Because we were putting our new table cover over our existing table, we needed a rim that would hold it in place that was made of 1x2's. The 1x2's are an inch and half wide so adding two of those adds three inches overall to the length and width. I also added an extra 1/8" overall to both the length and the width so that there was a gap underneath so that the table could easily come on and off.

If planks are slightly cupped or twisted, have them planed at a local millwork shop or borrow a tabletop planer and tackle the job yourself. If planing yourself, first check planks for and remove nails and excess dirt*. Run planks though the planer, stripping a small amount of wood from each side as you plane. While the board is going through the planer, manually adjust the depth of the cut to compensate for irregular thickness (or twist) over the board’s length. You can hurt yourself or damage the board or planer if you do not manually adjust as you go. Keep running boards through the planer until the blade has lightly stripped each surface. Next, rip boards on a table saw to create straight edges; planks do not have to be identical in width.
My son asked for his DIY table to be painted green. But I can’t see myself making a wooden table and then painting the whole thing bright green. Sorry buddy, but it will still be great and green with painted layers. Thankfully, Dixie Belle has an amazing selection of colors! I will be painting the table using all of these gorgeous greens. The greens are:
Diablo's 3 piece Adjustable Cabinet Router Bit Set Diablo's 3 piece Adjustable Cabinet Router Bit Set features a rail and stile bit set and a Double Shear raised panel bit. Featuring TiCo carbide with titanium these bits provide a long cutting life and ultra-fine finish. Perma-Shield Diablo's high performance coating reduces friction and build-up on the bits. The ...  More + Product Details Close
This is a unique and cherished tool in my shop. 30 years ago my brother was a nuclear pipe welder at a federal submarine yard. He made this there and came home with it one day. The blade is submarine hull steel, Nickel Cobalt. I’ve never been able to sharpen it and it’s never really gotten dull. I had a diamond stone but quickly stopped using it as the diamond dust was being stripped off the stone. It has nostalgic and useful meaning to me.
There are lots of clear finishes. But for a combination of usability and durability, you can’t beat polyurethane. Oil-based poly, which dries slower than water-based, is best for beginners because it allows more working time. The other important difference is clarity: Water-based poly is absolutely colorless, while oil-based has an amber tone, which can be good or bad depending on the look you want.
Aside from the privacy it offers, a latticework porch trellis is a perfect way to add major curb appeal to your home for $100 or less. The trellis shown here is made of cedar, but any decay-resistant wood like redwood, cypress or treated pine would also be a good option. Constructed with lap joints for a flat surface and an oval cutout for elegance, it’s a far upgrade from traditional premade garden lattice. As long as you have experience working a router, this project’s complexity lies mostly in the time it takes to cut and assemble. Get the instructions complete with detailed illustrations here.
Diablo's 6-piece Starter Bit Set includes a variety Diablo's 6-piece Starter Bit Set includes a variety of profiles ideal for the beginning woodworker. Featuring TiCo carbide with titanium these bits provide a long cutting life and ultra-fine finish. Perma-Shield Diablo's high performance coating reduces friction and build-up on the bits. The bits kick-back reducing design allows for safer ...  More + Product Details Close
Here’s a traditional Swedish farm accessory for gunk-laden soles. The dimensions are not critical, but be sure the edges of the slats are fairly sharp?they’re what makes the boot scraper work. Cut slats to length, then cut triangular openings on the side of a pair of 2x2s. A radial arm saw works well for this, but a table saw or band saw will also make the cut. Trim the 2x2s to length, predrill, and use galvanized screws to attach the slats from underneath. If you prefer a boot cleaner that has brushes, check out this clever project.
**Important!  Be sure to pre-drill the holes for your screws before attaching the base to the table top!!  If you read the blog, then you know my table top ended up splitting, starting at a knot on the edge.  I’m pretty sure the cause of this was the fact that I attached the base to the top with screws without pre-drilling the holes, and I screwed right into a weak spot at the knot.  Learn from my very frustrating mistake, and don’t try to take short cuts!!
This super-strong and simple-to-build workbench is may be the project you've been looking for a long time. You have to select some free workbench plans to create yourself a working table in your shed that after you can use it when you are working on your projects and maybe it can provide you some extra storage, depends upon which plan you are choosing to DIY. 

