You would think that a sharp tool you swing in the direction of your ankles wouldn't last long. But the adze can be traced back at least to ancient Egypt. You use the adze to shape tree trunks and square them up into beams; looks like an ax with the blade oriented on the horizontal. But with modern-day milling capabilities so much faster and easier, for the most part the adze has gone the way of the dodo.

After all slots are cut, stand each board on end and coat the edge of jointed side with wood glue. Next coat the biscuits with glue. Insert biscuits in one side only of each board, then insert glued biscuits in the empty joint of the next board. Assemble planks in order until the top is complete. Don't worry about small gaps. Next, carefully lay the top down and attach pipe clamps at roughly 1' intervals. Slowly tighten each pipe clamp in a consistent fashion until the gaps disappear*. Small amounts of glue can be removed when dry; scrape up any puddled glue with a plastic putty knife. To minimize sanding later, avoid working glue into the top of the wood. Let the top set overnight.


Be sure wood is dry. Material from a job site or floor joists that existed in a crawlspace may have high moisture content; material from a conditioned space should be dry. Wood can be dried in a kiln (ask your local lumber mill) or stored inside through the winter. If time does not permit, stack wood in a hot dry place with 1" spacers between layers. Allow to dry for a minimum of two weeks.
The Bosch Max FlexiClick 5-in-1 Drill/Driver System has one tool and five attachments. That means it can perform all kinds of tasks, like: screw-driving, drilling, right angle drilling/driving and offset driving close to edges. This tool/tools isn’t going to replace a deck builder’s 20v impact driver and drill, but it might be a great option for those smaller project that require a bunch of different operations, like knocking off a punch list at the end of a build-out. If you’re moving around and don’t have the space to haul around a bunch of dedicated tools this might be just what you’re looking for. The Bosch 5-in-1 Drill Driver System is available online and in home centers for $199.00.
A trusty pair of Electrician Scissors is the most used tool of many of the low-voltage electricians that we’ve talked to, and Klein seems to be the go-to brand. If you’ve never heard of electrician scissors, here is a primer: Of course like any scissors, Klein’s new Electrician Scissors can cut through stuff with the blades, but they also have a cable cutting notch so you can rip through wire up to 14 AWG. They’ll strip 19 and 23 AWG wire all day long and have a notch in the tip for de-burring electrical boxes. There’s also a scraper on both blades for convenient wire cleaning. Klein’s All-Purpose Electrician’s Scissors are available online and in home centers for $24.35.
Are you redecorating your home but can’t seem to find the right table to complete your décor? Don’t worry too much because there are plenty of alternatives. There’s always a DIY project that can help you out. For example, we just found these beautiful DIY tables and we’re sure there are plenty more where these came from. Let’s take a look at them and see them closely.
Reclaimed Wood from Corn Crib HOW TO DESIGN AND BUILD AN ENTRY WAY COAT RACK AND BENCH There was a door in granddad’s home the client wanted to preserve and wondered, if they provided the wood, could I build an entryway coat rack and bench using the door as part of the build. The wood they wanted to provide, well, that was from the family owned Tennessee corn crib that had been torn down and they didn’t want to lose the wood or the memories. Not only was this a corncrib but it was eventually used by the great grandchildren as a play house. So for the client there are as many memories in this build as there are colors. THIS PROJECT TRULY DEFINES THE “CUSTOM” in BAYNE CUSTOM WOODWORKING. I spent some time to design a simple layout in @sketchup_official so the client could approve the idea I had in mind. The wood showed up in two deliveries so we stacked it outside because this was the first time I worked with barn wood. I did not want to introduce possible termites to my shop. So my first call was to my pest guy asking how I would treat the wood for termites. Much to my relief he said I had nothing to worry about. This was “real” wood! Not nominal at all, nominal is how we buy our wood at a local hardware store. Where a 2×4 is actually 1 ½  x 3 ½ . These 2×4’s were at least 2”x4”’s if not more and were hard, heavy and dusty, did I say heavy? After cutting to length on my handy @DewaltTough miter saw, I had to take them to my @ridgidpowertools table saw and square up the bottoms only.  I was very careful not to lose any of the original saw marks and character because that would ruin the entire purpose. For someone who likes clean, crisp edges, this was a bit of a challenge. I used @kregjig Kreg Jig® K4 Master System to join all the pieces of the base, the seat frame and the supports to join the two together. I was very careful to hide all of the pocket holes so they could not be seen from any angle. I used Titebond Products original interior wood glue to join all the pieces together. The next item was to assemble the back which included grandad’s door as the center piece. The door was only 71 ½ tall which determined the overall height of the project. Part of this back also includes two live edge pieces that we picked to use as the “L” shaped wings or side walls. The door measured 24” which left me with 6” on each side to make up the final size of 36”. So I chose two of the straightest boards that were closest to 6” and cut them to width so as not to waste any wood or lose any character. I used the Kreg Jig® K4 Master System

