From the source tutorial, you can get illustrates to the instruction about the plan. Everything is fairly described as diagrams, images, the list of supplies and tools need etc. The process to this plan is very easy to understand and follow for if you are having some basic woodworking knowledge. Make sure to collect all the supplies you need before you start with the project. You may even ask any question directly in the comment section of the tutorial post and also comment the images of your final product if you have completed it. Either way, I hope that you will manage to build this one nicely.​
Pallet tables are very common and very easy to make. To make it you’ll need about half of a wood pallet. Decide the dimensions for the table and then remove some of the boards and cut them to size. Reattach them using nails and then sand the table. Then you can stain or seal the wood if you want. At the end, you can either add legs, casters or leave the table as such.{found on hernewleaf}.
You can’t beat spray foam for sealing around windows and doors or sealing large gaps and cracks in old house walls, foundations and attics, but how often have you run a can empty when you were so close to being finished? And how disappointing is it to use a partial can, knowing you’ll have to throw the rest away? If you’re a regular spray foam user, it might be time to step up to a foam dispensing gun.
The Milwaukee REDSTICK can be used to screed, smooth, and level. Once you’re done, the level is preposterously easy to wipe clean. The REDSTICK also has all the great features you would expect from a Milwaukee level. SHARPSITE Vial Technology makes the magnified bubble easy to read and the REDSTICK’s magnesium core keeps the level from breaking down. The Milwaukee REDSTICK Concrete Levels are available in 24-in., 48-in. and 72-in. lengths starting at $99.99.

Carefully lay the top down and attach pipe clamps at roughly 1' intervals. Slowly tighten each pipe clamp in a consistent fashion until the gaps disappear. Small amounts of glue can be removed when dry; scrape up any puddled glue with a plastic putty knife. To minimize sanding later, avoid working glue into the top of the wood. Let the top set overnight.
To save money, we keep the temp in our shop down low when we’re not in it and crank up the heat when we return. But even when the air temperature hits 70 degrees F, the concrete floor is still Minnesota-cold. We tried a space heater under the bench, but it broiled the shins and still left us with cold feet. So we recently bought a foot-warming mat, and now our feet stay toasty warm. Plus, it uses a fraction of the electricity and is a lot safer than a space heater. The mat is produced by Cozy Products. The good folks over at Cozy suggest putting a chunk of cardboard underneath it if you use it on flooring that could fade from the heat, like carpet or wood.

Clamp curved caul edges inwards so they align tabletop boards in the middle, then torque up the main clamps to draw the boards together. If the width of boards you’re using allow it, pre-glue boards for your tabletop in sections that are just narrow enough to fit within your thickness planer. Run these through the planer to clean and level the glue joints, then move back to clamps for final glue up. Working in stages like this reduces the number of glue joints you need to sand smooth and level later.


