Oh do I need this!! I have been trying to remove the damaged veneer from a great antique table, but after many hours I think I will have to give up and try a new top. I want to make sure I understand……If I have a good base on the table, I just cut the board lengths I need and glue to the origianl table top? Do I need to secure the new top with screws from the bottom? I think the boards will give this table a whole new life. I can’t wait to finish it. Thank you so much for being here TODAY!
A review of the Dewalt dwp615 The Problem Using a router inside the shop makes for a dusty shop. In the past when using my hand held trim or plunge router I would roll the projects out of the shop to avoid the mess. While this is fine in good weather, when it gets cold or rains it’s not an option so I use the tool inside and clean up the mess afterwards. The Solution I located a dust collection for my Dewalt dwp611 trim router and the dnp612 plunge base unit on Amazon and purchased the dnp615 and the dnp616. See my YouTube channel for the actual test and review. I tested them both with cedar because it is a wood that makes the most dust in my shop. Installation was easier than expected and fit into both bases. Using the trim base I was able to use the round over bit without any issues to achieve a clean cut and eliminate 85-90% of the dust. I did find the unit attached to the plunge base would not allow round over bits to extend deep enough to make a good cut, but with a straight bit it works great. Both Amazon links are available are below I would say this is a successful purchase and has eliminated the majority of the dust put out by the router. *DISCLOSURE: Some of the links below are affiliate links. If you chose to click through and make a purchase I will earn a commission but there is no additional cost to you. It helps compensates the business for the time spent creating these posts. THANK YOU!    

The table tops are double-sided – two for one! – and are 2 feet square. The cost of the project will vary based on items you might already have but the biggest expense is the wood at about $25 – that’s $12.50 per “table” – not too shabby at all, especially when you think about the alternative of actually buying an entire table. Or the gigantic house you’d need to store all that extra furniture!
I purchased these gloves for work, which involves handling and packing several (thousand) books everyday. When they arrived, they were a little too big for my smallish hands. I figured I would use them anyway to spare my sore fingers, and for the week I used these my hands were safe and papercut-free! The grip dots were secure and helped to grip even thin sheets of paper. The fingers bunched up a bit, but that's to be expected from oversized gloves.
A magnetized screwdriver or driver bit makes starting screws a lot easier. It’s like having an extra hand to hold the screw. We also like to magnetize a screwdriver when working with tiny screws that are nearly impossible to find if you drop them (been there?). You can use a magnetic bit holder in most cases, but not in tight quarters. Instead, you can just magnetize the bit. We’ve even magnetized tweezers to help pick up tiny parts.
Diablo's 3 piece Adjustable Cabinet Router Bit Set Diablo's 3 piece Adjustable Cabinet Router Bit Set features a rail and stile bit set and a Double Shear raised panel bit. Featuring TiCo carbide with titanium these bits provide a long cutting life and ultra-fine finish. Perma-Shield Diablo's high performance coating reduces friction and build-up on the bits. The ...  More + Product Details Close
**Important!  Be sure to pre-drill the holes for your screws before attaching the base to the table top!!  If you read the blog, then you know my table top ended up splitting, starting at a knot on the edge.  I’m pretty sure the cause of this was the fact that I attached the base to the top with screws without pre-drilling the holes, and I screwed right into a weak spot at the knot.  Learn from my very frustrating mistake, and don’t try to take short cuts!!
Probably the next most useful shop accessory is a large work table. I like to use a portable table that can be moved around the shop as needed. This particular table, which you can build by clicking on the link above, is lightweight yet sturdy and has retractable casters. When you want to move the table, simply lift each end and the casters lock into place to allow the table to roll. Once you get it into position, pull the cord on each end and the casters retract, so the table won't move.
We will suggest you select the simple Birdhouse if you are new at woodworking but be sure to select its design with respect to the place where you are going to hang/place it. One of our simple Birdhouse tutorials will help you building one. We have managed to include a source tutorial below that will help you to understand illustrates and the instruction to building a simple Birdhouse.
This plan is probably the easiest plan ever added in the list. The one who is working on this project, don’t need any professional skills but just knowing some basics of woodworking will be enough for this DIY. You will get step by step detailed process of this tutorial in the source linked tutorial. This tutorial will surely help you to build this plan quickly.
There are lots of clear finishes. But for a combination of usability and durability, you can’t beat polyurethane. Oil-based poly, which dries slower than water-based, is best for beginners because it allows more working time. The other important difference is clarity: Water-based poly is absolutely colorless, while oil-based has an amber tone, which can be good or bad depending on the look you want.
Using pocket holes to attach the stool base to the stool top prevents the top from moving during seasonal changes. It’s also not a good idea to drive screws through the edge of the apron into the table top. Over time the top could crack or the top could have enough force to push or pull the joints of the base apart. Skate over to Mistakes with Wood Can Cause Your DIY Furniture to Crack to see more about how I incorrectly attached the top on the stool.
Keep your woodworking tools and knives razor-sharp with our wide variety of sharpening supplies and accessories. We have what you need for jointer and planer knife sharpening. For sharpening plane irons and chisels, we supply a variety of diamond and waterstones, the Infinity Sandpaper Sharpening System, and honing guides. Our power sharpening systems include the Worksharp Knife Sharpeners, Ken Onion edition for the sharpest knives in the drawer.
Building a table is one of the most deceptively simple woodworking projects going. What could be easier than gluing up a few boards and applying a finish, right? But reality is often surprising, because building a top for that table can go wrong in ways you might not realize until it’s too late.  Here are my favourite tabletop construction tips, plus advice on how to avoid trouble. 