There is no cost to use the database. Registering is not required. You should be able to browse the database and click through the links. Having said that, considering the fact there are so many browsers out there being used, this site's software might not allow some visitors to browse, it all depends on the Internet traffic, and your browser's compatibility.
Oh do I need this!! I have been trying to remove the damaged veneer from a great antique table, but after many hours I think I will have to give up and try a new top. I want to make sure I understand……If I have a good base on the table, I just cut the board lengths I need and glue to the origianl table top? Do I need to secure the new top with screws from the bottom? I think the boards will give this table a whole new life. I can’t wait to finish it. Thank you so much for being here TODAY!
A magnetized screwdriver or driver bit makes starting screws a lot easier. It’s like having an extra hand to hold the screw. We also like to magnetize a screwdriver when working with tiny screws that are nearly impossible to find if you drop them (been there?). You can use a magnetic bit holder in most cases, but not in tight quarters. Instead, you can just magnetize the bit. We’ve even magnetized tweezers to help pick up tiny parts.
When sourcing materials from a renovation or job site be sure to have clear permission and wear the appropriate safety gear. Be aware that lead paint and asbestos may be mixed in with clean wood. Watch out for and pull nails out of material before loading in a car or truck so reclaimed wood will stack better. Be careful when working with items painted prior to 1979 as they may contain lead-based paint. Be sure to consult the EPA's Renovate Right: Important Lead Hazard Information for Families, Child Care Providers, and Schools pamphlet before disturbing any paint that could contain lead. Building materials produced before 1983 should also generally be tested for asbestos. Contact your local building official for exact requirements.
This time I surprised one of my favorite dice games and took it outside. I made a set of wooden dice in just a few hours, and instead of sitting in the room and doing nothing, we are taking our dice game out into the yard. With this set of wooden dice, dice games are becoming our favorite backyard game. Check out the step by step tutorial below so you can make your own.
Although it’s tempting to use a random orbit sander to smooth your table top at the final stages, I never do. Finish quality is the reason why. Random orbit sanders often leave behind swirl marks that don’t show up until finishing time. A better option is to complete the sanding process by hand, using 180-, then 220-grit paper only in the direction of wood grain. The finish of a tabletop is more closely examined than wood finishes anywhere else, so you need to eliminate all flaws.
By posting on this site and forum, the poster grants to Canadian Woodworking Magazine/Website the unrestricted rights to use of the content of the post for any purpose, including, but not limited to, publishing the posted material, including images, in print or electronic form in a future issue or issues of Canadian Woodworking magazine or related Canadian Woodworking products, and to use the post for promotional purposes without further compensation, as well as the right to use the poster's name in a credit along with the post. 

There’s a lot of space above the shelf in most closets. Even though it’s a little hard to reach, it’s a great place to store seldom-used items. Make use of this wasted space by adding a second shelf above the existing one. Buy enough closet shelving material to match the length of the existing shelf plus enough for two end supports and middle supports over each bracket. Twelve-inch-wide shelving is available in various lengths and finishes at home centers and lumberyards.
Now that you have the final dimensions for the table top, you need to choose which boards you want to use.  Because we don't have a table saw and we wanted to keep this project simple and not cut any boards lengthwise, we {and by we, I mean my husband} plugged and chugged different board sizes into his calculator to find the perfect equation. We ended up using seven 1x6 boards for the width and on the two end caps we used 1x8's. Remember, a 1x6 is not six inches wide, it's five and a half, and a 1x8 is seven and a quarter inches wide. When you are doing your math to figure out what boards you need, remember that the nominal size {1x4, 1x6, 1x8, etc} is not the actual measured dimension of the board.
After your table is pieced together, you will flip it over {remember, you've been working on it upside down} and sand it.  My husband isn't a big fan of the planks and worried about cups and plates getting stuck and spilled on the uneven parts of the boards, so he went to town with the sander. You can keep more of the plank look by sanding it less.

It’s important to have an understanding of wood when building DIY furniture projects. Not just how to cut, and assemble with wood but also to understand how it works. In Mistakes with Wood Can Cause Your DIY Furniture to Crack we talked about how wood is hygroscopic. Simply put, hygroscopic means it absorbs moisture from the air. Seasonal changes cause wood to absorb and release moisture.


For an artisanal look, you can use woodworking hand tools. These are easy to use, lightweight and require no batteries or power cords to operate. Many hand tools are covered by multi-year or even lifetime warranties for extra protection and value. Set up your pieces with the most expertly crafted woodworking hardware, such as hinges, pulls and knobs to create a final product that you can give as a gift, sell or just display proudly.
I purchased these gloves for work, which involves handling and packing several (thousand) books everyday. When they arrived, they were a little too big for my smallish hands. I figured I would use them anyway to spare my sore fingers, and for the week I used these my hands were safe and papercut-free! The grip dots were secure and helped to grip even thin sheets of paper. The fingers bunched up a bit, but that's to be expected from oversized gloves.
What makes this JCB Teleskid machine unique is it’s one-of-a-kind telescoping boom, which gives it the ability to reach a variety of places. The Teleskid’s telescoping boom gives you eight feet of outward reach. Plus, its one armed design gives you 60 percent more visibility than similar twin-armed machines. With a fully extended boom the Teleskid can lift up to 1600 pounds. With the boom retracted that weight capacity goes up to an impressive 3695 pounds. To find out more about the Teleskid from JCB, click here. 

A magnetized screwdriver or driver bit makes starting screws a lot easier. It’s like having an extra hand to hold the screw. We also like to magnetize a screwdriver when working with tiny screws that are nearly impossible to find if you drop them (been there?). You can use a magnetic bit holder in most cases, but not in tight quarters. Instead, you can just magnetize the bit. We’ve even magnetized tweezers to help pick up tiny parts.
Building a table is one of the most deceptively simple woodworking projects going. What could be easier than gluing up a few boards and applying a finish, right? But reality is often surprising, because building a top for that table can go wrong in ways you might not realize until it’s too late.  Here are my favourite tabletop construction tips, plus advice on how to avoid trouble.
×