Or if you are in the search for a protectant that is specifically for woodworking tools, then you should check out the Restore Blade and Bit Cleaner 500. Not only is this cleaner one of the best woodworking accessories, it’s also environmentally friendly and safe to breathe in while using. This cleaner is the perfect companion for circular saws, miter saws, router bits, drill bits, as well as a variety of woodworking tools. While protecting your tools from rust and corrosion, it’s liquid form will not damage any wood materials that you may be working on at the time.
Or if you are in the search for a protectant that is specifically for woodworking tools, then you should check out the Restore Blade and Bit Cleaner 500. Not only is this cleaner one of the best woodworking accessories, it’s also environmentally friendly and safe to breathe in while using. This cleaner is the perfect companion for circular saws, miter saws, router bits, drill bits, as well as a variety of woodworking tools. While protecting your tools from rust and corrosion, it’s liquid form will not damage any wood materials that you may be working on at the time.
Just a little nitpick on the tape measure blurb. The hook should not be completely tight. It should move in and out about a 1/16th or the thickness of the hook. This way you get an accurate measurement whether you hook a part to measure or bump up to it. If you want more accurate measurements with a tape measure, “burn” an inch instead of hooking or bumping the part. Just line up what you want to measure with the 1″ mark and subtract that inch from the final measurement.
A super simple iPad Dock/stand made out of a single block of wood features an angled groove which gets to support the tablet device and a cut in a hole to revise access to the home button of your iPad. It’s possible to drill an access channel in the stand through which you can run a charging cable, although this mini stripped back iPad stand may have very limited functions.
Now it’s time for one of the trickiest parts–attaching the side rails to the legs. I did this part on top of the tabletop, because it was the flattest surface I could find. We got the rail perfectly straight and I had my wife stand on it to keep it steady as I drilled the pilot hole through the leg and into the rail. Then we screwed in the 6″ lag screws. And I just about broke my arm trying to use a power drill with a socket to do this.
As your interest in woodworking grows, you’ll want to subscribe to a woodworking magazine. This will help feed your new found obsession with articles on tools, techniques, and woodworking plans. As a print magazine subscriber you’ll also gain access to their database of plans on their websites. Popular magazines include, Woodworkers Journal, Fine Woodworking, and Popular Woodworking.
Crisp, tight joints are key to any great tabletop, and this is where the jointer comes in. Get help supporting boards longer than about five feet as you work. Also, if some joints don’t come together tightly, despite your best jointing efforts, try moving the boards to new locations if grain patterns permit. Some edges just naturally fit together more tightly than others. Don’t own a jointer? Pieces of planed lumber sometimes fit together just fine without jointing. Try different boards as neighbours to see which ones get along the best.
After your table is pieced together, you will flip it over {remember, you've been working on it upside down} and sand it.  My husband isn't a big fan of the planks and worried about cups and plates getting stuck and spilled on the uneven parts of the boards, so he went to town with the sander. You can keep more of the plank look by sanding it less.
Here’s another example of a stenciled tabletop.  Remarkably, this table was destined for the dump when Pretty Handy Girl pulled it from a dumpster.  With a stencil, primer and paint, some distressing, glazing and sealing, she gave this beauty a second life – one in which it looks like it came directly from old world Scandinavia. // Pretty Handy Girl
The client then explains the furniture he wants. In detail, he describes the dimensions, moving parts, the features of the furniture and his budget for such work. The woodworker takes note of the information and gives the client an estimate. After a day or two, the woodworker gives a preliminary design of the item the customer wishes to have. The design could be revised if the customer wishes to alter it. The first exchange of money, the payment of the design fee, usually happens here.
Drill four 5/8-in.-dia. 1/2-in.-deep holes on the large disc?inside the traced circle?then use 5/8-in. dowel centers to transfer the hole locations to the underside of the small disc. Drill four 1/2-in.-deep holes on the underside of the small disc and a 1/2-in.-deep hole in the center of the top for the dowel handle. Glue in the dowels to join the discs, and glue in the handle. We drilled a wood ball for a handle knob, but a screw-on ceramic knob also provides a comfortable, attractive grip.
The most commonly purchased claw hammer is the 20 oz. size. It’s heavy enough to easily drive nails but easily manipulated when pulling nails. While wooden handles are picturesque, they may not stand up to the strain if you have to pull a lot of nails. Hammers with a steel handle, or even fiberglass, will be stronger. However, these won’t absorb the vibrations from driving nails the way a hickory handle will. You’ll also need to make sure the fiberglass and metal handles have a rubberized grip for control and comfort. If you’re going to be driving a lot of nails, the wooden handled hammer will be better for reducing stress on your hand, and wrist, too.
Oh do I need this!! I have been trying to remove the damaged veneer from a great antique table, but after many hours I think I will have to give up and try a new top. I want to make sure I understand……If I have a good base on the table, I just cut the board lengths I need and glue to the origianl table top? Do I need to secure the new top with screws from the bottom? I think the boards will give this table a whole new life. I can’t wait to finish it. Thank you so much for being here TODAY!

Building a bookcase or bookshelf is a fairly simple woodworking plan that you can get done in just a day or two. This is also a low-cost project as well and since the project idea is free, you don't have to worry about busting through your budget. Just follow the simple steps in the tutorial and enjoy your own company building a simple bookcase on this weekend.

