Turning over the sturdy tabletop, I felt a thrill of vindication. Clearly, it wasn’t a mistake in the end to use all three stains for the same project. Before I could consider the job done, though, I would need to apply sealer—Minwax Helmsman Spar Urethane—to protect the wood from moisture, UV rays, and the wear and tear of day-to-day life. This was my first time experimenting with a spray-application sealer, and I loved it. Obviously, it’s important to have proper ventilation in your work area, and you’ve got to shake the can vigorously before spraying, but so long as you remember the basics, spraying couldn’t be more straightforward. Holding the Helmsman Spar Urethane can about a foot from the surface, spray in a series of even strokes, always in the same direction, until you’ve completed the first coat. Let the sealer dry for about four hours before applying any additional coats, and for best results, sand the entire surface before each application of a new layer.
Touch ‘n Foam’s Gel Foam Subfloor Adhesive might make you want to chuck your caulking gun for good. It comes in a can and dispenses just like the spray-foam insulation everyone is familiar with. It lays down a bead way faster than tube adhesives but without the endless, wrist-busting trigger squeezing. And you’ll be able to keep working up to 10 times longer without stopping to reload. There’s no downtime due to wet or frozen lumber, and the can is reusable up to 15 days. To use Touch ‘n Foam Subfloor Adhesive, you’ll need an applicator gun (the same one used for expanding foam). There’s also a 46-in.-long barrel for the applicator gun that will save your back from a whole lot of bending over.

Woodworkers are a social bunch, and there are a few popular forums where people share thoughts on tools, discuss technique at length, and—of course—upload their plans. Some of the most active online woodworking communities include Lumberjocks, Woodworking Talk, Wood Magazine, WoodNet, Kreg, and Sawmill Creek. Search those to see if they have what you’re looking for (either with their built-in search tool or with Google’s site-specific search, e.g. site:lumberjocks.com side table).
To save money, we keep the temp in our shop down low when we’re not in it and crank up the heat when we return. But even when the air temperature hits 70 degrees F, the concrete floor is still Minnesota-cold. We tried a space heater under the bench, but it broiled the shins and still left us with cold feet. So we recently bought a foot-warming mat, and now our feet stay toasty warm. Plus, it uses a fraction of the electricity and is a lot safer than a space heater. The mat is produced by Cozy Products. The good folks over at Cozy suggest putting a chunk of cardboard underneath it if you use it on flooring that could fade from the heat, like carpet or wood.
There’s a lot of space above the shelf in most closets. Even though it’s a little hard to reach, it’s a great place to store seldom-used items. Make use of this wasted space by adding a second shelf above the existing one. Buy enough closet shelving material to match the length of the existing shelf plus enough for two end supports and middle supports over each bracket. Twelve-inch-wide shelving is available in various lengths and finishes at home centers and lumberyards.
Some tools required to build a picture frame are a table saw, miter saw, measuring tape, wood glue etc. A table saw with a backing board and miter gauge can be used to get the right angle and lengths of picture frame every time. You can use builders square to arrange the final cut pieces before nailing, screwing or gluing. Check out the video tutorial below for more details.

Our favorite tools that make every project easier (and safer too!) With Black Friday soon to be upon us I wanted to put together a list of 11 items under $70.00 (it was supposed to be 10, but I couldn’t decide which to leave off!) that I use on a regular basis in my wood shop. Each of these items will make great stocking stuffers, secret Santa gifts or just something you can purchase for yourself to make your shop more efficient and safer. I have personally used all these items except the tape measure. I bought that for my son-in-law who uses it on a regular basis. I find each of these items serve multiple purposes for me in the shop to keep me safe, provide my accurate measurements and give me that extra pairs of hands that I need. You can find Amazon links below that will take you directly to the item. *DISCLOSURE: The links below are affiliate links. If you chose to click through and make a purchase I will earn a commission but there is no additional cost to you. It helps compensates the business for the time spent creating these posts. THANK YOU! SAFETY FIRST GRR-RIPPER 3D Pushblock for Table Saws, Router Tables, Band Saws, and Jointers by MICROJIG – $59.00 Safety is essential in the shop and these GRR-RIPPERS keep tablesaw blades, router bits and Jointer blades away from my fingers. No shop should be without them. I Have 2 and use them daily. 3M Peltor Optime 105 Over the Head Earmuff, Ear Protectors, Hearing Protection, NRR 30 dB $19.95 Don’t let the noise of your machinery ruin your hearing. I use these while running all the tools in my shop to protect my hearing. They fit well with safety glasses and are comfortable to wear for hours. MEASURING TOOLS Kreg KMA2900 Multi-Mark Multi-Purpose Marking and Measuring Tool Model – $42.11  Great things come in small sizes. I carry this little wonder in my apron  for every project. It helps me make sure that my wood is all the same thickness when coming out of the planer. I use it to set the depth of my dado cuts. FastCap PSSR25 25 foot Lefty/Righty Measuring Tape – $9.99 This tape measure is great for someone that has issues with the smaller measurements such as 1/8, 3/8, 5/8, etc.. Left or Right handed, this item really measures up. 12 in Centerpoint Rule – $13.95 I picked this up on a whim while walking through a wood store one day and I have never regretted it. I find it hard to determine the center point of wood at times and this finds center every time without failure and with great ease. Find the full measurement on the top of the ruler and find the same number on the bottom and that is center. NO ONE EVER HAS ENOUGH CLAMPS Large Rockler Bandy Clamps, Pair  – $24.99 I could never figure out what the fuss was for these until
One of the best stud finders you’ll ever use is the Franklin Sensors ProSensor 710. It’s unique in that there’s a whole bar of red lights that light up whenever it detects a stud. Unlike other sensors, which have a single light that stays on as it passes over the wood, the lights on the 710 tell you exactly where the wood stops and starts. No guesswork. Push a button, drag it over the wall and those hidden mysteries reveal themselves. You won’t even need to read the directions!
×