The end grain of wood soaks up finishes and often turns much darker than the face grain. Check for this on your test block. If you get an ugly result, pretreat the end grain with a dose of finish that will limit absorption (wood conditioner, sanding sealer, shellac or polyurethane thinned 50 percent). Apply the treatment with an artist’s brush and be careful not to slop onto the face grain.
Keep your woodworking tools and knives razor-sharp with our wide variety of sharpening supplies and accessories. We have what you need for jointer and planer knife sharpening. For sharpening plane irons and chisels, we supply a variety of diamond and waterstones, the Infinity Sandpaper Sharpening System, and honing guides. Our power sharpening systems include the Worksharp Knife Sharpeners, Ken Onion edition for the sharpest knives in the drawer.
The reclaimed wood boards are glued together, side-by-side, to form the table top. Use a biscuit joiner to cut matching slots along the board edges (Image 1). Because this tool can be set to cut the all of grooves at the same precise depth, when you insert the biscuits in the slots and pull the boards together the result is a smooth, level surface (Image 2).
Begin by cutting off a 10-in. length of the board and setting it aside. Rip the remaining 38-in. board to 6 in. wide and cut five evenly spaced saw kerfs 5/8 in. deep along one face. Crosscut the slotted board into four 9-in. pieces and glue them into a block, being careful not to slop glue into the saw kerfs (you can clean them out with a knife before the glue dries). Saw a 15-degree angle on one end and screw the plywood piece under the angled end of the block.
You can also use Google image search to research a project. Unlike the PDF search, the image search provides a photo of what the project will look like, which is helpful in determining if you want to pursue building it. By doing an image search for how to build a step stool, you will have a ton of options that all lead to woodworking plans of various quality. (The how to part of these is important—otherwise you’ll just get pictures of step stools.)
This is a very colorful and fun project. The idea is to use an old table with a top that you don’t really like and to give it a makeover. You don’t need paint for this project, just a lot of colored tape. Use it to make stripes to cover the entire surface of the tabletop. You can also wrap the edges in tape. You can also cover it with lacquer or add plexiglass on top to protect the design.
Now that you have the final dimensions for the table top, you need to choose which boards you want to use.  Because we don't have a table saw and we wanted to keep this project simple and not cut any boards lengthwise, we {and by we, I mean my husband} plugged and chugged different board sizes into his calculator to find the perfect equation. We ended up using seven 1x6 boards for the width and on the two end caps we used 1x8's. Remember, a 1x6 is not six inches wide, it's five and a half, and a 1x8 is seven and a quarter inches wide. When you are doing your math to figure out what boards you need, remember that the nominal size {1x4, 1x6, 1x8, etc} is not the actual measured dimension of the board.
Woodworkers are a social bunch, and there are a few popular forums where people share thoughts on tools, discuss technique at length, and—of course—upload their plans. Some of the most active online woodworking communities include Lumberjocks, Woodworking Talk, Wood Magazine, WoodNet, Kreg, and Sawmill Creek. Search those to see if they have what you’re looking for (either with their built-in search tool or with Google’s site-specific search, e.g. site:lumberjocks.com side table).
​Luckily, we have also managed to find a detailed video tutorial of the Barn door project that illustrates the process of building a Barn door of your own. The steps and instructions in the video tutorial are different from the source links listed above. Actually, you can make different types of designs for your Barn door depending on which one you can afford easily and DIY on your own.
Okay, let’s stain this beast. I should explain that we used Rustoleum’s Dark Walnut Ultimate Wood Stain, but we did it wrong. We failed to mix it well before applying it, resulting in a color we really liked–but not the color this stain is designed to create. When we came back to do a second coat, we stirred it well, resulting in a coat that looked like purple paint. I had to sand it off and start over. So, don’t follow my lead here–follow the can’s directions and TEST before staining all of your new masterpiece!

