Taking cabinet building to the next level I wanted to take another step in my building and see if I could build a cabinet without the use of screws. My wife found the plans in an old Woodsmith Magazine and asked me to build the largest bookcase of the set. My plan was to build the entire cabinet using dowels instead of screws, dado slots instead of pocket hole joinery and biscuit joints. Using rough oak purchased from a local lumber mill, I milled and sized the lumber to the specifications to create this book cabinet with 5 shelves. It was time to replace a number of older pine book cases in the house. Instead of using the traditional pocket hole joinery, the sides, shelves, doors and face frame were all joined using 3/8” dowels,biscuit joints, dados and glue. I used tempered glass for the doors for safety which I was able to purchase locally. The glass vendor recommended using silicone caulk to secure each pane before applying a few small mirror catches on all the sides. The doors were each hung with 3 Ball-Tip Full Back-to-Back Wrap-Around Inset Hinges. Finished with Minwax English Chestnut and homemade wiping polyurethane, this cabinet will stand the test of time and hopefully become a keepsake that is passed down through generations. *DISCLOSURE: Some of the links in this post are affiliate links. If you chose to click through and make a purchase I will earn a commission but there is no additional cost to you. It helps compensates the business for the time spent creating these posts. THANK YOU!
You can also use Google image search to research a project. Unlike the PDF search, the image search provides a photo of what the project will look like, which is helpful in determining if you want to pursue building it. By doing an image search for how to build a step stool, you will have a ton of options that all lead to woodworking plans of various quality. (The how to part of these is important—otherwise you’ll just get pictures of step stools.)
With a pencil and a protractor, divide the larger disc into 30-degree wedges to create 12 center lines for the bottle indents. Center and trace the smaller disc on top of the larger disc. Next, with a drill press, drill 3/8-in.-deep holes on the 12 center lines with the 1-7/8-in. Forstner bit, spacing them between the disc’s outer edge and the traced circle. Next, divide the smaller disc into 60-degree wedges and drill six more 3/8-in.-deep holes with the Forstner bit.
I used a dry brush, barely dipped it in paint, and then lightly brushed it over the wood. If you get too much coverage with the paint, sandpaper is your best friend! You can stain the wood if you want a darker look peeking out from underneath. Check out the stain in this DIY post, it’s a great way to get that aged look quickly: http://www.jasonandshawnda.com/foodiebride/archives/11310
Here’s another example of a stenciled tabletop. Remarkably, this table was destined for the dump when Pretty Handy Girl pulled it from a dumpster. With a stencil, primer and paint, some distressing, glazing and sealing, she gave this beauty a second life – one in which it looks like it came directly from old world Scandinavia. // Pretty Handy Girl
We have a small dining room area in our farmhouse that is separate from the living room and kitchen. The area is much smaller in space than our last house. I was little confused that our typical rectangular farmhouse table was not going to cut it. So, I walked in I came to know that we needed to build a round dining table. So, I searched for a plan design idea and build a very own round farmhouse dining table. I was an amazing DIY plan, I just love it!
This DIY has a bit of a backstory: In my basement workshop—as a byproduct of about a half dozen previous projects—I’d managed to accumulate a small mountain of scrap wood. Though the pieces varied in size, most were 2×4 boards. For weeks, I pondered the question of how to use them. There wasn’t enough material to build anything substantial, but at the same time, this was much more wood than I would feel comfortable chucking or committing to kindling. I suddenly seized on the idea of turning those leftover boards into a rustic tabletop, but then I let the project momentum slow to a creep, and in the blink of an eye another few weeks had gone zooming by. Things finally came to a head one day when I was scanning the local giveaway listings. There, I discovered that one of my neighbors was trying to get rid of an old metal garden table. Upon seeing the pictures, I knew immediately that this would be a great table to top with the scrap wood surface I’d been planning to make with all those 2x4s!
Personally identifying information is information that can be used to identify who you are such as: name, mailing address, email address. To enter certain areas of the site, you will be required to register and provide information about yourself. This information is for the purposes of Canadian Woodworking and helps us to tailor the site to best meet the needs of our audience.
If you have some basic carpentry and tool usage skills, take advantage of Ryan's custom woodworking plans and the opportunity to build a custom entertainment center yourself with entertainment center plans, media center plans and woodworking plans designed and published by Ryan. If you don't, now is a great time to start. Its not as difficult as your may think.
The reclaimed wood boards are glued together, side-by-side, to form the table top. Use a biscuit joiner to cut matching slots along the board edges (Image 1). Because this tool can be set to cut the all of grooves at the same precise depth, when you insert the biscuits in the slots and pull the boards together the result is a smooth, level surface (Image 2).
There is no cost to use the database. Registering is not required. You should be able to browse the database and click through the links. Having said that, considering the fact there are so many browsers out there being used, this site's software might not allow some visitors to browse, it all depends on the Internet traffic, and your browser's compatibility.