Work at a place where you’re required to wear a steel-toe boot? Then listen up. Wolverine just introduced a new boot that’s much more comfortable but still offers solid impact protection. Instead of steel, CarbonMAX boots have a protective cap made of carbon nanotubes, making them lighter and thinner. And if anyone knows about making comfortable work boots, it’s Wolverine—they’ve been making them for more than 130 years.
Woodworker's Supply is the expert's source for woodworking tools and hardware. We have the latest table saws, band saws, scroll saws, mortisers, jointers and planers for you to choose from. Looking for name brand cordless power tools or electric routers, router bits, and router accessories? We have a huge selection available. We represent the most respected brands on the market like Powermatic, DeWalt, Freud, Woodtek and many more. From traditional hand tools to high-tech digital measuring devices, we have what you need for the most intricate woodworking projects at woodworker.com.
This time I surprised one of my favorite dice games and took it outside. I made a set of wooden dice in just a few hours, and instead of sitting in the room and doing nothing, we are taking our dice game out into the yard. With this set of wooden dice, dice games are becoming our favorite backyard game. Check out the step by step tutorial below so you can make your own.
Even a small tabletop presents a challenge if the boards you glued together  have stepped-shaped misalignments where they meet because of warping. Yes, you can sand these off, but the more topographical sanding you need to do, the less flat and regular your finished tabletop will be. The flatter and better aligned your boards are when they’re in the clamps, the happier you’ll be later. This is where end clamps and gluing cauls can help.
A trusty pair of Electrician Scissors is the most used tool of many of the low-voltage electricians that we’ve talked to, and Klein seems to be the go-to brand. If you’ve never heard of electrician scissors, here is a primer: Of course like any scissors, Klein’s new Electrician Scissors can cut through stuff with the blades, but they also have a cable cutting notch so you can rip through wire up to 14 AWG. They’ll strip 19 and 23 AWG wire all day long and have a notch in the tip for de-burring electrical boxes. There’s also a scraper on both blades for convenient wire cleaning. Klein’s All-Purpose Electrician’s Scissors are available online and in home centers for $24.35.