Everybody has a home remedy for sealing partially used tubes of caulk. But what if you had a single product that could seal caulk cartridges, squeeze tubes, glue bottles, felt-tip pens and anything else that has a nozzle? Well, these Little Red Nozzle Caps are just the ticket. Roll the cap down the nozzle to seal out dirt and preserve the remainder of the bottle, tube or cartridge.
By completing a form on this website, you will be able to receive email correspondence from Canadian Woodworking.   These emails may include information on upcoming events or special offers for subscribers. If you do not wish to receive email correspondence please email orderdesk@canadianwoodworking.com  and ask to be removed from our email list. Every email that we send to you will include an "opt-out" from receiving future email correspondence. 
Okay, let’s stain this beast. I should explain that we used Rustoleum’s Dark Walnut Ultimate Wood Stain, but we did it wrong. We failed to mix it well before applying it, resulting in a color we really liked–but not the color this stain is designed to create. When we came back to do a second coat, we stirred it well, resulting in a coat that looked like purple paint. I had to sand it off and start over. So, don’t follow my lead here–follow the can’s directions and TEST before staining all of your new masterpiece!

Breaking down heavy sheet-goods on a jobsite table saw is difficult, and dang near impossible when working alone. That’s where a track saw comes in handy. A good quality track saw can produce cabinet saw results out on any job. Now, this portable tool is even more portable. The FESTOOL TSC 55 is a cordless saw that has the same features and performs just as well as FESTOOL’s corded saw, including the cut capacity and blade speed. It also has a collection bag that actually works, collecting up to 90% of the dust. The batteries are compatible with other FESTOOL products and the saw runs on their standard tracks.
If you already have a workshop and the skills for woodworking, you will need to make sure that you have some reliable woodworking plans at your disposal and the necessary woodworking tools to complete the projects you wish to make. There are some websites that offer free woodworking plans, but they are often incomplete or lack sufficient detail to understand properly and this will lead to frustration and loss of interest in woodworking. After spending many years building up your collection of fine woodworking tools and learning to use them, you will no doubt have some neat skills under your belt. Now to make full use of these skills, you will need to find a nice project to work on, one which will do you proud and show off your fancy woodworking skills.
Online plans can be easy, helpful, and can save you time and money if you put in the effort to usethem. But if you buy plans one by one, you might speed a lot of time organizing and searching for things to build as well as having to decipher different plan formats. You might learn a technique or two or improve your skills slightly, but you’ll forget everything by the time you go to find another plan. With organized lessons, however, you can always find the plans or instructions again easily, and come up with even more ideas of projects to build. Downloadable woodworking courses can save you money as well.
Check out our most recent woodworking tools and accessory reviews below. We have thousands of satisfied customers that use our router bits, shaper cutters, router tables, and many more fine woodworking tools every day. Take a minute to read what your fellow woodworkers have to say about their experience with our company and our quality woodworking tools. All reviews are from real customers of Infinity Tools who were polled by our partners at ShopperApproved.com. More third party reviews can be found at Shopper Approved's website.
This time I surprised one of my favorite dice games and took it outside. I made a set of wooden dice in just a few hours, and instead of sitting in the room and doing nothing, we are taking our dice game out into the yard. With this set of wooden dice, dice games are becoming our favorite backyard game. Check out the step by step tutorial below so you can make your own.
It’s important to have an understanding of wood when building DIY furniture projects. Not just how to cut, and assemble with wood but also to understand how it works. In Mistakes with Wood Can Cause Your DIY Furniture to Crack we talked about how wood is hygroscopic. Simply put, hygroscopic means it absorbs moisture from the air. Seasonal changes cause wood to absorb and release moisture. 