Oh do I need this!! I have been trying to remove the damaged veneer from a great antique table, but after many hours I think I will have to give up and try a new top. I want to make sure I understand……If I have a good base on the table, I just cut the board lengths I need and glue to the origianl table top? Do I need to secure the new top with screws from the bottom? I think the boards will give this table a whole new life. I can’t wait to finish it. Thank you so much for being here TODAY!
When sourcing materials from a renovation or job site be sure to have clear permission and wear the appropriate safety gear. Be aware that lead paint and asbestos may be mixed in with clean wood. Watch out for and pull nails out of material before loading in a car or truck so reclaimed wood will stack better. Be careful when working with items painted prior to 1979 as they may contain lead-based paint. Be sure to consult the EPA's Renovate Right: Important Lead Hazard Information for Families, Child Care Providers, and Schools pamphlet before disturbing any paint that could contain lead. Building materials produced before 1983 should also generally be tested for asbestos. Contact your local building official for exact requirements.
Clamp curved caul edges inwards so they align tabletop boards in the middle, then torque up the main clamps to draw the boards together. If the width of boards you’re using allow it, pre-glue boards for your tabletop in sections that are just narrow enough to fit within your thickness planer. Run these through the planer to clean and level the glue joints, then move back to clamps for final glue up. Working in stages like this reduces the number of glue joints you need to sand smooth and level later.

One of the best stud finders you’ll ever use is the Franklin Sensors ProSensor 710. It’s unique in that there’s a whole bar of red lights that light up whenever it detects a stud. Unlike other sensors, which have a single light that stays on as it passes over the wood, the lights on the 710 tell you exactly where the wood stops and starts. No guesswork. Push a button, drag it over the wall and those hidden mysteries reveal themselves. You won’t even need to read the directions!


Screwdrivers are another must-have in the woodworker’s set of hand tools. Not only will you need Phillips and slot, or flathead screwdrivers, you’ll need star drivers and Torx drivers, too. A quality construction is vital to a good set of screwdrivers. So many of them are made out of soft metal, and the first time you put any “oomph” behind them, they strip out, becoming absolutely useless.
Here’s an old woodworking adage I enjoy ignoring: “measure twice, cut once.” Honestly, I measure nonce and cut thrice. I often eyeball it. I use pieces I’ve already cut to measure what I need to cut. It’s not a great habit, but I prefer it to measuring everything. And the results usually aren’t that different. At least that’s what I tell myself. I ended up having to sand down the ends of the 2×12’s running the length of the table (where they meet the aprons) because they weren’t exactly the same length.
Begin by cutting off a 10-in. length of the board and setting it aside. Rip the remaining 38-in. board to 6 in. wide and cut five evenly spaced saw kerfs 5/8 in. deep along one face. Crosscut the slotted board into four 9-in. pieces and glue them into a block, being careful not to slop glue into the saw kerfs (you can clean them out with a knife before the glue dries). Saw a 15-degree angle on one end and screw the plywood piece under the angled end of the block.

Diablo's 3 piece Adjustable Cabinet Router Bit Set Diablo's 3 piece Adjustable Cabinet Router Bit Set features a rail and stile bit set and a Double Shear raised panel bit. Featuring TiCo carbide with titanium these bits provide a long cutting life and ultra-fine finish. Perma-Shield Diablo's high performance coating reduces friction and build-up on the bits. The ...  More + Product Details Close


No sadly, as I mentioned above, my table top ended up splitting, starting at a knot on the edge and going clear across the top (pre-drill those holes!!!), so I had to come up with another solution.  I didn’t want to go to the trouble of making another table top like this one, so I did a much easier and quicker solution…stain-grade plywood with decorative moulding attached to the edges. 
Limited floor space is a problem in most shops. However, that’s no longer an excuse for kicking up a bunch of dust without a dust collection system as Grizzly now makes a wall-mounted dust collector. It’s equipped with a powerful 1-HP motor prewired for 120V. It features a canister filter with six times the surface area of a standard bag-filter, yet it takes up less space. The filter is easy to keep clean with the hand crank filter-cleaning brush.

Work at a place where you’re required to wear a steel-toe boot? Then listen up. Wolverine just introduced a new boot that’s much more comfortable but still offers solid impact protection. Instead of steel, CarbonMAX boots have a protective cap made of carbon nanotubes, making them lighter and thinner. And if anyone knows about making comfortable work boots, it’s Wolverine—they’ve been making them for more than 130 years.

These unique clamps will save you time and aggravation in too many ways to list! MatchFit clamps slide anywhere along a groove routed with a common 1/2" - 14 degree dovetail bit and leave one surface of your work clear of obstructions. Use these clamps to create customizable clamping tables and for attaching table extensions, sub fences, stop blocks, hold downs, and more to your machinery and work tables. Imported.

