If you already have a workshop and the skills for woodworking, you will need to make sure that you have some reliable woodworking plans at your disposal and the necessary woodworking tools to complete the projects you wish to make. There are some websites that offer free woodworking plans, but they are often incomplete or lack sufficient detail to understand properly and this will lead to frustration and loss of interest in woodworking. After spending many years building up your collection of fine woodworking tools and learning to use them, you will no doubt have some neat skills under your belt. Now to make full use of these skills, you will need to find a nice project to work on, one which will do you proud and show off your fancy woodworking skills.
Hey Cara – We bought MinWax wooden stain in Cherry (the teeny, tiny can) and one other color, but it has been misplaced in the garage somewhere. We picked up sample sized containers of paint in Satin finish (we bought them at Lowe’s so it was Olympic brand). I just found pretty blue and dark red paint chips and the paint counter guy did the rest! Hope that helps – happy to answer questions if you need any more info

Or if you are in the search for a protectant that is specifically for woodworking tools, then you should check out the Restore Blade and Bit Cleaner 500. Not only is this cleaner one of the best woodworking accessories, it’s also environmentally friendly and safe to breathe in while using. This cleaner is the perfect companion for circular saws, miter saws, router bits, drill bits, as well as a variety of woodworking tools. While protecting your tools from rust and corrosion, it’s liquid form will not damage any wood materials that you may be working on at the time.
Creating a classic toy: One of my favorite shop projects is to create children’s cedar building blocks from rough Tennessee red cedar. These came about after I built my first Adirondack chairs and I had a large amount of scrap wood left over. Our first granddaughter had just been born and we decided to build a set of building blocks. Since that first set of blocks was made I’ve delivered hundreds to young children all across the country. Hearing the stories of the kids playing with these for hours and seeing the joy on their faces is what it’s all about. *DISCLOSURE: Some of the links below are affiliate links. If you chose to click through and make a purchase I will earn a commission but there is no additional cost to you. It helps compensates the business for the time spent creating these posts. THANK YOU! Start with Rough Cut Cedar These blocks start with rough 2×4 and 2×6 cedar lumber purchased from my local cedar mill. I use my Ridgid Power Tools Surface Planer to bring the wood into smooth milled lumber. Over to the SuperMax Drum Sander to sand the wood as much as possible. The goal is make sure the wood is as soon as glass. Then the wood goes into my Ridgid table saw to be milled into ¾ x ¾, 2 x 2 and ¾ x 2. Once the pieces are cut to proper width its over to the Grizzly Band saw to cut the blocks to length. I tried to do this on my sliding miter saw, but found I could not control the blocks well enough and the saw blade would cause them to either get jammed or fly across the shop and be ruined. Block Sizes These blocks come in a number of rectangle and square sizes. ¾ x ¾ x 2”, 4” and 6” ¾ x 2 x2’, 4” and 6” 1 ½ x1 ½ x1 ½ 2 x2 x 2”, 6” Final Step by Hand The last step is to take them to the Ridgid Oscillating Sander and round over the edges and corners to keep them safe. Because we handle them multiple times it gives is the opportunity to clear out any misfits and chipped blocks. Watch the process here. At one point we were coating them with a finish used for salad bowls but they were hard to dry without leaving ridges from the drying racks or drips that needed to be sanded off. It was recommended/suggested by a number of mothers that we not put anything on them. The beauty of these blocks is they hold the smell and are safe to play with. They provide hours of fun when stacking and building. I have watched the little ones learning how to pick things up grab and hold them. Available to purchase on Etsy Interested in having your own set? We have a limited amount available for Christmas 2018 with or without the hand made wooden 