We recently upgraded a wheelbarrow with Simply Dump It pivoting handles. They slid right over the handles and took about five minutes to install. If you’re tall, you probably hunch over when you roll your wheelbarrow around the yard so you don’t end up nose-diving the wheel guard/brace into the ground, resulting in messy spills and the occasional expletive. The Simply Dump It handles raise the grip location a few inches, which lowers the handles, which in turn raises the front wheel brace. The handles not only prevent sudden stopping syndrome but also make the wheelbarrow easier to control, especially on rough terrain. And the pivoting action all but eliminates the awkward torque on your wrists when you empty the wheelbarrow. You can get Simply Dump It handles online.


Do you enjoy splinters or cuts from metal flashing? Nope me neither. THESE GLOVES ARE THE SHIZ NIT! I have yet to get a splinter when handling my rough-edged plywood. Not only are they cheap but extra reliable. Mom these gloves are for you (My poor mom always gets splinters when she helps me DIY). This is one of the unique tools you’ll be happy you own.
Clean wooden gutters of any loose debris and cut to a manageable length. Miter down to form an approximately 40" x 94" rectangle. Coat the corners with wood glue and fasten together with 15-gauge finish nails. If miters are tight 45-degree cuts, box should be square. Double check diagonal measurements before fastening completely. The two diagonal measurements should be as close to equal as possible.
The Story of the Farmhouse Table with a Race Track While working my day job one of my managers came to my desk and said “I need your help”. Come to find out she ordered a farmhouse table and bench on Etsy. However the person she ordered it from fell off the face of the earth and left her without a table or her money (Etsy made good on it for her). The reason she ordered the table was because of the three legged bench. She has a young son and was concerned that he would turn over a two legged bench. This one appeared to give her the stability that she wanted. My reply, “I can help!” After seeing the picture of the table she ordered I told her to give me a few days and I could find her an alternative. So I went out to one of my trusted bloggers, Rogue Engineer and found the table I wanted to build. Please check out his site and follow him on social media. After getting her approval of the style and layout, we agreed on a price and some minor adjustments to the plans. She only wanted a 7 foot table and she only wanted one bench, but that bench needed a third leg. So I made the size adjustments and quoted the table. Now the “Curve” A couple of days after we agreed on the project my client called and said she had an idea on the way to work. She needed to find a way to get her son to the dinner table. “Can I add a 1½” wide by 1/8th inch deep race track around the top of the table?” After I caught my breath and recovered I gave her some alternative ideas to avoid creating a race track into what I knew was going to be a beautiful table. She was convinced this is what she wanted, so I said well, this is why we call ourselves Bayne CUSTOM Woodworking. So I agreed and then the adventure began. The Build Instead of recreating what Rogue Engineer already did I will refer you to his free plans on his site. See the link in the opening paragraph.  He will provide the materials list needed. Below I will outline the changes I made and how I built the table and bench. While not huge changes, there are some that I made to meet the client’s requests and some to add my own unique style. The plans call for a table that is 110” while I made mine to fit the client request of 84”. Because I trimmed my boards I ended up with a 40” wide top instead of a 42” wide. She wanted only one bench so I made an 80” bench with 3 legs instead of the 2 legged bench. Let me also state up front that I rarely, if ever, use pine to build anymore, but I did use it on the job because
This tool is specialized for the task of making shingles. The strange name comes from the antiquated word "froward," which means "away," in reference to the direction that the tool cuts. To use it, place the froe, blade down, on the edge of a log length, then hit the top of the blade with a wooden club, forcing the froe into the log. Next, pull the handle toward you and pry off a thin slice of the log. Voilà... shingle! Since buying a box of square-edged shingles is significantly less effort than making each and every one by hand, this tool has long since passed its heyday. But it still can be used to build up the kindling pile.