Attach all four legs and set the top on the base with equal overhang on all sides. Carefully trace the leg tops on the bottom side of the planks and then flip it over onto a work surface. Drill a 1/2” hole with each square mark near the line but not touching it. Using a jigsaw, carefully cut out each square. Because leg tops will nest snuggly in these squares, be sure cuts are slightly undersized. Flip the top back over and attempt to set it on the base. Using a flat wood file and chisel, remove small amounts of material as needed. Once the top nestles down on the gutter structure without excess force, run a small bead of wood glue on the top edges of the gutter, reposition the top and shoot 15-gauge finish nails through the inside edge of the gutter into the bottom of the tabletop. Fill in small gaps between the leg top and table planks with wood filler or small wood shims.

If you want your table top -- any table top -- to actually ast without bowing/cupping/twisting, you MUST attach it in a manner that allows for seasonal wood movement. Wood is an organic product, and it naturally expands and contracts with changes in temperature and humidity. I'll post link below to a couple of options that you can cheaply buy which will allow you to securely attach a tabletop while still giving the wood the flexibility to move with the seasons. When you buy decently-made furniture at a store, they all accommodate for this one way or another. Don't just screw the top down to the legs or the skirt...you'll regret it later on.


This set of tools have helped a lot in my startup of woodworking. I'm an amateur, and these bars really helped me out. These have come to be very useful in my recent project, where I'm trying to build a kitchen open faced cabinet, and I needed to cut some dado's and these have helped quite a bit. I also used them to help set up my table saw to the correct height of he blade, to accurately cut slots by measuring the height of the blade for the slot cuts in my drawers. I've tried using rulers, but one needs 4 hands to make all the correct measurements. These cut out the other 2 set of hands.
Your moisture meter should have settings on it that will account for different species of wood. For instance, oak is a hardwood, but ebony is an even harder density wood. If you are planning an inlay job using both types of wood, you will need to know the moisture content levels of each of the two species so that your inlay glue joints will stay intact. These different wood species have different specific gravities, which must be used or programmed into the moisture meter.
For this project you need a table base. An old table with no top would be perfect. The idea is to create a new wood top with an original design. Since this project is for an outdoor table, you can also include an ice bucket in the middle. Find some large pieces of wood and put them together to make a top. Make a hole for the bucket if you want one and insert it. Then, to make the edges of the table, use a belt sander. Get creative until you’re happy with the results and, at the end, stain the table.{found on thehuntedinterior}.
You can also use Google image search to research a project. Unlike the PDF search, the image search provides a photo of what the project will look like, which is helpful in determining if you want to pursue building it. By doing an image search for how to build a step stool, you will have a ton of options that all lead to woodworking plans of various quality. (The how to part of these is important—otherwise you’ll just get pictures of step stools.)
When it comes to choosing a finish there are two main choices. The typical approach of stain and urethane creates a smooth, wipeable surface, but when that finish eventually wears through, there’s no way of repairing it attractively. Sanding back to bare wood and refinishing is the only way to make it respectable again. Oil and wax finishes, on the other hand, take more time to apply initially, but they’re easily repaired and rejuvenated with the tabletop in place. Regular reapplication works just fine.
There’s a lot of space above the shelf in most closets. Even though it’s a little hard to reach, it’s a great place to store seldom-used items. Make use of this wasted space by adding a second shelf above the existing one. Buy enough closet shelving material to match the length of the existing shelf plus enough for two end supports and middle supports over each bracket. Twelve-inch-wide shelving is available in various lengths and finishes at home centers and lumberyards.
An assortment of chisels should be part of every workbench. Chisels are not just for wood carvers. Any woodworker will need chisels to clean out joints and saw cuts. Look for chisels made of high-alloy carbon steel or chromium-vanadium alloyed steel. Hardwood grips are best, especially if they have metal caps on them. This will keep the end of the handle from becoming malformed when you hammer on it.
After sanding, I wiped down the table to remove any dust. Then I stirred the polyurethane and brushed it on the table top, including all four sides. After the polyurethane coating dried, the table was ready to be used. I used the poly coat because the table is being used on an outdoor porch. It is a covered porch, but sometimes there is a blowing rain. I also wanted a protective coating because the table is being used for food and drinks. I didn’t want to worry about anything being spilled on the table.
Every carpenter or woodworker has needed a pair of sawhorses at some point. I've used them for hundreds of tasks, including as a sturdy base for a table saw. This set of saw horses is stackable, very solid (they will hold as much as 500 pounds each if properly built) and very easy and inexpensive to build. Once you have a set, you'll find hundreds of uses for them, not only in the wood shop but around the house as well.