I’ve been doing a lot of remodeling on my house and this wristband has come in pretty handy. The magnets work very well and able to hold all the screws, washers, and bolts for the different projects I’m working on. The pockets are a great addition too for holding plastic items. In fact, I found it useful for holding a small pencil where I can have quick access to for marking measurements for cuts. Overall it’s a great quality wristband and would definitely recommend.
When you buy the wood, look for pieces that aren’t warped, excessively longer or shorter than the others, and, if you can get lucky, don’t carry the telltale “new wood” planer marks. We purchased the most inexpensive wood that we could find. You’ll likely find them in 2- and 4-ft pieces. If you have a saw at home, you might consider getting the 4 ft pieces to decrease the cost of your project a bit.
By video tutorial, you will get step by step process instructions of making a nice wooden folding sling chair from scratch. However, my first wooden chair was not the best one, but it was good enough to motivate me to make some more folding chairs like this one. If I can make this, you too can make one yourself. You can browse the internet for more folding sling chairs ideas and start making one now.
Here’s a traditional Swedish farm accessory for gunk-laden soles. The dimensions are not critical, but be sure the edges of the slats are fairly sharp?they’re what makes the boot scraper work. Cut slats to length, then cut triangular openings on the side of a pair of 2x2s. A radial arm saw works well for this, but a table saw or band saw will also make the cut. Trim the 2x2s to length, predrill, and use galvanized screws to attach the slats from underneath. If you prefer a boot cleaner that has brushes, check out this clever project.