If you already have a workshop and the skills for woodworking, you will need to make sure that you have some reliable woodworking plans at your disposal and the necessary woodworking tools to complete the projects you wish to make. There are some websites that offer free woodworking plans, but they are often incomplete or lack sufficient detail to understand properly and this will lead to frustration and loss of interest in woodworking. After spending many years building up your collection of fine woodworking tools and learning to use them, you will no doubt have some neat skills under your belt. Now to make full use of these skills, you will need to find a nice project to work on, one which will do you proud and show off your fancy woodworking skills.
It’s important to have an understanding of wood when building DIY furniture projects. Not just how to cut, and assemble with wood but also to understand how it works. In Mistakes with Wood Can Cause Your DIY Furniture to Crack we talked about how wood is hygroscopic. Simply put, hygroscopic means it absorbs moisture from the air. Seasonal changes cause wood to absorb and release moisture.
Example Entertainment Center: $25 for plans + $750 for materials + $1200 for good quality tools = $1975. Less than a few grand! Of course you don't have to buy brand new tools; search the sale lists online (i.e. Craigslist, Freecycle.org, etc.) in your area. You are sure to find some good deals on power tools and even materials! (A good set of tools includes a table saw, miter saw, nail gun and compressor and four piece cordless tool set.)
Creating a classic toy: One of my favorite shop projects is to create children’s cedar building blocks from rough Tennessee red cedar. These came about after I built my first Adirondack chairs and I had a large amount of scrap wood left over. Our first granddaughter had just been born and we decided to build a set of building blocks. Since that first set of blocks was made I’ve delivered hundreds to young children all across the country. Hearing the stories of the kids playing with these for hours and seeing the joy on their faces is what it’s all about. *DISCLOSURE: Some of the links below are affiliate links. If you chose to click through and make a purchase I will earn a commission but there is no additional cost to you. It helps compensates the business for the time spent creating these posts. THANK YOU! Start with Rough Cut Cedar These blocks start with rough 2×4 and 2×6 cedar lumber purchased from my local cedar mill. I use my Ridgid Power Tools Surface Planer to bring the wood into smooth milled lumber. Over to the SuperMax Drum Sander to sand the wood as much as possible. The goal is make sure the wood is as soon as glass. Then the wood goes into my Ridgid table saw to be milled into ¾ x ¾, 2 x 2 and ¾ x 2. Once the pieces are cut to proper width its over to the Grizzly Band saw to cut the blocks to length. I tried to do this on my sliding miter saw, but found I could not control the blocks well enough and the saw blade would cause them to either get jammed or fly across the shop and be ruined. Block Sizes These blocks come in a number of rectangle and square sizes. ¾ x ¾ x 2”, 4” and 6” ¾ x 2 x2’, 4” and 6” 1 ½ x1 ½ x1 ½ 2 x2 x 2”, 6” Final Step by Hand The last step is to take them to the Ridgid Oscillating Sander and round over the edges and corners to keep them safe. Because we handle them multiple times it gives is the opportunity to clear out any misfits and chipped blocks. Watch the process here. At one point we were coating them with a finish used for salad bowls but they were hard to dry without leaving ridges from the drying racks or drips that needed to be sanded off. It was recommended/suggested by a number of mothers that we not put anything on them. The beauty of these blocks is they hold the smell and are safe to play with. They provide hours of fun when stacking and building. I have watched the little ones learning how to pick things up grab and hold them. Available to purchase on Etsy Interested in having your own set? We have a limited amount available for Christmas 2018 with or without the hand made wooden
Now, the project starts to get really interesting. While I knew that I would use pocket-hole joinery (my latest obsession) to assemble the tabletop, I couldn’t decide how to finish the wood. There were three different cans of Minwax Gel Stain on my shelf, in three different colors—Hickory, Cherrywood, and Honey Maple. In my head, I could make a credible argument in favor of each one. And though it would have helped to know where the table would eventually go, that was another question I couldn’t answer. Then it hit me: Rather than choose one stain, why not use them all? After all, I was constructing the tabletop from scraps, so it was going to have a homemade, mosaic look no matter what. In the end, using multiple stains would emphasize the rustic effect the table was going to achieve. Perfect! From there, having fought my way to a project plan, the rest came easy. Read on to see how I built the tabletop, then stained and sealed it with Minwax.
Hey Cara – We bought MinWax wooden stain in Cherry (the teeny, tiny can) and one other color, but it has been misplaced in the garage somewhere. We picked up sample sized containers of paint in Satin finish (we bought them at Lowe’s so it was Olympic brand). I just found pretty blue and dark red paint chips and the paint counter guy did the rest! Hope that helps – happy to answer questions if you need any more info
This is another wood table but this time with a more elaborate design. Instead of using a large log, this time you’ll need several small ones. The idea is to cut them to the same height and to try to create a mosaic with them. You can glue them together and you can also wrap a piece of rope or something similar around them. You should be able to create an original coffee table.