Hanging upper cabinets is a tough task for one person. Having a lifting buddy to help is usually a good idea but costs extra. Little Hands HD is perfect for the guy who mostly works alone. The 6 x 6-in. base keeps the cabinets stable, and each lift can handle 150 lbs. The lever action can be raised a tiny fraction of an inch at a time, but sneak up on your target height because lowering the lifts isn’t quite as easy.
A super simple iPad Dock/stand made out of a single block of wood features an angled groove which gets to support the tablet device and a cut in a hole to revise access to the home button of your iPad. It’s possible to drill an access channel in the stand through which you can run a charging cable, although this mini stripped back iPad stand may have very limited functions.
For starters, this DIY wood table is for my son to keep his Lego projects and erector set buildings on. Secretly, it’s for me because, in turn, it will keep the Legos from being scattered all over my house. We decided on measurements of 60″ long x 18″ deep for the table top. Now that I know how big I want our homemade table to be I reached out to Osborne Wood Products to find out what the next step is for building a table. They were super helpful and made it very easy to order the table base kit. We let them know the measurements for the table top as well as how much of an overhang. We then choose the traditional dining table legs in soft maple along with a 4″ wood skirt also in soft maple. The furniture kit came well packaged and rather quickly. 
Because we were putting our new table cover over our existing table, we needed a rim that would hold it in place that was made of 1x2's. The 1x2's are an inch and half wide so adding two of those adds three inches overall to the length and width. I also added an extra 1/8" overall to both the length and the width so that there was a gap underneath so that the table could easily come on and off.
As with most websites, we do log web visits. This information, however, does not have a link to you personally. These logs help us understand the needs of our audience and the areas of our site that you do or do not find useful. When you simply browse our site, no personal information is being collected.  We may disclose this non-personal information to third parties such as sponsors, clients or advertisers.
The engineering involved in building this garden bench is pretty simple, and we have provided some links to get a full cut list and plans with photos to help you along the way. Additionally, to the stock lumber, you will need wood screws, barrel locks, and hinges to complete the table. A miter saw or hand saw is also extremely helpful for cutting down your stock to the correct angle and length.
Hey Cara – We bought MinWax wooden stain in Cherry (the teeny, tiny can) and one other color, but it has been misplaced in the garage somewhere. We picked up sample sized containers of paint in Satin finish (we bought them at Lowe’s so it was Olympic brand). I just found pretty blue and dark red paint chips and the paint counter guy did the rest! Hope that helps – happy to answer questions if you need any more info
From the source tutorial, you can get illustrates to the instruction about the plan. Everything is fairly described as diagrams, images, the list of supplies and tools need etc. The process to this plan is very easy to understand and follow for if you are having some basic woodworking knowledge. Make sure to collect all the supplies you need before you start with the project. You may even ask any question directly in the comment section of the tutorial post and also comment the images of your final product if you have completed it. Either way, I hope that you will manage to build this one nicely.​
Working on one side at a time, glue and nail the side to the back. Apply glue and drive three 1-5/8-in. nails into each shelf, attach the other side and nail those shelves into place to secure them. Clamps are helpful to hold the unit together while you’re driving nails. Center the top piece, leaving a 2-in. overhang on both sides, and glue and nail it into place. Paint or stain the unit and then drill pilot holes into the top face of each side of the unit and screw in the hooks to hold your ironing board. Mount the shelf on drywall using screw-in wall anchors.

If you want your table top -- any table top -- to actually ast without bowing/cupping/twisting, you MUST attach it in a manner that allows for seasonal wood movement. Wood is an organic product, and it naturally expands and contracts with changes in temperature and humidity. I'll post link below to a couple of options that you can cheaply buy which will allow you to securely attach a tabletop while still giving the wood the flexibility to move with the seasons. When you buy decently-made furniture at a store, they all accommodate for this one way or another. Don't just screw the top down to the legs or the skirt...you'll regret it later on.
Hi Mitchell – Thank you for the heads up… I thought I mentioned that in that in the post, but you’re right, I didn’t. Yes, wood expands across its width, so in order to allow for expansion/contraction there should be a small gap where the edges of the boards meet the apron. You don’t need a gap where the ends of the board meet the apron because wood doesn’t really expand/contract in this direction.
PROCESSING NOTES: No matter how easy I have tried to make following these media center plans and constructing them, if you find it overwhelming to attempt the project or operate the basic tools necessary for completion, get help. Contact your local supplier to see if sheet goods can be ripped to fit your car trunk. The possibility of ordering all the parts ready for assembly is also available. Most importantly, when you set off to build your project, help is only an email message away.