The Story of the Farmhouse Table with a Race Track While working my day job one of my managers came to my desk and said “I need your help”. Come to find out she ordered a farmhouse table and bench on Etsy. However the person she ordered it from fell off the face of the earth and left her without a table or her money (Etsy made good on it for her). The reason she ordered the table was because of the three legged bench. She has a young son and was concerned that he would turn over a two legged bench. This one appeared to give her the stability that she wanted. My reply, “I can help!” After seeing the picture of the table she ordered I told her to give me a few days and I could find her an alternative. So I went out to one of my trusted bloggers, Rogue Engineer and found the table I wanted to build. Please check out his site and follow him on social media. After getting her approval of the style and layout, we agreed on a price and some minor adjustments to the plans. She only wanted a 7 foot table and she only wanted one bench, but that bench needed a third leg. So I made the size adjustments and quoted the table. Now the “Curve” A couple of days after we agreed on the project my client called and said she had an idea on the way to work. She needed to find a way to get her son to the dinner table. “Can I add a 1½” wide by 1/8th inch deep race track around the top of the table?” After I caught my breath and recovered I gave her some alternative ideas to avoid creating a race track into what I knew was going to be a beautiful table. She was convinced this is what she wanted, so I said well, this is why we call ourselves Bayne CUSTOM Woodworking. So I agreed and then the adventure began. The Build Instead of recreating what Rogue Engineer already did I will refer you to his free plans on his site. See the link in the opening paragraph.  He will provide the materials list needed. Below I will outline the changes I made and how I built the table and bench. While not huge changes, there are some that I made to meet the client’s requests and some to add my own unique style. The plans call for a table that is 110” while I made mine to fit the client request of 84”. Because I trimmed my boards I ended up with a 40” wide top instead of a 42” wide. She wanted only one bench so I made an 80” bench with 3 legs instead of the 2 legged bench. Let me also state up front that I rarely, if ever, use pine to build anymore, but I did use it on the job because
This is a very colorful and fun project. The idea is to use an old table with a top that you don’t really like and to give it a makeover. You don’t need paint for this project, just a lot of colored tape. Use it to make stripes to cover the entire surface of the tabletop. You can also wrap the edges in tape. You can also cover it with lacquer or add plexiglass on top to protect the design.
Check out our most recent woodworking tools and accessory reviews below. We have thousands of satisfied customers that use our router bits, shaper cutters, router tables, and many more fine woodworking tools every day. Take a minute to read what your fellow woodworkers have to say about their experience with our company and our quality woodworking tools. All reviews are from real customers of Infinity Tools who were polled by our partners at ShopperApproved.com. More third party reviews can be found at Shopper Approved's website.
To save money, we keep the temp in our shop down low when we’re not in it and crank up the heat when we return. But even when the air temperature hits 70 degrees F, the concrete floor is still Minnesota-cold. We tried a space heater under the bench, but it broiled the shins and still left us with cold feet. So we recently bought a foot-warming mat, and now our feet stay toasty warm. Plus, it uses a fraction of the electricity and is a lot safer than a space heater. The mat is produced by Cozy Products. The good folks over at Cozy suggest putting a chunk of cardboard underneath it if you use it on flooring that could fade from the heat, like carpet or wood.
Clamp curved caul edges inwards so they align tabletop boards in the middle, then torque up the main clamps to draw the boards together. If the width of boards you’re using allow it, pre-glue boards for your tabletop in sections that are just narrow enough to fit within your thickness planer. Run these through the planer to clean and level the glue joints, then move back to clamps for final glue up. Working in stages like this reduces the number of glue joints you need to sand smooth and level later.
Taking cabinet building to the next level I wanted to take another step in my building and see if I could build a cabinet without the use of screws. My wife found the plans in an old Woodsmith Magazine and asked me to build the largest bookcase of the set. My plan was to build the entire cabinet using dowels instead of screws, dado slots instead of pocket hole joinery and biscuit joints. Using rough oak purchased from a local lumber mill, I milled and sized the lumber to the specifications to create this book cabinet with 5 shelves. It was time to replace a number of older pine book cases in the house. Instead of using the traditional pocket hole joinery, the sides, shelves, doors and face frame were all joined using 3/8” dowels,biscuit joints, dados and glue. I used tempered glass for the doors for safety which I was able to purchase locally. The glass vendor recommended using silicone caulk to secure each pane before applying a few small mirror catches on all the sides. The doors were each hung with 3 Ball-Tip Full Back-to-Back Wrap-Around Inset Hinges. Finished with Minwax English Chestnut and homemade wiping polyurethane, this cabinet will stand the test of time and hopefully become a keepsake that is passed down through generations. *DISCLOSURE: Some of the links in this post are affiliate links. If you chose to click through and make a purchase I will earn a commission but there is no additional cost to you. It helps compensates the business for the time spent creating these posts. THANK YOU!
Some tools required to build a picture frame are a table saw, miter saw, measuring tape, wood glue etc. A table saw with a backing board and miter gauge can be used to get the right angle and lengths of picture frame every time. You can use builders square to arrange the final cut pieces before nailing, screwing or gluing. Check out the video tutorial below for more details.
You might be able to reproduce the same concept that the table with leaves has. Instead of putting the clips on the underside of the table (since that would not allow it to lay flat over the existing table) perhaps you could get smaller hooks and place it on the underside where it overhangs on the side. Would be a little more work, but definitely cheaper than a new table. 😉
In an effort to replace the table, I started looking at garage sales and on craigslist for replacements. I was coming up empty handy {they all looked worse than ours!} or being totally priced out.  I started to think, why not just use the table that we have and slap a few boards on it.  My engineer husbands thinking is a little more refined than "slapping" boards on something, so he came up with an idea {and like a true engineer made an auto cad design}, we tweaked it a bit together and then took a little date to Home Depot. Because that my friends, is where adults go on dates.
One of the best stud finders you’ll ever use is the Franklin Sensors ProSensor 710. It’s unique in that there’s a whole bar of red lights that light up whenever it detects a stud. Unlike other sensors, which have a single light that stays on as it passes over the wood, the lights on the 710 tell you exactly where the wood stops and starts. No guesswork. Push a button, drag it over the wall and those hidden mysteries reveal themselves. You won’t even need to read the directions! 

Some moisture meters have pins that penetrate the surface of the wood. This can leave tiny holes that mar the surface and require filling. Others are pin-less. They have sensing plates that scan the wood beneath. However, not all pinless moisture meters are the same – look for one that uses technology that is not affected by the surface moisture in the wood, such as Wagner Meters IntelliSense™ Technology Moisture Meters.
You can also use Google image search to research a project. Unlike the PDF search, the image search provides a photo of what the project will look like, which is helpful in determining if you want to pursue building it. By doing an image search for how to build a step stool, you will have a ton of options that all lead to woodworking plans of various quality. (The how to part of these is important—otherwise you’ll just get pictures of step stools.)