Ridgid has a new C-style close-quarter tubing cutter that slices through both 1/2-in. and 3/4-in. tubing, which means one less tool to carry and fumble around for. The cutting wheel is spring loaded so it needs no adjustment as you spin the cutter, and the outside surface has screwdriver slots for getting leverage in tight spaces. The 1/2 – 3/4 Rigid tubing cutter costs $32 and is available at plumbing supply stores and online retailers.
The Story of the Farmhouse Table with a Race Track While working my day job one of my managers came to my desk and said “I need your help”. Come to find out she ordered a farmhouse table and bench on Etsy. However the person she ordered it from fell off the face of the earth and left her without a table or her money (Etsy made good on it for her). The reason she ordered the table was because of the three legged bench. She has a young son and was concerned that he would turn over a two legged bench. This one appeared to give her the stability that she wanted. My reply, “I can help!” After seeing the picture of the table she ordered I told her to give me a few days and I could find her an alternative. So I went out to one of my trusted bloggers, Rogue Engineer and found the table I wanted to build. Please check out his site and follow him on social media. After getting her approval of the style and layout, we agreed on a price and some minor adjustments to the plans. She only wanted a 7 foot table and she only wanted one bench, but that bench needed a third leg. So I made the size adjustments and quoted the table. Now the “Curve” A couple of days after we agreed on the project my client called and said she had an idea on the way to work. She needed to find a way to get her son to the dinner table. “Can I add a 1½” wide by 1/8th inch deep race track around the top of the table?” After I caught my breath and recovered I gave her some alternative ideas to avoid creating a race track into what I knew was going to be a beautiful table. She was convinced this is what she wanted, so I said well, this is why we call ourselves Bayne CUSTOM Woodworking. So I agreed and then the adventure began. The Build Instead of recreating what Rogue Engineer already did I will refer you to his free plans on his site. See the link in the opening paragraph.  He will provide the materials list needed. Below I will outline the changes I made and how I built the table and bench. While not huge changes, there are some that I made to meet the client’s requests and some to add my own unique style. The plans call for a table that is 110” while I made mine to fit the client request of 84”. Because I trimmed my boards I ended up with a 40” wide top instead of a 42” wide. She wanted only one bench so I made an 80” bench with 3 legs instead of the 2 legged bench. Let me also state up front that I rarely, if ever, use pine to build anymore, but I did use it on the job because
Now, the project starts to get really interesting. While I knew that I would use pocket-hole joinery (my latest obsession) to assemble the tabletop, I couldn’t decide how to finish the wood. There were three different cans of Minwax Gel Stain on my shelf, in three different colors—Hickory, Cherrywood, and Honey Maple. In my head, I could make a credible argument in favor of each one. And though it would have helped to know where the table would eventually go, that was another question I couldn’t answer. Then it hit me: Rather than choose one stain, why not use them all? After all, I was constructing the tabletop from scraps, so it was going to have a homemade, mosaic look no matter what. In the end, using multiple stains would emphasize the rustic effect the table was going to achieve. Perfect! From there, having fought my way to a project plan, the rest came easy. Read on to see how I built the tabletop, then stained and sealed it with Minwax.
Look at the amazing masterpiece Domestic Imperfection made out of her plain Jane dining table!  Using a stencil and white paint, you can create this design or similar, then tone it down and make it look slightly aged by staining the wood right over the top of the painted design!  Very clever stenciled and stained table redo. // Domestic Imperfection

