No sadly, as I mentioned above, my table top ended up splitting, starting at a knot on the edge and going clear across the top (pre-drill those holes!!!), so I had to come up with another solution.  I didn’t want to go to the trouble of making another table top like this one, so I did a much easier and quicker solution…stain-grade plywood with decorative moulding attached to the edges. 

This was not actually a tutorial post to the woodworking plan ideas but the aim of the post was to give some easy and free woodworking ideas to the readers. If you have some time to entertain yourself and also willing to add some new stuff to your furniture you can take any idea from the list and start working on it. Be sure to see both post tutorial and video tutorials of the plan you have selected, it will make you understand everything nicely.


Reclaimed Wood from Corn Crib HOW TO DESIGN AND BUILD AN ENTRY WAY COAT RACK AND BENCH There was a door in granddad’s home the client wanted to preserve and wondered, if they provided the wood, could I build an entryway coat rack and bench using the door as part of the build. The wood they wanted to provide, well, that was from the family owned Tennessee corn crib that had been torn down and they didn’t want to lose the wood or the memories. Not only was this a corncrib but it was eventually used by the great grandchildren as a play house. So for the client there are as many memories in this build as there are colors. THIS PROJECT TRULY DEFINES THE “CUSTOM” in BAYNE CUSTOM WOODWORKING. I spent some time to design a simple layout in @sketchup_official so the client could approve the idea I had in mind. The wood showed up in two deliveries so we stacked it outside because this was the first time I worked with barn wood. I did not want to introduce possible termites to my shop. So my first call was to my pest guy asking how I would treat the wood for termites. Much to my relief he said I had nothing to worry about. This was “real” wood! Not nominal at all, nominal is how we buy our wood at a local hardware store. Where a 2×4 is actually 1 ½  x 3 ½ . These 2×4’s were at least 2”x4”’s if not more and were hard, heavy and dusty, did I say heavy? After cutting to length on my handy @DewaltTough miter saw, I had to take them to my @ridgidpowertools table saw and square up the bottoms only.  I was very careful not to lose any of the original saw marks and character because that would ruin the entire purpose. For someone who likes clean, crisp edges, this was a bit of a challenge. I used @kregjig Kreg Jig® K4 Master System to join all the pieces of the base, the seat frame and the supports to join the two together. I was very careful to hide all of the pocket holes so they could not be seen from any angle. I used Titebond Products original interior wood glue to join all the pieces together. The next item was to assemble the back which included grandad’s door as the center piece. The door was only 71 ½ tall which determined the overall height of the project. Part of this back also includes two live edge pieces that we picked to use as the “L” shaped wings or side walls. The door measured 24” which left me with 6” on each side to make up the final size of 36”. So I chose two of the straightest boards that were closest to 6” and cut them to width so as not to waste any wood or lose any character. I used the Kreg Jig® K4 Master System
This super-strong and simple-to-build workbench is may be the project you've been looking for a long time. You have to select some free workbench plans to create yourself a working table in your shed that after you can use it when you are working on your projects and maybe it can provide you some extra storage, depends upon which plan you are choosing to DIY.
When it comes to choosing a finish there are two main choices. The typical approach of stain and urethane creates a smooth, wipeable surface, but when that finish eventually wears through, there’s no way of repairing it attractively. Sanding back to bare wood and refinishing is the only way to make it respectable again. Oil and wax finishes, on the other hand, take more time to apply initially, but they’re easily repaired and rejuvenated with the tabletop in place. Regular reapplication works just fine.

I’ve been doing a lot of remodeling on my house and this wristband has come in pretty handy. The magnets work very well and able to hold all the screws, washers, and bolts for the different projects I’m working on. The pockets are a great addition too for holding plastic items. In fact, I found it useful for holding a small pencil where I can have quick access to for marking measurements for cuts. Overall it’s a great quality wristband and would definitely recommend.