Drilling into tile is sort of a three hand operation: hold the drill, spray the water, and make sure the water stays were it’s supposed to. The Aqua Shot from Miyanaga is a great solution to your ceramic drilling woes. The Aqua Shot drill bit has a built-in water tank that feeds water to the drill as you operate, making the whole process much smoother. Just load the chamber up with water, flip a switch and drill away. The Aqua Shot works with impact drivers and the individual tips can be replaced when they get worn out without having to replace the whole tool. The Aqua Shot is available online for $82.80. Click here for a video of the Aqua Shot in action.
By video tutorial, you will get step by step process instructions of making a nice wooden folding sling chair from scratch. However, my first wooden chair was not the best one, but it was good enough to motivate me to make some more folding chairs like this one. If I can make this, you too can make one yourself. You can browse the internet for more folding sling chairs ideas and start making one now.
I had been looking forward to this part—applying the Minwax Gel Stain. First, I tested the stains on a leftover board to confirm my suspicion that, used together, the three stains would complement one another perfectly. When the test confirmed my suspicions, I proceeded to stir each stain until it developed a creamy, smooth consistency—nothing like the watery liquid you might be used to. With its thicker formulation, Minwax Gel Stain has been specially designed to be user-friendly and easy to apply. With either a foam brush or a rag, the Gel Stain goes on in a controlled way, and you don’t have to worry about drips; just let it sit on the wood for about three minutes and wipe away the excess with a rag. Once I had finished staining all the wood pieces in alternating colors—Hickory, Cherrywood, and Honey Maple—I let about eight hours of dry time elapse. Though it wasn’t strictly necessary, I decided to darken the stain colors a bit by applying a second coat, using the same technique I’d used with the first.

A super simple iPad Dock/stand made out of a single block of wood features an angled groove which gets to support the tablet device and a cut in a hole to revise access to the home button of your iPad. It’s possible to drill an access channel in the stand through which you can run a charging cable, although this mini stripped back iPad stand may have very limited functions.


This is a well built bag that does a good job of consolidating tools. It opens up very wide and is surprisingly compact when closed. I use mine doing HVAC installation to avoid schlepping power tools one at a time. Holds a circular saw, reciprocating saw, angle grinder, hammer drill and the associated bits/discs/blades/batteries/grips. Also have a two foot level and 18" bar folder in there and it still zips closed with zero issues.
The next important hand tool for the woodworker is an accurate tape measure. Get a retractable one that is at least 25 feet long. Any longer than that, and you start having problems getting it to roll back up. Since measurements on large scale projects can be very susceptible to even the most minute measurement variations, you’ll want to make sure the “hook” or tab at the end of the is firmly attached, with no give. When they get loose, you’ll have as much as 1/8” variation in your measurements. This can add up to some severe accuracy problems in the long run.
Currently we offer FREE FedEx/UPS small package Ground shipping and FREE ABF/YRC freight ground shipping on most orders of $49 or more within the 48 contiguous states. Some irregular shaped or oversized items may include a special handling charge. The charge will show on the product detail page of applicable products. Offer subject to change without notice.

Today I want to show you a project that’s within your reach if you have a few tools, a couple weekends, and the courage to take on something new. If you’re completely new to woodworking, this may be a little ambitious, but if you’ve got a little experience, you shouldn’t encounter too much trouble. Keep in mind that I’m an amateur. I took shop class in high school and have done a few little projects here and there, but I’m certainly no pro.

