This tool is specialized for the task of making shingles. The strange name comes from the antiquated word "froward," which means "away," in reference to the direction that the tool cuts. To use it, place the froe, blade down, on the edge of a log length, then hit the top of the blade with a wooden club, forcing the froe into the log. Next, pull the handle toward you and pry off a thin slice of the log. Voilà... shingle! Since buying a box of square-edged shingles is significantly less effort than making each and every one by hand, this tool has long since passed its heyday. But it still can be used to build up the kindling pile.

Even a small tabletop presents a challenge if the boards you glued together  have stepped-shaped misalignments where they meet because of warping. Yes, you can sand these off, but the more topographical sanding you need to do, the less flat and regular your finished tabletop will be. The flatter and better aligned your boards are when they’re in the clamps, the happier you’ll be later. This is where end clamps and gluing cauls can help.
This set of tools have helped a lot in my startup of woodworking. I'm an amateur, and these bars really helped me out. These have come to be very useful in my recent project, where I'm trying to build a kitchen open faced cabinet, and I needed to cut some dado's and these have helped quite a bit. I also used them to help set up my table saw to the correct height of he blade, to accurately cut slots by measuring the height of the blade for the slot cuts in my drawers. I've tried using rulers, but one needs 4 hands to make all the correct measurements. These cut out the other 2 set of hands.
Attach all four legs and set the top on the base with equal overhang on all sides. Carefully trace the leg tops on the bottom side of the planks and then flip it over onto a work surface. Drill a 1/2” hole with each square mark near the line but not touching it. Using a jigsaw, carefully cut out each square. Because leg tops will nest snuggly in these squares, be sure cuts are slightly undersized. Flip the top back over and attempt to set it on the base. Using a flat wood file and chisel, remove small amounts of material as needed. Once the top nestles down on the gutter structure without excess force, run a small bead of wood glue on the top edges of the gutter, reposition the top and shoot 15-gauge finish nails through the inside edge of the gutter into the bottom of the tabletop. Fill in small gaps between the leg top and table planks with wood filler or small wood shims.
Another fairly inexpensive option for making a table top is using a stain grade 3/4″ plywood. cut the 4 x 8 sheet in half (2- pcs, 4 x 4). Spread wood glue one and place and clamp the other on top. Once the glue has dried, it can be cut with a jig saw to the round shape, or if you have access to a router, make a “circle cutter” by mounting the router on a thin piece of wood, (1/4 x 6 x 60″) and putting pivot hole at a distance of 1/2 the diameter of the desired table. (from the side of the router bit to the pivot hole. Put a small hole in the underside of the table top as close to the center as possible. (not all the way through) and use something like a nail as a pivot. Use a straight bit and cut a perfect circle. The stain grade plywood usually has a pretty good stain surface and the construction of the plywood makes it pretty stable. After cutting the edge may have some minor voids, which can be filled with wood putty and sanded nice and smooth. The results can be a nice stained or painted surface.
If you can beg or borrow a pocket hole jig you dont have to predrill holes. I haven’t done a table top other than a workbench(Plywood!) but I have done cabinets and beds. The Kreg jig makes joining easy. A lighter stain colour would cut down on the grain marks, or a heavier application like an espresso stain. I will throw you a pic when I finish my table and show you what I mean.
She has permanently glued and screwed the tabletop within that four-sided, mitered frame. Attaching the skirt to the long edges of the wide boards is no problem, but fastening them to the end grain of the wide boards, as shown in the photo above, is. The builder has constricted the wide boards' movement, and as they grow or shrink in width but are held in place by those end-caps, they will warp and split, making this a short-lived piece of furniture.

Simply brilliant. Why didn’t I think of this? So we have a nearly 100 year old house. There is always something that needs repair. Thanks to whoever invented this little guy! No more mouth full of nails or screws. No more climbing up and down the ladder to get the damn screwdriver I dropped. Probably won’t hold your 16 oz claw hammer but other than that it is perfect. I love this. Highly recommend. Thanks for reading