No, it’s not a blood pressure tester. It’s an inflatable shim sold by Calculated industries. What in the world would you do with an Air Shim? Well, you could hold a window in position (by yourself) while setting the permanent shims, or prop up a door slab during installation without scratching the hardwood floor. Use it to align base cabinets or level appliances. You could even trick your big, burly buddy by betting him that your 10-year-old can pick him up off the ground… you will win that bet because the Air Shim is easy enough for anyone to pump and it holds up to 300-lbs. Deflate it as slow as you want for uber precision adjustments.
Furnishing and decorating your patio is not an easy task – but then again, it has to be done! Your patio is obviously one of the most important rooms in your home, as you can easily turn it into your little piece of Heaven, your “safe spot” in your home where you can retreat whenever you want to ignore the world and just spend some time alone all by yourself.
A layout square, or combination square, comes in 6” and 12” sizes. Most woodworkers use the 6” model, simply because it’s easiest to carry around. Also, most of the stock you’ll use will be no bigger than 6” wide, so 12” is overkill. The layout square is a triangle that you can use to mark square cuts on stock. Once you measure the length of the cut, you line up the layout square with the edge of the board. The short side will give you a straight, square cut across the end grain. You can also measure off angles with the layout square. This helps when you’re trying to measure for a bevel on a table saw, or marking a cut for a miter saw. You can even use your layout square to determine an existing angle. Just be sure to buy one made of metal. The plastic ones are not only fragile, but they also can warp, making them pretty useless.
Your moisture meter should have settings on it that will account for different species of wood. For instance, oak is a hardwood, but ebony is an even harder density wood. If you are planning an inlay job using both types of wood, you will need to know the moisture content levels of each of the two species so that your inlay glue joints will stay intact. These different wood species have different specific gravities, which must be used or programmed into the moisture meter.
Probably the handiest shop accessory in this list would be the woodworker's bench, complete with a vise. The bench is a stable-based table with a thick, hardwood top. In the top are a series of holes that are designed to accommodate bench dogs, which are little more than pegs that can be moved from hole to hole as necessary. The end of the bench has the aforementioned vise that works in concert with the bench dogs to hold pieces steady for the woodworker.
Adirondack Chairs in Tennessee Cedar Wood Growing up in Central New York and spending years in the Adirondack Mountains, I grew up seeing all types of Adirondack chairs. But it was not until I moved to middle Tennessee that I attempted to build Adirondack chairs myself. I found plans that gave me the basic design to build the adult chairs. I made some adjustments in order to fit them into my style and the type of wood that I have available. I found a cedar mill within an hour of my shop that allows me to purchase rough cut lumber. Because of the nature of rough lumber I am buying wood that is actually thicker, wider and longer than wood purchased at a brick front store.  Where a nominal 2”x 4”x 96” bought at a local lumber store is actually 1.5 x 3.5 x 96. The cedar I purchase is 2 ¼ x 4 ¼ x 102 inches. Once run through the surface planer to clean up the roughness and sanded, I am able to build with actual 2” x 4” or 2” x 6” lumber. This makes the chairs heavier, sturdier and more durable. Because of the size of the wood I assemble the legs and main supports with 3/8” carriage bolts. The arms, seat boards and backs are all assembled with 2” to 3” exterior screws. I predrill all the holes prior to inserting any screws. I do this because cedar, or any wood for that matter, can split at any time. The actual finished chair stands 38” tall x 39” long and 33” wide. They weigh about 35 lbs. and can seat a large adult very well but also comfortable for my tiny framed wife. The rise of the seat from the knees to the ground for your feet is 13 ½ inches. The seat reclines backward naturally but not so much that it is hard to stand from a seated position. The back is curved to support the natural curve of your back allowing for a more comfortable fit. The back is 32” tall to support even a taller person. The arms have been described as looking like whales so they are narrow where they fasten to the back of the chair and wide in the front for a cup, a book or even a laptop if you choose to work outside. *DISCLOSURE: Some of the links below are affiliate links. If you chose to click through and make a purchase I will earn a commission but there is no additional cost to you. It helps compensates the business for the time spent creating these posts. THANK YOU! Child’s Chair: The smaller child chairs are added to match the adult chairs to finish the family. These also are made with rough cedar milled and sanded to size to make the chairs sturdy. As with the adult chairs the wood will be thicker, wider and stronger than nominal wood. I use all true 1” lumber for the
×