Turning over the sturdy tabletop, I felt a thrill of vindication. Clearly, it wasn’t a mistake in the end to use all three stains for the same project. Before I could consider the job done, though, I would need to apply sealer—Minwax Helmsman Spar Urethane—to protect the wood from moisture, UV rays, and the wear and tear of day-to-day life. This was my first time experimenting with a spray-application sealer, and I loved it. Obviously, it’s important to have proper ventilation in your work area, and you’ve got to shake the can vigorously before spraying, but so long as you remember the basics, spraying couldn’t be more straightforward. Holding the Helmsman Spar Urethane can about a foot from the surface, spray in a series of even strokes, always in the same direction, until you’ve completed the first coat. Let the sealer dry for about four hours before applying any additional coats, and for best results, sand the entire surface before each application of a new layer.
If you have already graduated from college or university and are searching for a good job, you need to have a persuasive resume to impress your future employer. Our team of writers who provide this type of assistance will be glad to make a job-winning resume for you. If you need a cover letter, we can help with it too. Tell our expert about your experience, skills, and goals, and become a step closer to the job of your dream.
Creating a classic toy: One of my favorite shop projects is to create children’s cedar building blocks from rough Tennessee red cedar. These came about after I built my first Adirondack chairs and I had a large amount of scrap wood left over. Our first granddaughter had just been born and we decided to build a set of building blocks. Since that first set of blocks was made I’ve delivered hundreds to young children all across the country. Hearing the stories of the kids playing with these for hours and seeing the joy on their faces is what it’s all about. *DISCLOSURE: Some of the links below are affiliate links. If you chose to click through and make a purchase I will earn a commission but there is no additional cost to you. It helps compensates the business for the time spent creating these posts. THANK YOU! Start with Rough Cut Cedar These blocks start with rough 2×4 and 2×6 cedar lumber purchased from my local cedar mill. I use my Ridgid Power Tools Surface Planer to bring the wood into smooth milled lumber. Over to the SuperMax Drum Sander to sand the wood as much as possible. The goal is make sure the wood is as soon as glass. Then the wood goes into my Ridgid table saw to be milled into ¾ x ¾, 2 x 2 and ¾ x 2. Once the pieces are cut to proper width its over to the Grizzly Band saw to cut the blocks to length. I tried to do this on my sliding miter saw, but found I could not control the blocks well enough and the saw blade would cause them to either get jammed or fly across the shop and be ruined. Block Sizes These blocks come in a number of rectangle and square sizes. ¾ x ¾ x 2”, 4” and 6” ¾ x 2 x2’, 4” and 6” 1 ½ x1 ½ x1 ½ 2 x2 x 2”, 6” Final Step by Hand The last step is to take them to the Ridgid Oscillating Sander and round over the edges and corners to keep them safe. Because we handle them multiple times it gives is the opportunity to clear out any misfits and chipped blocks. Watch the process here. At one point we were coating them with a finish used for salad bowls but they were hard to dry without leaving ridges from the drying racks or drips that needed to be sanded off. It was recommended/suggested by a number of mothers that we not put anything on them. The beauty of these blocks is they hold the smell and are safe to play with. They provide hours of fun when stacking and building. I have watched the little ones learning how to pick things up grab and hold them. Available to purchase on Etsy Interested in having your own set? We have a limited amount available for Christmas 2018 with or without the hand made wooden
For all of your wood cabinetry and joinery tools and supplies, Infinity Cutting Tools has got you covered. We offer joinery tools and accessories for making box joints, finger joints, pocket holes, dowel joinery, dovetails, and mortise-and-tenon joinery. When it comes to installing cabinet hardware like knobs, pulls, and hinges, check out our cabinet hardware installation solutions.
Simply brilliant. Why didn’t I think of this? So we have a nearly 100 year old house. There is always something that needs repair. Thanks to whoever invented this little guy! No more mouth full of nails or screws. No more climbing up and down the ladder to get the damn screwdriver I dropped. Probably won’t hold your 16 oz claw hammer but other than that it is perfect. I love this. Highly recommend. Thanks for reading
There’s a lot of space above the shelf in most closets. Even though it’s a little hard to reach, it’s a great place to store seldom-used items. Make use of this wasted space by adding a second shelf above the existing one. Buy enough closet shelving material to match the length of the existing shelf plus enough for two end supports and middle supports over each bracket. Twelve-inch-wide shelving is available in various lengths and finishes at home centers and lumberyards.
Now that you have the final dimensions for the table top, you need to choose which boards you want to use.  Because we don't have a table saw and we wanted to keep this project simple and not cut any boards lengthwise, we {and by we, I mean my husband} plugged and chugged different board sizes into his calculator to find the perfect equation. We ended up using seven 1x6 boards for the width and on the two end caps we used 1x8's. Remember, a 1x6 is not six inches wide, it's five and a half, and a 1x8 is seven and a quarter inches wide. When you are doing your math to figure out what boards you need, remember that the nominal size {1x4, 1x6, 1x8, etc} is not the actual measured dimension of the board.