Do you enjoy splinters or cuts from metal flashing? Nope me neither. THESE GLOVES ARE THE SHIZ NIT! I have yet to get a splinter when handling my rough-edged plywood. Not only are they cheap but extra reliable. Mom these gloves are for you (My poor mom always gets splinters when she helps me DIY). This is one of the unique tools you’ll be happy you own.
OK, the Long Ranger’s been around since Marconi. But we love it. Simply put, this Long Ranger III Remote Dust Collector Switch is a remote system for turning on your dust collector out in the shop from whatever tool you’re operating. It plugs into the wall, you plug your dust collector into that and you’re done. Push the button on your remote and it fires right up. It’s saved us about two years and 1,300 miles of walking back and forth to the dust collector switch.

Let’s start with perhaps the most basic tool in every household – the claw hammer. The claw on one side of the head should be well counterbalanced by the finished head, which should be somewhat rounded. The other kind of head is the waffle-head. Most commonly used in construction, it leaves a distinctive waffle mark on the wood when you drive the nail. This, of course, is not the proper nail for woodworking.
The next important hand tool for the woodworker is an accurate tape measure. Get a retractable one that is at least 25 feet long. Any longer than that, and you start having problems getting it to roll back up. Since measurements on large scale projects can be very susceptible to even the most minute measurement variations, you’ll want to make sure the “hook” or tab at the end of the is firmly attached, with no give. When they get loose, you’ll have as much as 1/8” variation in your measurements. This can add up to some severe accuracy problems in the long run.
Now it’s time for one of the trickiest parts–attaching the side rails to the legs. I did this part on top of the tabletop, because it was the flattest surface I could find. We got the rail perfectly straight and I had my wife stand on it to keep it steady as I drilled the pilot hole through the leg and into the rail. Then we screwed in the 6″ lag screws. And I just about broke my arm trying to use a power drill with a socket to do this.

There is no cost to use the database. Registering is not required. You should be able to browse the database and click through the links. Having said that, considering the fact there are so many browsers out there being used, this site's software might not allow some visitors to browse, it all depends on the Internet traffic, and your browser's compatibility.


Just redid my dining room table with this technique and I an observation/suggestion others might find helpful. The boards did not line up well putting it together upside down, even on a flat concrete floor with me standing on the boards while they were screwed. I would have combined biscuits with the pocket holes to ensure a better alignment of the boards. Lots of sanding was required after assembly, and this might not be a huge deal with pine, but I used hard maple so it was quite a chore even with a belt sander. Also, be aware that the 1x2s around the edge may not line up perfectly -- I had to trim about an eighth inch from each side after assembly to get nice smooth, even edges. Not a big deal, but the top turned out a little smaller than the specifications I was give by SheWhoMustBeObeyed. Otherwise our table now looks great, and thank you for the post!
Probably the handiest shop accessory in this list would be the woodworker's bench, complete with a vise. The bench is a stable-based table with a thick, hardwood top. In the top are a series of holes that are designed to accommodate bench dogs, which are little more than pegs that can be moved from hole to hole as necessary. The end of the bench has the aforementioned vise that works in concert with the bench dogs to hold pieces steady for the woodworker.
Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth. It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed.
Nightstand table plans have everything you need to create a bedside table to keep every needy thing at reach at night time. This Nigh Stand plan is quite different in design from the most of the other plans. This stand has not only the three regular drawers but also having a hidden drawer that uses a secret locking mechanism to keep contents securely.
×