Adirondack Chairs in Tennessee Cedar Wood Growing up in Central New York and spending years in the Adirondack Mountains, I grew up seeing all types of Adirondack chairs. But it was not until I moved to middle Tennessee that I attempted to build Adirondack chairs myself. I found plans that gave me the basic design to build the adult chairs. I made some adjustments in order to fit them into my style and the type of wood that I have available. I found a cedar mill within an hour of my shop that allows me to purchase rough cut lumber. Because of the nature of rough lumber I am buying wood that is actually thicker, wider and longer than wood purchased at a brick front store.  Where a nominal 2”x 4”x 96” bought at a local lumber store is actually 1.5 x 3.5 x 96. The cedar I purchase is 2 ¼ x 4 ¼ x 102 inches. Once run through the surface planer to clean up the roughness and sanded, I am able to build with actual 2” x 4” or 2” x 6” lumber. This makes the chairs heavier, sturdier and more durable. Because of the size of the wood I assemble the legs and main supports with 3/8” carriage bolts. The arms, seat boards and backs are all assembled with 2” to 3” exterior screws. I predrill all the holes prior to inserting any screws. I do this because cedar, or any wood for that matter, can split at any time. The actual finished chair stands 38” tall x 39” long and 33” wide. They weigh about 35 lbs. and can seat a large adult very well but also comfortable for my tiny framed wife. The rise of the seat from the knees to the ground for your feet is 13 ½ inches. The seat reclines backward naturally but not so much that it is hard to stand from a seated position. The back is curved to support the natural curve of your back allowing for a more comfortable fit. The back is 32” tall to support even a taller person. The arms have been described as looking like whales so they are narrow where they fasten to the back of the chair and wide in the front for a cup, a book or even a laptop if you choose to work outside. *DISCLOSURE: Some of the links below are affiliate links. If you chose to click through and make a purchase I will earn a commission but there is no additional cost to you. It helps compensates the business for the time spent creating these posts. THANK YOU! Child’s Chair: The smaller child chairs are added to match the adult chairs to finish the family. These also are made with rough cedar milled and sanded to size to make the chairs sturdy. As with the adult chairs the wood will be thicker, wider and stronger than nominal wood. I use all true 1” lumber for the
The space behind a door is a storage spot that’s often overlooked. Build a set of shallow shelves and mount it to the wall behind your laundry room door. The materials are inexpensive. Measure the distance between the door hinge and the wall and subtract an inch. This is the maximum depth of the shelves. We used 1x4s for the sides, top and shelves. Screw the sides to the top. Then screw three 1×2 hanging strips to the sides: one top and bottom and one centered. Nail metal shelf standards to the sides. Complete the shelves by nailing a 1×2 trim piece to the sides and top. The 1×2 dresses up the shelf unit and keeps the shelves from falling off the shelf clips.
Drilling into tile is sort of a three hand operation: hold the drill, spray the water, and make sure the water stays were it’s supposed to. The Aqua Shot from Miyanaga is a great solution to your ceramic drilling woes. The Aqua Shot drill bit has a built-in water tank that feeds water to the drill as you operate, making the whole process much smoother. Just load the chamber up with water, flip a switch and drill away. The Aqua Shot works with impact drivers and the individual tips can be replaced when they get worn out without having to replace the whole tool. The Aqua Shot is available online for $82.80. Click here for a video of the Aqua Shot in action.
Currently we offer FREE FedEx/UPS small package Ground shipping and FREE ABF/YRC freight ground shipping on most orders of $49 or more within the 48 contiguous states. Some irregular shaped or oversized items may include a special handling charge. The charge will show on the product detail page of applicable products. Offer subject to change without notice.
Now, the project starts to get really interesting. While I knew that I would use pocket-hole joinery (my latest obsession) to assemble the tabletop, I couldn’t decide how to finish the wood. There were three different cans of Minwax Gel Stain on my shelf, in three different colors—Hickory, Cherrywood, and Honey Maple. In my head, I could make a credible argument in favor of each one. And though it would have helped to know where the table would eventually go, that was another question I couldn’t answer. Then it hit me: Rather than choose one stain, why not use them all? After all, I was constructing the tabletop from scraps, so it was going to have a homemade, mosaic look no matter what. In the end, using multiple stains would emphasize the rustic effect the table was going to achieve. Perfect! From there, having fought my way to a project plan, the rest came easy. Read on to see how I built the tabletop, then stained and sealed it with Minwax.
This super-strong and simple-to-build workbench is may be the project you've been looking for a long time. You have to select some free workbench plans to create yourself a working table in your shed that after you can use it when you are working on your projects and maybe it can provide you some extra storage, depends upon which plan you are choosing to DIY.
×