Once your table is completely dry, flip it over and push the edge of the table over your workspace edge. Go ahead and trim the excess maple so that it is flush with the MDF using a circular saw. Make sure these edges are straight and refined, as these will end up being the finished edges of your table top. Flip the table top over and sand smooth, wiping off any sawdust afterwards.
Do you have older 18V DeWalt tools that are still near and dear to your heart but need new batteries? Consider firing up those old tools with 21st century technology. Now, 18V tools can be run on powerful 20V lithium Ion batteries with DeWalt’s new battery adapter. The adapter slides into the tool and the battery hooks onto the adapter. It works on most 18V DeWalt tools but not all. It’s sold two ways: the adapter alone (DCA1820), or the adapter with two compact 20V, 2.OAh batteries and charger. Now you’ll be able to hold on to your favorite cordless reciprocating saw forever!
These unique clamps will save you time and aggravation in too many ways to list! MatchFit clamps slide anywhere along a groove routed with a common 1/2" - 14 degree dovetail bit and leave one surface of your work clear of obstructions. Use these clamps to create customizable clamping tables and for attaching table extensions, sub fences, stop blocks, hold downs, and more to your machinery and work tables. Imported.
While the top is drying, measure the thickest portion. Add 1/16” to this measurement and mark a horizontal line with a framing square across the tops of the table legs. This line marks the gutter structure mounting depth. Legs will protrude 1/16” above the plane of the tabletop. Ask a helper to hold the leg tight to the inside corner of the gutter structure with the mark at the top of the gutter. Drive at least two wood screws through the inside face of the gutter into the sides of the leg.
To save money, we keep the temp in our shop down low when we’re not in it and crank up the heat when we return. But even when the air temperature hits 70 degrees F, the concrete floor is still Minnesota-cold. We tried a space heater under the bench, but it broiled the shins and still left us with cold feet. So we recently bought a foot-warming mat, and now our feet stay toasty warm. Plus, it uses a fraction of the electricity and is a lot safer than a space heater. The mat is produced by Cozy Products. The good folks over at Cozy suggest putting a chunk of cardboard underneath it if you use it on flooring that could fade from the heat, like carpet or wood.
This is a very colorful and fun project. The idea is to use an old table with a top that you don’t really like and to give it a makeover. You don’t need paint for this project, just a lot of colored tape. Use it to make stripes to cover the entire surface of the tabletop. You can also wrap the edges in tape. You can also cover it with lacquer or add plexiglass on top to protect the design.
Clamp curved caul edges inwards so they align tabletop boards in the middle, then torque up the main clamps to draw the boards together. If the width of boards you’re using allow it, pre-glue boards for your tabletop in sections that are just narrow enough to fit within your thickness planer. Run these through the planer to clean and level the glue joints, then move back to clamps for final glue up. Working in stages like this reduces the number of glue joints you need to sand smooth and level later.
When sourcing materials from a renovation or job site be sure to have clear permission and wear the appropriate safety gear. Be aware that lead paint and asbestos may be mixed in with clean wood. Watch out for and pull nails out of material before loading in a car or truck so reclaimed wood will stack better. Be careful when working with items painted prior to 1979 as they may contain lead-based paint. Be sure to consult the EPA's Renovate Right: Important Lead Hazard Information for Families, Child Care Providers, and Schools pamphlet before disturbing any paint that could contain lead. Building materials produced before 1983 should also generally be tested for asbestos. Contact your local building official for exact requirements.
Are you redecorating your home but can’t seem to find the right table to complete your décor? Don’t worry too much because there are plenty of alternatives. There’s always a DIY project that can help you out. For example, we just found these beautiful DIY tables and we’re sure there are plenty more where these came from. Let’s take a look at them and see them closely.
Here’s an old woodworking adage I enjoy ignoring: “measure twice, cut once.” Honestly, I measure nonce and cut thrice. I often eyeball it. I use pieces I’ve already cut to measure what I need to cut. It’s not a great habit, but I prefer it to measuring everything. And the results usually aren’t that different. At least that’s what I tell myself. I ended up having to sand down the ends of the 2×12’s running the length of the table (where they meet the aprons) because they weren’t exactly the same length.
I’ve been doing a lot of remodeling on my house and this wristband has come in pretty handy. The magnets work very well and able to hold all the screws, washers, and bolts for the different projects I’m working on. The pockets are a great addition too for holding plastic items. In fact, I found it useful for holding a small pencil where I can have quick access to for marking measurements for cuts. Overall it’s a great quality wristband and would definitely recommend.
Photographer/filmmaker Brett Foxwell, who has expertise with both stop-motion and time-lapse techniques, created this very surprising video by shaving logs down layer-by-layer, then stitching still shots of the cross-sections together: WoodSwimmer from bfophoto on Vimeo.Writes Foxwell: I became fascinated with the possibilities of a sci-fi world based on the
If you can beg or borrow a pocket hole jig you dont have to predrill holes. I haven’t done a table top other than a workbench(Plywood!) but I have done cabinets and beds. The Kreg jig makes joining easy. A lighter stain colour would cut down on the grain marks, or a heavier application like an espresso stain. I will throw you a pic when I finish my table and show you what I mean.
No, it’s not a blood pressure tester. It’s an inflatable shim sold by Calculated industries. What in the world would you do with an Air Shim? Well, you could hold a window in position (by yourself) while setting the permanent shims, or prop up a door slab during installation without scratching the hardwood floor. Use it to align base cabinets or level appliances. You could even trick your big, burly buddy by betting him that your 10-year-old can pick him up off the ground… you will win that bet because the Air Shim is easy enough for anyone to pump and it holds up to 300-lbs. Deflate it as slow as you want for uber precision adjustments.
I've worn this apron in my studio/workshop several times now, and I really like it. It's more expensive than some, but the materials and construction are first-rate. I rarely give five stars, but the workmanship on this apron is impressive. The fabric is substantial and, although a bit stiff at present, comfortable to wear. The strap and grommet system is pretty clever, allowing a good fit for most, I would think. I'm a 5'-7" not-skinny woman, and I'm able to cross the straps at the small of my back and then tie them in front, so I'm guessing there would be plenty of strap length for bigger men. The straps sit comfortably on my shoulders. And all the pockets are great!
Rachel Teodoro and Holy-Craft.com, 2010-present. Unauthorized use and/or duplication of this material without express and written permission from this site’s author and/or owner is strictly prohibited. Excerpts and links may be used and up to one photo can posted, provided that full and clear credit is given to Rachel Teodoro and Holy Craft with appropriate and specific direction to the original content.