Reclaimed Wood from Corn Crib HOW TO DESIGN AND BUILD AN ENTRY WAY COAT RACK AND BENCH There was a door in granddad’s home the client wanted to preserve and wondered, if they provided the wood, could I build an entryway coat rack and bench using the door as part of the build. The wood they wanted to provide, well, that was from the family owned Tennessee corn crib that had been torn down and they didn’t want to lose the wood or the memories. Not only was this a corncrib but it was eventually used by the great grandchildren as a play house. So for the client there are as many memories in this build as there are colors. THIS PROJECT TRULY DEFINES THE “CUSTOM” in BAYNE CUSTOM WOODWORKING. I spent some time to design a simple layout in @sketchup_official so the client could approve the idea I had in mind. The wood showed up in two deliveries so we stacked it outside because this was the first time I worked with barn wood. I did not want to introduce possible termites to my shop. So my first call was to my pest guy asking how I would treat the wood for termites. Much to my relief he said I had nothing to worry about. This was “real” wood! Not nominal at all, nominal is how we buy our wood at a local hardware store. Where a 2×4 is actually 1 ½  x 3 ½ . These 2×4’s were at least 2”x4”’s if not more and were hard, heavy and dusty, did I say heavy? After cutting to length on my handy @DewaltTough miter saw, I had to take them to my @ridgidpowertools table saw and square up the bottoms only.  I was very careful not to lose any of the original saw marks and character because that would ruin the entire purpose. For someone who likes clean, crisp edges, this was a bit of a challenge. I used @kregjig Kreg Jig® K4 Master System to join all the pieces of the base, the seat frame and the supports to join the two together. I was very careful to hide all of the pocket holes so they could not be seen from any angle. I used Titebond Products original interior wood glue to join all the pieces together. The next item was to assemble the back which included grandad’s door as the center piece. The door was only 71 ½ tall which determined the overall height of the project. Part of this back also includes two live edge pieces that we picked to use as the “L” shaped wings or side walls. The door measured 24” which left me with 6” on each side to make up the final size of 36”. So I chose two of the straightest boards that were closest to 6” and cut them to width so as not to waste any wood or lose any character. I used the Kreg Jig® K4 Master System
The Milwaukee REDSTICK can be used to screed, smooth, and level. Once you’re done, the level is preposterously easy to wipe clean. The REDSTICK also has all the great features you would expect from a Milwaukee level. SHARPSITE Vial Technology makes the magnified bubble easy to read and the REDSTICK’s magnesium core keeps the level from breaking down. The Milwaukee REDSTICK Concrete Levels are available in 24-in., 48-in. and 72-in. lengths starting at $99.99.
After all slots are cut, stand each board on end and coat the edge of jointed side with wood glue. Next coat the biscuits with glue. Insert biscuits in one side only of each board, then insert glued biscuits in the empty joint of the next board. Assemble planks in order until the top is complete. Don't worry about small gaps. Next, carefully lay the top down and attach pipe clamps at roughly 1' intervals. Slowly tighten each pipe clamp in a consistent fashion until the gaps disappear*. Small amounts of glue can be removed when dry; scrape up any puddled glue with a plastic putty knife. To minimize sanding later, avoid working glue into the top of the wood. Let the top set overnight.
By video tutorial, you will get step by step process instructions of making a nice wooden folding sling chair from scratch. However, my first wooden chair was not the best one, but it was good enough to motivate me to make some more folding chairs like this one. If I can make this, you too can make one yourself. You can browse the internet for more folding sling chairs ideas and start making one now.
Cut the 6-1/2-in. x 3-in. lid from the leftover board, and slice the remaining piece into 1/4-in.-thick pieces for the sides and end of the box. Glue them around the plywood floor. Cut a rabbet on three sides of the lid so it fits snugly on the box and drill a 5/8-in. hole for a finger pull. Then just add a finish and you’ve got a beautiful, useful gift. If you don’t have time to make a gift this year, consider offering to do something for the person. You could offer to sharpen their knives! Here’s how.
Cedar Mini Decorative Planters/Boxes Using Interlocking Dovetail Joints Having a cedar mill within an hour of my shop allows me to work with some very nice wood. While cedar can be brittle, it is wonderful to work with and makes putting these decorative boxes together a breeze. When working with cedar I am always looking for pieces that have what is known as “heartwood”. This is the red portion of the wood. When first planed or sanded, this heartwood is almost pink in color but takes polyurethane or spar finish well giving a vibrant dark red when applied. If left untreated, cedar will turn gray in direct sunlight and a dull red color from normal household light. These boxes have been treated with a wiping polyurethane mix that allows me to apply it with a cotton rag instead of a brush. It’s faster to apply, doesn’t run and dries fast enough to apply two coats in a day. So applying 5-6 coats only takes 2-3 days to accomplish. I assembled the boxes using a dovetail joint which provides both strength and decorative at the same time. A fan shaped tenon that forms a tight interlocking joint when fitted into a corresponding mortise. The dovetails on these boxes are shown on the length of the box and not the end where the handles are located. I use a dovetail jig and a router to make these joints which is more efficient. Depending on how the client will use the box I may or may not drill two holes in the bottom of the box. If they are built to be used as outside planters then I drill 2, half inch holes in the bottom for water to drain. If they are to be used inside as a table center piece or fireplace mantle decorative box, then I do not drill the hole. In the end they are strong, durable and beautiful no matter how they are used.
Building a bookcase or bookshelf is a fairly simple woodworking plan that you can get done in just a day or two. This is also a low-cost project as well and since the project idea is free, you don't have to worry about busting through your budget. Just follow the simple steps in the tutorial and enjoy your own company building a simple bookcase on this weekend.
Manufacturers that produce woodworking tools and materials have got into the content creation game, too, and some will share woodworking plans online. Minwax and Ryobi, for example, provides their plans free of charge, and Rockler offers their woodworking plans for a fee. Seek them out along with the other blogs and you’ll have a handy list of resources you can turn to for any project.
As with most websites, we do log web visits. This information, however, does not have a link to you personally. These logs help us understand the needs of our audience and the areas of our site that you do or do not find useful. When you simply browse our site, no personal information is being collected.  We may disclose this non-personal information to third parties such as sponsors, clients or advertisers.
In an effort to replace the table, I started looking at garage sales and on craigslist for replacements. I was coming up empty handy {they all looked worse than ours!} or being totally priced out.  I started to think, why not just use the table that we have and slap a few boards on it.  My engineer husbands thinking is a little more refined than "slapping" boards on something, so he came up with an idea {and like a true engineer made an auto cad design}, we tweaked it a bit together and then took a little date to Home Depot. Because that my friends, is where adults go on dates.
Buying a pack of pre-organized furniture and project plans if you’re new to learning is beneficial for several reasons. Firstly, the packs of plans allow you to access a constant source of instructional content from wherever you are, whether you’re in your shop or want to browse for ideas. There are many plan sources out there and huge amounts of plans being produced and being posted online and in forums each day. By paying a small fee to take advantage of organized woodworking resources, it is easy to learn the best techniques faster and begin making projects you will use for a lifetime.
Carefully lay the top down and attach pipe clamps at roughly 1' intervals. Slowly tighten each pipe clamp in a consistent fashion until the gaps disappear. Small amounts of glue can be removed when dry; scrape up any puddled glue with a plastic putty knife. To minimize sanding later, avoid working glue into the top of the wood. Let the top set overnight.
×