An assortment of chisels should be part of every workbench. Chisels are not just for wood carvers. Any woodworker will need chisels to clean out joints and saw cuts. Look for chisels made of high-alloy carbon steel or chromium-vanadium alloyed steel. Hardwood grips are best, especially if they have metal caps on them. This will keep the end of the handle from becoming malformed when you hammer on it.

Bought 2 of these, one for the wife and one for me. We have a project we are doing that required cutting lots of MDF(medium density fiberboard) which is not good for you to breathe or get in your eyes (very tiny particles). I picked these because people said they worked well with glasses (which i wear) and because they had full protection from flying debris and also from the airborne dust.
Leave your tabletop longer than necessary until the sanding is done, then cut to final length. Most tabletops are too wide to trim on a tablesaw, even with a crosscut sled, and this is where I use a hand-held circular saw. Clamp a guide strip so it’s square to one edge, then follow it with your saw. Repeat the process on the other end, then carefully use your hand-held belt sander to remove any blade marks on edges. It sounds like a coarse process, but you can get great results this way.
Clamp curved caul edges inwards so they align tabletop boards in the middle, then torque up the main clamps to draw the boards together. If the width of boards you’re using allow it, pre-glue boards for your tabletop in sections that are just narrow enough to fit within your thickness planer. Run these through the planer to clean and level the glue joints, then move back to clamps for final glue up. Working in stages like this reduces the number of glue joints you need to sand smooth and level later.
A heavy-duty hardened steel chain with hexagonal links will thwart nearly every thief with a bolt cutter. Hexagonal links (or square or trapezoidal) make it impossible for bolt cutters to get a grip. You may be tempted to buy chain by the foot at the hardware store, but it’s designed for lifting and towing, not theft resistance. Even the thick stuff is likely to have round links, and frankly, if a hardware store clerk can cut the chain easily, a thief can too.
It’s important to have an understanding of wood when building DIY furniture projects. Not just how to cut, and assemble with wood but also to understand how it works. In Mistakes with Wood Can Cause Your DIY Furniture to Crack we talked about how wood is hygroscopic. Simply put, hygroscopic means it absorbs moisture from the air. Seasonal changes cause wood to absorb and release moisture.

The result of this project is what your wife or girlfriend would call a “Rustic,” “Barn,” or “Ranch Style” dining room table. I call it a man table, because it’s made from inexpensive wood, can take a beating, and one day your grandchildren will be serving their kids Thanksgiving dinner on it. Being the man that built that table is, well, manly. I’ve found a few similar tables on Craigslist and furniture sites, starting at around $1200. That’s absurd. I built mine for less than $200, including the chairs I bought for it.
A dispensing gun allows you to save foam if the job requires less than a full can. Once the job is finished, just set the gun aside until the next time you need it. Leave the can on the gun if you know it will be used in less than 30 days, or pull the can off, cap it and then clean out the gun with cleaning solution. Besides saving you money on foam, the dispensing gun provides much greater control because you’re not working with a flimsy straw, and the trigger can be adjusted with a turning setscrew to control the rate of flow—nice! Spray foam dispensing guns are available online and at home centers.
There is no cost to use the database. Registering is not required. You should be able to browse the database and click through the links. Having said that, considering the fact there are so many browsers out there being used, this site's software might not allow some visitors to browse, it all depends on the Internet traffic, and your browser's compatibility.
A dispensing gun allows you to save foam if the job requires less than a full can. Once the job is finished, just set the gun aside until the next time you need it. Leave the can on the gun if you know it will be used in less than 30 days, or pull the can off, cap it and then clean out the gun with cleaning solution. Besides saving you money on foam, the dispensing gun provides much greater control because you’re not working with a flimsy straw, and the trigger can be adjusted with a turning setscrew to control the rate of flow—nice! Spray foam dispensing guns are available online and at home centers.
×