Creating a classic toy: One of my favorite shop projects is to create children’s cedar building blocks from rough Tennessee red cedar. These came about after I built my first Adirondack chairs and I had a large amount of scrap wood left over. Our first granddaughter had just been born and we decided to build a set of building blocks. Since that first set of blocks was made I’ve delivered hundreds to young children all across the country. Hearing the stories of the kids playing with these for hours and seeing the joy on their faces is what it’s all about. *DISCLOSURE: Some of the links below are affiliate links. If you chose to click through and make a purchase I will earn a commission but there is no additional cost to you. It helps compensates the business for the time spent creating these posts. THANK YOU! Start with Rough Cut Cedar These blocks start with rough 2×4 and 2×6 cedar lumber purchased from my local cedar mill. I use my Ridgid Power Tools Surface Planer to bring the wood into smooth milled lumber. Over to the SuperMax Drum Sander to sand the wood as much as possible. The goal is make sure the wood is as soon as glass. Then the wood goes into my Ridgid table saw to be milled into ¾ x ¾, 2 x 2 and ¾ x 2. Once the pieces are cut to proper width its over to the Grizzly Band saw to cut the blocks to length. I tried to do this on my sliding miter saw, but found I could not control the blocks well enough and the saw blade would cause them to either get jammed or fly across the shop and be ruined. Block Sizes These blocks come in a number of rectangle and square sizes. ¾ x ¾ x 2”, 4” and 6” ¾ x 2 x2’, 4” and 6” 1 ½ x1 ½ x1 ½ 2 x2 x 2”, 6” Final Step by Hand The last step is to take them to the Ridgid Oscillating Sander and round over the edges and corners to keep them safe. Because we handle them multiple times it gives is the opportunity to clear out any misfits and chipped blocks. Watch the process here. At one point we were coating them with a finish used for salad bowls but they were hard to dry without leaving ridges from the drying racks or drips that needed to be sanded off. It was recommended/suggested by a number of mothers that we not put anything on them. The beauty of these blocks is they hold the smell and are safe to play with. They provide hours of fun when stacking and building. I have watched the little ones learning how to pick things up grab and hold them. Available to purchase on Etsy Interested in having your own set? We have a limited amount available for Christmas 2018 with or without the hand made wooden
The Milwaukee REDSTICK can be used to screed, smooth, and level. Once you’re done, the level is preposterously easy to wipe clean. The REDSTICK also has all the great features you would expect from a Milwaukee level. SHARPSITE Vial Technology makes the magnified bubble easy to read and the REDSTICK’s magnesium core keeps the level from breaking down. The Milwaukee REDSTICK Concrete Levels are available in 24-in., 48-in. and 72-in. lengths starting at $99.99.
3. Sand off the corners of the long edges of the top side. Another personal preference. When you glue the boards together, this will help break up the top so that it looks like it was made of wooden planks instead of one solid slab of wood. You get the appearance of grooves without fussing with actual grooves, shifting boards, uneven gaps, and glue seepage. Check out the photos of the finished boards above or the one below after step 6 to see the “grooves.”
For an artisanal look, you can use woodworking hand tools. These are easy to use, lightweight and require no batteries or power cords to operate. Many hand tools are covered by multi-year or even lifetime warranties for extra protection and value. Set up your pieces with the most expertly crafted woodworking hardware, such as hinges, pulls and knobs to create a final product that you can give as a gift, sell or just display proudly.
Touch ‘n Foam’s Gel Foam Subfloor Adhesive might make you want to chuck your caulking gun for good. It comes in a can and dispenses just like the spray-foam insulation everyone is familiar with. It lays down a bead way faster than tube adhesives but without the endless, wrist-busting trigger squeezing. And you’ll be able to keep working up to 10 times longer without stopping to reload. There’s no downtime due to wet or frozen lumber, and the can is reusable up to 15 days. To use Touch ‘n Foam Subfloor Adhesive, you’ll need an applicator gun (the same one used for expanding foam). There’s also a 46-in.-long barrel for the applicator gun that will save your back from a whole lot of bending over.
Here’s an old woodworking adage I enjoy ignoring: “measure twice, cut once.” Honestly, I measure nonce and cut thrice. I often eyeball it. I use pieces I’ve already cut to measure what I need to cut. It’s not a great habit, but I prefer it to measuring everything. And the results usually aren’t that different. At least that’s what I tell myself. I ended up having to sand down the ends of the 2×12’s running the length of the table (where they meet the aprons) because they weren’t exactly the same length.
A few days back, I was searching for some cool DIY plans. So, I got to work and ended up coming up with some easy to follow project and an awesome new ice chest cooler to have out on the deck! It was going to be perfect for summer hangouts and barbecues. It was a fun and practical plan to work on and I know you will have fun tackling select a design from this plan and start building your own. Enjoy learning how you can build a rustic cooler also sing the video tutorial and source tutorial plan!
×