Do you want to use an oil stain, a gel stain, a water-based stain or a lacquer stain? What about color? Our ebook tells you what you really need to know about the chemistry behind each wood stain, and what to expect when you brush, wipe or spray it on. It’s a lot simpler than you think! This is the comprehensive guide to all the varieties of stain you will find at the store and how to use them.
The end grain of wood soaks up finishes and often turns much darker than the face grain. Check for this on your test block. If you get an ugly result, pretreat the end grain with a dose of finish that will limit absorption (wood conditioner, sanding sealer, shellac or polyurethane thinned 50 percent). Apply the treatment with an artist’s brush and be careful not to slop onto the face grain. 

Here’s an old woodworking adage I enjoy ignoring: “measure twice, cut once.” Honestly, I measure nonce and cut thrice. I often eyeball it. I use pieces I’ve already cut to measure what I need to cut. It’s not a great habit, but I prefer it to measuring everything. And the results usually aren’t that different. At least that’s what I tell myself. I ended up having to sand down the ends of the 2×12’s running the length of the table (where they meet the aprons) because they weren’t exactly the same length.
We no longer have that problem because we picked up a set of Mag Shims from FastCap. Mag Shims are 1/8-in. magnetic spacers. If you need a blade height of 7/8 in., simply stack seven spacers, and raise the blade to match. They also work great for setting the depth on router bits and drill presses. We stick them right to the backside of the fence, so they’re always at hand and never get lost.
PROCESSING NOTES: No matter how easy I have tried to make following these media center plans and constructing them, if you find it overwhelming to attempt the project or operate the basic tools necessary for completion, get help. Contact your local supplier to see if sheet goods can be ripped to fit your car trunk. The possibility of ordering all the parts ready for assembly is also available. Most importantly, when you set off to build your project, help is only an email message away.
If your skill level is not yet high enough to tackle a difficult design, you need to get more practice by doing more basic designs, which teach you the techniques you will need for the harder jobs. It is rightfully said practice makes man perfect and you should do lot of practice to master this skill.
If you can beg or borrow a pocket hole jig you dont have to predrill holes. I haven’t done a table top other than a workbench(Plywood!) but I have done cabinets and beds. The Kreg jig makes joining easy. A lighter stain colour would cut down on the grain marks, or a heavier application like an espresso stain. I will throw you a pic when I finish my table and show you what I mean.

CHANNELLOCK thinks that they’ve got the solution to help unclutter your tool belt. The new CHANNELLOCK Reversible Jaw Adjustable Wrench is just like a normal wrench, but also features a part of the jaw with angled teeth. All you have to do is reverse the jaw and the teeth will let you get a tight grip on objects that that a regular wrench would just slide off of. These new wrenches are available in 6, 8, 10 and 12-inch sizes. They are available in most major hardware retailers in the US and Canada. Price and availability will vary by retailer.