Carefully lay the top down and attach pipe clamps at roughly 1' intervals. Slowly tighten each pipe clamp in a consistent fashion until the gaps disappear. Small amounts of glue can be removed when dry; scrape up any puddled glue with a plastic putty knife. To minimize sanding later, avoid working glue into the top of the wood. Let the top set overnight.

Rachel Teodoro and Holy-Craft.com, 2010-present. Unauthorized use and/or duplication of this material without express and written permission from this site’s author and/or owner is strictly prohibited. Excerpts and links may be used and up to one photo can posted, provided that full and clear credit is given to Rachel Teodoro and Holy Craft with appropriate and specific direction to the original content.


I've worn this apron in my studio/workshop several times now, and I really like it. It's more expensive than some, but the materials and construction are first-rate. I rarely give five stars, but the workmanship on this apron is impressive. The fabric is substantial and, although a bit stiff at present, comfortable to wear. The strap and grommet system is pretty clever, allowing a good fit for most, I would think. I'm a 5'-7" not-skinny woman, and I'm able to cross the straps at the small of my back and then tie them in front, so I'm guessing there would be plenty of strap length for bigger men. The straps sit comfortably on my shoulders. And all the pockets are great!

The best thing about the toy chest is that it is very easy to build. All you need is the basic understanding of woodworking and a few tools to get started. You can also modify your kid’s toy chest in any way you want or build in a different design or color different from the one pictured above. You can try some other designs for your plan in the below-mentioned link.

I've worn this apron in my studio/workshop several times now, and I really like it. It's more expensive than some, but the materials and construction are first-rate. I rarely give five stars, but the workmanship on this apron is impressive. The fabric is substantial and, although a bit stiff at present, comfortable to wear. The strap and grommet system is pretty clever, allowing a good fit for most, I would think. I'm a 5'-7" not-skinny woman, and I'm able to cross the straps at the small of my back and then tie them in front, so I'm guessing there would be plenty of strap length for bigger men. The straps sit comfortably on my shoulders. And all the pockets are great!
Im am so glad you posted this! I bought a cheap dining room table from good will to use for my desk, it has a leaf in the middle to make it longer. I wanted to glue the leaf to the other two sides and thin fill in the holes with wood filler and I was advised by mom friend that it wouldnt work, but now I have proof cant wait to try it out!!! thanks 🙂
I am so glad to see this. It is exactly what I have been looking for. I have had a similar idea in my head for years but didn't know how to bring it together, and I wasn't sure how it would actually turn out. Yours is beautiful. It is nice to start with an idea of how the project will actually look when I am done. My table is 25 years old with a laminate top. The reason I want to cover instead of replacing it does that it is the first purchase my husband and I made together. It has seen 25 years of abuse by three little (now big!) boys and by me, the messy crafter. But I cannot imagine ever getting rid of this table. Plus it's not like I'm going to get less messy, so investing in an expensive table would be crazy. I love how I can take this top off and still do the messy damaging things on it. I am bookmarking this and if I ever get around to actually doing it LOL, I will send you pics
She has permanently glued and screwed the tabletop within that four-sided, mitered frame. Attaching the skirt to the long edges of the wide boards is no problem, but fastening them to the end grain of the wide boards, as shown in the photo above, is. The builder has constricted the wide boards' movement, and as they grow or shrink in width but are held in place by those end-caps, they will warp and split, making this a short-lived piece of furniture.
Now that you have the tools, you can build anything you want whenever you want at a fraction of the cost. Install molding, update your window casings and trimwork, build a custom closet, some laundry room shelves or whatever! Not to mention, now you can start making gifts for friends and family or building a small business. The opportunities are set by your imagination.
If you want your table top -- any table top -- to actually ast without bowing/cupping/twisting, you MUST attach it in a manner that allows for seasonal wood movement. Wood is an organic product, and it naturally expands and contracts with changes in temperature and humidity. I'll post link below to a couple of options that you can cheaply buy which will allow you to securely attach a tabletop while still giving the wood the flexibility to move with the seasons. When you buy decently-made furniture at a store, they all accommodate for this one way or another. Don't just screw the top down to the legs or the skirt...you'll regret it later on.
If you’re like me, every time you wander through a big-box furniture store, you feel a little insulted. Here you are, a man, staring at relatively simple furniture, being asked to lay down large sums of money for a bookshelf, dining set, or desk. And if you know enough about wood to spot laminate and fiberboard, you’ll quickly see these expensive pieces of furniture have a shelf life (no pun intended) of about two years.
Breaking down heavy sheet-goods on a jobsite table saw is difficult, and dang near impossible when working alone. That’s where a track saw comes in handy. A good quality track saw can produce cabinet saw results out on any job. Now, this portable tool is even more portable. The FESTOOL TSC 55 is a cordless saw that has the same features and performs just as well as FESTOOL’s corded saw, including the cut capacity and blade speed. It also has a collection bag that actually works, collecting up to 90% of the dust. The batteries are compatible with other FESTOOL products and the saw runs on their standard tracks.
While the top is drying, measure the thickest portion. Add 1/16” to this measurement and mark a horizontal line with a framing square across the tops of the table legs. This line marks the gutter structure mounting depth. Legs will protrude 1/16” above the plane of the tabletop. Ask a helper to hold the leg tight to the inside corner of the gutter structure with the mark at the top of the gutter. Drive at least two wood screws through the inside face of the gutter into the sides of the leg.
The client then explains the furniture he wants. In detail, he describes the dimensions, moving parts, the features of the furniture and his budget for such work. The woodworker takes note of the information and gives the client an estimate. After a day or two, the woodworker gives a preliminary design of the item the customer wishes to have. The design could be revised if the customer wishes to alter it. The first exchange of money, the payment of the design fee, usually happens here.
Keep your woodworking tools and knives razor-sharp with our wide variety of sharpening supplies and accessories. We have what you need for jointer and planer knife sharpening. For sharpening plane irons and chisels, we supply a variety of diamond and waterstones, the Infinity Sandpaper Sharpening System, and honing guides. Our power sharpening systems include the Worksharp Knife Sharpeners, Ken Onion edition for the sharpest knives in the drawer.

