-armed machines. With a fully extended boom the Teleskid can lift up to 1600 pounds. With the boom retracted that weight capacity goes up to an impressive 3695 pounds. To find out more about the Teleskid from JCB, click here.
This is a very colorful and fun project. The idea is to use an old table with a top that you don’t really like and to give it a makeover. You don’t need paint for this project, just a lot of colored tape. Use it to make stripes to cover the entire surface of the tabletop. You can also wrap the edges in tape. You can also cover it with lacquer or add plexiglass on top to protect the design.
These tweezers are perfect. They’re nice and small and infinitely better than the cheap ones sold out of fishbowls at the home-center checkout lane. Their sharp, sturdy precision tips can grab even the tiniest sliver. Put them on your key chain and you’ll have a really high-quality stainless steel tweezers ready for the next time you have to perform a little surgery on the battlefield. They fold up like a pocketknife, so the business end doesn’t get wrecked. They’re available only at pocketweez.com.
The Wilton ATV All-Terrain Vise is a tool for those of you who work out of your pickup at job sites and need a serious on-site vise. And this vise is worth the price! It slips into any 2-in. receiver hitch and has a sizable flat anvil area for pounding. It comes with a bracket for attaching to any sturdy surface, such as a trailer, if you don’t want to use your truck.
Buying a pack of pre-organized furniture and project plans if you’re new to learning is beneficial for several reasons. Firstly, the packs of plans allow you to access a constant source of instructional content from wherever you are, whether you’re in your shop or want to browse for ideas. There are many plan sources out there and huge amounts of plans being produced and being posted online and in forums each day. By paying a small fee to take advantage of organized woodworking resources, it is easy to learn the best techniques faster and begin making projects you will use for a lifetime.
Personally identifying information is information that can be used to identify who you are such as: name, mailing address, email address. To enter certain areas of the site, you will be required to register and provide information about yourself. This information is for the purposes of Canadian Woodworking and helps us to tailor the site to best meet the needs of our audience. 
This is a well built bag that does a good job of consolidating tools. It opens up very wide and is surprisingly compact when closed. I use mine doing HVAC installation to avoid schlepping power tools one at a time. Holds a circular saw, reciprocating saw, angle grinder, hammer drill and the associated bits/discs/blades/batteries/grips. Also have a two foot level and 18" bar folder in there and it still zips closed with zero issues.

OK, the Long Ranger’s been around since Marconi. But we love it. Simply put, this Long Ranger III Remote Dust Collector Switch is a remote system for turning on your dust collector out in the shop from whatever tool you’re operating. It plugs into the wall, you plug your dust collector into that and you’re done. Push the button on your remote and it fires right up. It’s saved us about two years and 1,300 miles of walking back and forth to the dust collector switch.
Verdict : Ted’s product is EXTREMELY extensive with 16k plans and there are tons of projects to choose from. Not every woodworker online loves it, but it’s cheap and perfect for every level of experience, I love it because this is basically the only resource I need. I highly suggest it. They also offer a really solid money back guarantee if you don’t like it after all.
OK, the Long Ranger’s been around since Marconi. But we love it. Simply put, this Long Ranger III Remote Dust Collector Switch is a remote system for turning on your dust collector out in the shop from whatever tool you’re operating. It plugs into the wall, you plug your dust collector into that and you’re done. Push the button on your remote and it fires right up. It’s saved us about two years and 1,300 miles of walking back and forth to the dust collector switch.

Manufacturers that produce woodworking tools and materials have got into the content creation game, too, and some will share woodworking plans online. Minwax and Ryobi, for example, provides their plans free of charge, and Rockler offers their woodworking plans for a fee. Seek them out along with the other blogs and you’ll have a handy list of resources you can turn to for any project.
The most commonly purchased claw hammer is the 20 oz. size. It’s heavy enough to easily drive nails but easily manipulated when pulling nails. While wooden handles are picturesque, they may not stand up to the strain if you have to pull a lot of nails. Hammers with a steel handle, or even fiberglass, will be stronger. However, these won’t absorb the vibrations from driving nails the way a hickory handle will. You’ll also need to make sure the fiberglass and metal handles have a rubberized grip for control and comfort. If you’re going to be driving a lot of nails, the wooden handled hammer will be better for reducing stress on your hand, and wrist, too.
Here’s an old woodworking adage I enjoy ignoring: “measure twice, cut once.” Honestly, I measure nonce and cut thrice. I often eyeball it. I use pieces I’ve already cut to measure what I need to cut. It’s not a great habit, but I prefer it to measuring everything. And the results usually aren’t that different. At least that’s what I tell myself. I ended up having to sand down the ends of the 2×12’s running the length of the table (where they meet the aprons) because they weren’t exactly the same length.
×