Verdict : Ted’s product is EXTREMELY extensive with 16k plans and there are tons of projects to choose from. Not every woodworker online loves it, but it’s cheap and perfect for every level of experience, I love it because this is basically the only resource I need. I highly suggest it. They also offer a really solid money back guarantee if you don’t like it after all.
In stock expedited shipments will ship the same day, or the next business day for orders placed on a weekend, if the order is placed before 12 PM Central Time. Non-expedited orders are processed for shipment within two business days of payment verification, excluding holidays. You will receive a shipping confirmation e-mail once your order has shipped. The e-mail will provide your tracking number and link to the shipping carrier’s tracking page.
I purchased these gloves for work, which involves handling and packing several (thousand) books everyday. When they arrived, they were a little too big for my smallish hands. I figured I would use them anyway to spare my sore fingers, and for the week I used these my hands were safe and papercut-free! The grip dots were secure and helped to grip even thin sheets of paper. The fingers bunched up a bit, but that's to be expected from oversized gloves.
There are YouTube videos that show how to attach tabletops using both of these tried and true methods. If you don't have a router or a biscuit joiner to make the holes for the z-fasteners, you can always use a drill. For the figure-8's, you need to recess them so they're flush with the apron...so for that, you would need to use a router. If that's not somethig you can do, I suggest sticking with the Z-fasteners. Best of luck!
Do you have older 18V DeWalt tools that are still near and dear to your heart but need new batteries? Consider firing up those old tools with 21st century technology. Now, 18V tools can be run on powerful 20V lithium Ion batteries with DeWalt’s new battery adapter. The adapter slides into the tool and the battery hooks onto the adapter. It works on most 18V DeWalt tools but not all. It’s sold two ways: the adapter alone (DCA1820), or the adapter with two compact 20V, 2.OAh batteries and charger. Now you’ll be able to hold on to your favorite cordless reciprocating saw forever!
Carefully lay the top down and attach pipe clamps at roughly 1' intervals. Slowly tighten each pipe clamp in a consistent fashion until the gaps disappear. Small amounts of glue can be removed when dry; scrape up any puddled glue with a plastic putty knife. To minimize sanding later, avoid working glue into the top of the wood. Let the top set overnight.
In stock expedited shipments will ship the same day, or the next business day for orders placed on a weekend, if the order is placed before 12 PM Central Time. Non-expedited orders are processed for shipment within two business days of payment verification, excluding holidays. You will receive a shipping confirmation e-mail once your order has shipped. The e-mail will provide your tracking number and link to the shipping carrier’s tracking page.
The owners, webmasters, administrators, authors and editors, expressly disclaim all and any liability to any person, whether a user of this website or not, in respect of anything and of the consequences of anything done or omitted to be done by any such person in reliance, whether whole or partial, upon the whole or any part of the contents of this website. Please exercise caution when working with any tools or machinery. Follow common safety rules and precautions as outlined in any manuals related to the equipment being used. If advice or other expert assistance is required, the services of a competent professional person should be sought.
Reclaimed Wood from Corn Crib HOW TO DESIGN AND BUILD AN ENTRY WAY COAT RACK AND BENCH There was a door in granddad’s home the client wanted to preserve and wondered, if they provided the wood, could I build an entryway coat rack and bench using the door as part of the build. The wood they wanted to provide, well, that was from the family owned Tennessee corn crib that had been torn down and they didn’t want to lose the wood or the memories. Not only was this a corncrib but it was eventually used by the great grandchildren as a play house. So for the client there are as many memories in this build as there are colors. THIS PROJECT TRULY DEFINES THE “CUSTOM” in BAYNE CUSTOM WOODWORKING. I spent some time to design a simple layout in @sketchup_official so the client could approve the idea I had in mind. The wood showed up in two deliveries so we stacked it outside because this was the first time I worked with barn wood. I did not want to introduce possible termites to my shop. So my first call was to my pest guy asking how I would treat the wood for termites. Much to my relief he said I had nothing to worry about. This was “real” wood! Not nominal at all, nominal is how we buy our wood at a local hardware store. Where a 2×4 is actually 1 ½  x 3 ½ . These 2×4’s were at least 2”x4”’s if not more and were hard, heavy and dusty, did I say heavy? After cutting to length on my handy @DewaltTough miter saw, I had to take them to my @ridgidpowertools table saw and square up the bottoms only.  I was very careful not to lose any of the original saw marks and character because that would ruin the entire purpose. For someone who likes clean, crisp edges, this was a bit of a challenge. I used @kregjig Kreg Jig® K4 Master System to join all the pieces of the base, the seat frame and the supports to join the two together. I was very careful to hide all of the pocket holes so they could not be seen from any angle. I used Titebond Products original interior wood glue to join all the pieces together. The next item was to assemble the back which included grandad’s door as the center piece. The door was only 71 ½ tall which determined the overall height of the project. Part of this back also includes two live edge pieces that we picked to use as the “L” shaped wings or side walls. The door measured 24” which left me with 6” on each side to make up the final size of 36”. So I chose two of the straightest boards that were closest to 6” and cut them to width so as not to waste any wood or lose any character. I used the Kreg Jig® K4 Master System 

Do you enjoy splinters or cuts from metal flashing? Nope me neither. THESE GLOVES ARE THE SHIZ NIT! I have yet to get a splinter when handling my rough-edged plywood. Not only are they cheap but extra reliable. Mom these gloves are for you (My poor mom always gets splinters when she helps me DIY). This is one of the unique tools you’ll be happy you own.
This tool is specialized for the task of making shingles. The strange name comes from the antiquated word "froward," which means "away," in reference to the direction that the tool cuts. To use it, place the froe, blade down, on the edge of a log length, then hit the top of the blade with a wooden club, forcing the froe into the log. Next, pull the handle toward you and pry off a thin slice of the log. Voilà... shingle! Since buying a box of square-edged shingles is significantly less effort than making each and every one by hand, this tool has long since passed its heyday. But it still can be used to build up the kindling pile.
Let’s start with perhaps the most basic tool in every household – the claw hammer. The claw on one side of the head should be well counterbalanced by the finished head, which should be somewhat rounded. The other kind of head is the waffle-head. Most commonly used in construction, it leaves a distinctive waffle mark on the wood when you drive the nail. This, of course, is not the proper nail for woodworking.
There are lots of clear finishes. But for a combination of usability and durability, you can’t beat polyurethane. Oil-based poly, which dries slower than water-based, is best for beginners because it allows more working time. The other important difference is clarity: Water-based poly is absolutely colorless, while oil-based has an amber tone, which can be good or bad depending on the look you want.
×