Let’s start with perhaps the most basic tool in every household – the claw hammer. The claw on one side of the head should be well counterbalanced by the finished head, which should be somewhat rounded. The other kind of head is the waffle-head. Most commonly used in construction, it leaves a distinctive waffle mark on the wood when you drive the nail. This, of course, is not the proper nail for woodworking.
Leave your tabletop longer than necessary until the sanding is done, then cut to final length. Most tabletops are too wide to trim on a tablesaw, even with a crosscut sled, and this is where I use a hand-held circular saw. Clamp a guide strip so it’s square to one edge, then follow it with your saw. Repeat the process on the other end, then carefully use your hand-held belt sander to remove any blade marks on edges. It sounds like a coarse process, but you can get great results this way.
Woodworking plans for difficult projects, will list which tools you need to use and show you the areas where you still need practice. Come back to the advanced woodworking plan later on, after you have had more practice with your woodworking tools doing basic projects which steadily build your skill level. To gain the skills for advanced woodworking, you really need to try as much variety as possible, so that you broaden your experience. Making 100 coffee tables that are all the same will not make you a skilled woodworker but making 100 different tables of all kinds and sizes, will certainly make you a skilled woodworker.
Begin by cutting off a 10-in. length of the board and setting it aside. Rip the remaining 38-in. board to 6 in. wide and cut five evenly spaced saw kerfs 5/8 in. deep along one face. Crosscut the slotted board into four 9-in. pieces and glue them into a block, being careful not to slop glue into the saw kerfs (you can clean them out with a knife before the glue dries). Saw a 15-degree angle on one end and screw the plywood piece under the angled end of the block.
×